[U-Boot] [PATCH 3/3] board: amlogic: add support for Odroid-N2

Anand Moon linux.amoon at gmail.com
Mon Jul 22 17:08:17 UTC 2019


Hi Neil,

On Mon, 22 Jul 2019 at 16:00, Neil Armstrong <narmstrong at baylibre.com> wrote:
>
> ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd
> with the following specifications:
>
>  - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
>  - 4GB DDR4 SDRAM
>  - Gigabit Ethernet
>  - HDMI 2.1 4K/60Hz display
>  - 40-pin GPIO header
>  - 4 x USB 3.0 Host, 1 x USB OTG
>  - eMMC, microSD
>  - Infrared receiver
>
> The board directory is W400, the name of the Amlogic Reference Design
> of Amlogic G12B with Gigabit boards, which will be used for similar
> boards.
>
> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
> ---
>  board/amlogic/w400/MAINTAINERS      |   6 ++
>  board/amlogic/w400/Makefile         |   6 ++
>  board/amlogic/w400/README.odroid-n2 | 130 ++++++++++++++++++++++++++++
>  board/amlogic/w400/README.w400      | 130 ++++++++++++++++++++++++++++
>  board/amlogic/w400/w400.c           |  18 ++++
>  configs/odroid-n2_defconfig         |  56 ++++++++++++
>  6 files changed, 346 insertions(+)
>  create mode 100644 board/amlogic/w400/MAINTAINERS
>  create mode 100644 board/amlogic/w400/Makefile
>  create mode 100644 board/amlogic/w400/README.odroid-n2
>  create mode 100644 board/amlogic/w400/README.w400
>  create mode 100644 board/amlogic/w400/w400.c
>  create mode 100644 configs/odroid-n2_defconfig
>
> diff --git a/board/amlogic/w400/MAINTAINERS b/board/amlogic/w400/MAINTAINERS
> new file mode 100644
> index 0000000000..6e68fa73f7
> --- /dev/null
> +++ b/board/amlogic/w400/MAINTAINERS
> @@ -0,0 +1,6 @@
> +W400
> +M:     Neil Armstrong <narmstrong at baylibre.com>
> +S:     Maintained
> +L:     u-boot-amlogic at groups.io
> +F:     board/amlogic/w400/
> +F:     configs/odroid-n2_defconfig
> diff --git a/board/amlogic/w400/Makefile b/board/amlogic/w400/Makefile
> new file mode 100644
> index 0000000000..fac4a73afa
> --- /dev/null
> +++ b/board/amlogic/w400/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# (C) Copyright 2019 BayLibre, SAS
> +# Author: Neil Armstrong <narmstrong at baylibre.com>
> +
> +obj-y  := w400.o
> diff --git a/board/amlogic/w400/README.odroid-n2 b/board/amlogic/w400/README.odroid-n2
> new file mode 100644
> index 0000000000..90070a988d
> --- /dev/null
> +++ b/board/amlogic/w400/README.odroid-n2
> @@ -0,0 +1,130 @@
> +U-Boot for ODROID-N2
> +====================
> +
> +ODROID-N2 is a single board computer manufactured by Hardkernel
> +Co. Ltd with the following specifications:
> +
> + - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
> + - 4GB DDR4 SDRAM
> + - Gigabit Ethernet
> + - HDMI 2.1 4K/60Hz display
> + - 40-pin GPIO header
> + - 4 x USB 3.0 Host, 1 x USB OTG
> + - eMMC, microSD
> + - Infrared receiver
> +
> +Schematics are available on the manufacturer website.
> +
> +Currently the u-boot port supports the following devices:
> + - serial
> + - eMMC, microSD
> + - Ethernet
> + - I2C
> + - Regulators
> + - Reset controller
> + - Clock controller
> + - ADC
> +
> +u-boot compilation
> +==================
> +
> + > export ARCH=arm
> + > export CROSS_COMPILE=aarch64-none-elf-
> + > make odroid-n2_defconfig
> + > make
> +
> +Image creation
> +==============
> +
> +Amlogic doesn't provide sources for the firmware and for tools needed
> +to create the bootloader image, so it is necessary to obtain them from
> +the git tree published by the board vendor:
> +
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
> +

Should we checkout odroidn2-v2015.01 from Hardkernel repository.


> + > DIR=odroid-c2
> + > git clone --depth 1 \
> +       https://github.com/hardkernel/u-boot.git -b odroidc2-v2015.01 \
> +       $DIR
> +
> + > cd odroid-c2
> + > make odroidn2_defconfig
> + > make
> + > export UBOOTDIR=$PWD
> +
> + Go back to mainline U-Boot source tree then :
> + > mkdir fip
> +
> + > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
> + > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
> + > cp $UBOOTDIR/build/board/hardkernel/odroidn2/firmware/acs.bin fip/
> + > cp $UBOOTDIR/fip/g12b/bl2.bin fip/
> + > cp $UBOOTDIR/fip/g12b/bl30.bin fip/
> + > cp $UBOOTDIR/fip/g12b/bl31.img fip/
> + > cp $UBOOTDIR/fip/g12b/ddr3_1d.fw fip/
> + > cp $UBOOTDIR/fip/g12b/ddr4_1d.fw fip/
> + > cp $UBOOTDIR/fip/g12b/ddr4_2d.fw fip/
> + > cp $UBOOTDIR/fip/g12b/diag_lpddr4.fw fip/
> + > cp $UBOOTDIR/fip/g12b/lpddr4_1d.fw fip/
> + > cp $UBOOTDIR/fip/g12b/lpddr4_2d.fw fip/
> + > cp $UBOOTDIR/fip/g12b/piei.fw fip/
> + > cp $UBOOTDIR/fip/g12b/aml_ddr.fw fip/
> + > cp u-boot.bin fip/bl33.bin
> +
> + > sh fip/blx_fix.sh \
> +       fip/bl30.bin \
> +       fip/zero_tmp \
> +       fip/bl30_zero.bin \
> +       fip/bl301.bin \
> +       fip/bl301_zero.bin \
> +       fip/bl30_new.bin \
> +       bl30
> +
> + > sh fip/blx_fix.sh \
> +       fip/bl2.bin \
> +       fip/zero_tmp \
> +       fip/bl2_zero.bin \
> +       fip/acs.bin \
> +       fip/bl21_zero.bin \
> +       fip/bl2_new.bin \
> +       bl2
> +
> + > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
> +                                       --output fip/bl30_new.bin.g12a.enc \
> +                                       --level v3
> + > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
> +                                       --output fip/bl30_new.bin.enc \
> +                                       --level v3 --type bl30
> + > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
> +                                       --output fip/bl31.img.enc \
> +                                       --level v3 --type bl31
> + > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
> +                                       --output fip/bl33.bin.enc \
> +                                       --level v3 --type bl33 --compress lz4
> + > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
> +                                       --output fip/bl2.n.bin.sig
> + > $UBOOTDIR/fip/g12b/aml_encrypt_g12b --bootmk \
> +               --output fip/u-boot.bin \
> +               --bl2 fip/bl2.n.bin.sig \
> +               --bl30 fip/bl30_new.bin.enc \
> +               --bl31 fip/bl31.img.enc \
> +               --bl33 fip/bl33.bin.enc \
> +               --ddrfw1 fip/ddr4_1d.fw \
> +               --ddrfw2 fip/ddr4_2d.fw \
> +               --ddrfw3 fip/ddr3_1d.fw \
> +               --ddrfw4 fip/piei.fw \
> +               --ddrfw5 fip/lpddr4_1d.fw \
> +               --ddrfw6 fip/lpddr4_2d.fw \
> +               --ddrfw7 fip/diag_lpddr4.fw \
> +               --ddrfw8 fip/aml_ddr.fw \
> +               --level v3
> +
> +and then write the image to SD with:
> +
> + > DEV=/dev/your_sd_device
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
> diff --git a/board/amlogic/w400/README.w400 b/board/amlogic/w400/README.w400
> new file mode 100644
> index 0000000000..25b786d817
> --- /dev/null
> +++ b/board/amlogic/w400/README.w400
> @@ -0,0 +1,130 @@
> +U-Boot for Amlogic W400
> +=======================
> +
> +U200 is a reference board manufactured by Amlogic with the following
> +specifications:
> +
> + - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
> + - 2GB DDR4 SDRAM
> + - 10/100 Ethernet (Internal PHY)
> + - 1 x USB 3.0 Host
> + - eMMC
> + - SDcard
> + - Infrared receiver
> + - SDIO WiFi Module
> + - MIPI DSI Connector
> + - Audio HAT Connector
> + - PCI-E M.2 Connector
> +
> +Schematics are available from Amlogic on demand.
> +
> +Currently the u-boot port supports the following devices:
> + - serial
> + - Ethernet
> + - Regulators
> + - Clock controller
> +
> +u-boot compilation
> +==================
> +
> + > export ARCH=arm
> + > export CROSS_COMPILE=aarch64-none-elf-
> + > make w400_defconfig
> + > make
> +
> +Image creation
> +==============
> +
> +Amlogic doesn't provide sources for the firmware and for tools needed
> +to create the bootloader image, so it is necessary to obtain them from
> +the git tree published by the board vendor:
> +
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
> + > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
> + > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
> + > git clone https://github.com/BayLibre/u-boot.git -b buildroot-openlinux-20180418 amlogic-u-boot
> + > cd amlogic-u-boot
> + > make g12b_w400_v1_defconfig
> + > make
> + > export UBOOTDIR=$PWD
> +
> +Download the latest Amlogic Buildroot package, and extract it :
> + > wget http://openlinux2.amlogic.com:8000/ARM/filesystem/Linux_BSP/buildroot_openlinux_kernel_4.9_fbdev_20180706.tar.gz
> + > tar xfz buildroot_openlinux_kernel_4.9_fbdev_20180706.tar.gz buildroot_openlinux_kernel_4.9_fbdev_20180706/bootloader
> + > export BRDIR=$PWD/buildroot_openlinux_kernel_4.9_fbdev_20180706
> + > export FIPDIR=$BRDIR/bootloader/uboot-repo/fip
> +
> +Go back to mainline U-Boot source tree then :
> + > mkdir fip
> +
> + > wget https://github.com/BayLibre/u-boot/releases/download/v2017.11-libretech-cc/blx_fix_g12a.sh -O fip/blx_fix.sh
> + > cp $UBOOTDIR/build/scp_task/bl301.bin fip/
> + > cp $UBOOTDIR/build/board/amlogic/g12b_w400_v1/firmware/acs.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl2/bin/g12b/bl2.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl30/bin/g12b/bl30.bin fip/
> + > cp $BRDIR/bootloader/uboot-repo/bl31_1.3/bin/g12b/bl31.img fip/
> + > cp $FIPDIR/g12b/ddr3_1d.fw fip/
> + > cp $FIPDIR/g12b/ddr4_1d.fw fip/
> + > cp $FIPDIR/g12b/ddr4_2d.fw fip/
> + > cp $FIPDIR/g12b/diag_lpddr4.fw fip/
> + > cp $FIPDIR/g12b/lpddr4_1d.fw fip/
> + > cp $FIPDIR/g12b/lpddr4_2d.fw fip/
> + > cp $FIPDIR/g12b/piei.fw fip/
> + > cp $FIPDIR/g12b/aml_ddr.fw fip/
> + > cp u-boot.bin fip/bl33.bin
> +
> + > sh fip/blx_fix.sh \
> +       fip/bl30.bin \
> +       fip/zero_tmp \
> +       fip/bl30_zero.bin \
> +       fip/bl301.bin \
> +       fip/bl301_zero.bin \
> +       fip/bl30_new.bin \
> +       bl30
> +
> + > sh fip/blx_fix.sh \
> +       fip/bl2.bin \
> +       fip/zero_tmp \
> +       fip/bl2_zero.bin \
> +       fip/acs.bin \
> +       fip/bl21_zero.bin \
> +       fip/bl2_new.bin \
> +       bl2
> +
> + > $FIPDIR/g12b/aml_encrypt_g12b --bl30sig --input fip/bl30_new.bin \
> +                                       --output fip/bl30_new.bin.g12a.enc \
> +                                       --level v3
> + > $FIPDIR/g12b/aml_encrypt_g12b --bl3sig --input fip/bl30_new.bin.g12a.enc \
> +                                       --output fip/bl30_new.bin.enc \
> +                                       --level v3 --type bl30
> + > $FIPDIR/g12b/aml_encrypt_g12b --bl3sig --input fip/bl31.img \
> +                                       --output fip/bl31.img.enc \
> +                                       --level v3 --type bl31
> + > $FIPDIR/g12b/aml_encrypt_g12b --bl3sig --input fip/bl33.bin --compress lz4 \
> +                                       --output fip/bl33.bin.enc \
> +                                       --level v3 --type bl33
> + > $FIPDIR/g12b/aml_encrypt_g12b --bl2sig --input fip/bl2_new.bin \
> +                                       --output fip/bl2.n.bin.sig
> + > $FIPDIR/g12b/aml_encrypt_g12b --bootmk \
> +               --output fip/u-boot.bin \
> +               --bl2 fip/bl2.n.bin.sig \
> +               --bl30 fip/bl30_new.bin.enc \
> +               --bl31 fip/bl31.img.enc \
> +               --bl33 fip/bl33.bin.enc \
> +               --ddrfw1 fip/ddr4_1d.fw \
> +               --ddrfw2 fip/ddr4_2d.fw \
> +               --ddrfw3 fip/ddr3_1d.fw \
> +               --ddrfw4 fip/piei.fw \
> +               --ddrfw5 fip/lpddr4_1d.fw \
> +               --ddrfw6 fip/lpddr4_2d.fw \
> +               --ddrfw7 fip/diag_lpddr4.fw \
> +               --ddrfw8 fip/aml_ddr.fw \
> +               --level v3
> +
> +and then write the image to SD with:
> +
> + > DEV=/dev/your_sd_device
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
> + > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
> diff --git a/board/amlogic/w400/w400.c b/board/amlogic/w400/w400.c
> new file mode 100644
> index 0000000000..4737865367
> --- /dev/null
> +++ b/board/amlogic/w400/w400.c
> @@ -0,0 +1,18 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2016 BayLibre, SAS
> + * Author: Neil Armstrong <narmstrong at baylibre.com>
> + */
> +
> +#include <common.h>
> +#include <dm.h>
> +#include <environment.h>
> +#include <asm/io.h>
> +#include <asm/arch/eth.h>
> +
> +int misc_init_r(void)
> +{
> +       meson_eth_init(PHY_INTERFACE_MODE_RGMII, 0);
> +
> +       return 0;
> +}
> diff --git a/configs/odroid-n2_defconfig b/configs/odroid-n2_defconfig
> new file mode 100644
> index 0000000000..38d1549375
> --- /dev/null
> +++ b/configs/odroid-n2_defconfig
> @@ -0,0 +1,56 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_MESON=y
> +CONFIG_SYS_TEXT_BASE=0x01000000
> +CONFIG_MESON_G12A=y
> +CONFIG_SYS_BOARD="w400"
> +CONFIG_NR_DRAM_BANKS=1
> +CONFIG_DEBUG_UART_BASE=0xff803000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_IDENT_STRING=" odroid-n2"
> +CONFIG_DEBUG_UART=y
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_MISC_INIT_R=y
> +# CONFIG_DISPLAY_CPUINFO is not set
> +# CONFIG_CMD_BDI is not set
> +# CONFIG_CMD_IMI is not set
> +CONFIG_CMD_GPIO=y
> +# CONFIG_CMD_LOADS is not set
> +CONFIG_CMD_MMC=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_OF_CONTROL=y
> +CONFIG_DEFAULT_DEVICE_TREE="meson-g12b-odroid-n2"
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_DM_GPIO=y
> +CONFIG_DM_MMC=y
> +CONFIG_MMC_MESON_GX=y
> +CONFIG_PHY_REALTEK=y
> +CONFIG_DM_ETH=y
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_PINCTRL=y
> +CONFIG_PINCTRL_MESON_G12A=y
> +CONFIG_DM_REGULATOR=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_RESET=y
> +CONFIG_DEBUG_UART_MESON=y
> +CONFIG_DEBUG_UART_ANNOUNCE=y
> +CONFIG_DEBUG_UART_SKIP_INIT=y
> +CONFIG_MESON_SERIAL=y
> +CONFIG_OF_LIBFDT_OVERLAY=y
> +CONFIG_USB=y
> +CONFIG_USB_HOST=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_PHY=y
> +CONFIG_MESON_G12A_USB_PHY=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_GADGET_DWC2_OTG=y
> +CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_MESON_G12A=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
> +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
> --
> 2.22.0
>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot


More information about the U-Boot mailing list