[U-Boot] [PATCH 03/48] pinctrl: stmfx: update pinconf settings

[Patrick Delaunay]

Alignment with kernel driver.

According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinctrl_conf_set function:

-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
 output. There is so no need to check direction.

  DIR | TYPE | PUPD | MFX GPIO configuration
  ----|------|------|---------------------------------------------------
  1   | 1    | 1    | OUTPUT open drain with internal pull-up resistor
  ----|------|------|---------------------------------------------------
  1   | 1    | 0    | OUTPUT open drain with internal pull-down resistor
  ----|------|------|---------------------------------------------------
  1   | 0    | 0/1  | OUTPUT push pull no pull
  ----|------|------|---------------------------------------------------
  0   | 1    | 1    | INPUT with internal pull-up resistor
  ----|------|------|---------------------------------------------------
  0   | 1    | 0    | INPUT with internal pull-down resistor
  ----|------|------|---------------------------------------------------
  0   | 0    | 1    | INPUT floating
  ----|------|------|---------------------------------------------------
  0   | 0    | 0    | analog (GPIO not used, default setting)

Signed-off-by: Patrick Delaunay <patrick.delaunay at st.com>
---

 drivers/pinctrl/pinctrl-stmfx.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-stmfx.c b/drivers/pinctrl/pinctrl-stmfx.c
index 5431df9..0b5a043 100644
--- a/drivers/pinctrl/pinctrl-stmfx.c
+++ b/drivers/pinctrl/pinctrl-stmfx.c
@@ -231,23 +231,23 @@ static int stmfx_pinctrl_conf_set(struct udevice *dev, unsigned int pin,
 	switch (param) {
 	case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT:
 	case PIN_CONFIG_BIAS_DISABLE:
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		ret = stmfx_pinctrl_set_type(dev, pin, 0);
+		break;
 	case PIN_CONFIG_BIAS_PULL_DOWN:
+		ret = stmfx_pinctrl_set_type(dev, pin, 1);
+		if (ret)
+			return ret;
 		ret = stmfx_pinctrl_set_pupd(dev, pin, 0);
 		break;
 	case PIN_CONFIG_BIAS_PULL_UP:
+		ret = stmfx_pinctrl_set_type(dev, pin, 1);
+		if (ret)
+			return ret;
 		ret = stmfx_pinctrl_set_pupd(dev, pin, 1);
 		break;
 	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
-		if (dir == GPIOF_OUTPUT)
-			ret = stmfx_pinctrl_set_type(dev, pin, 1);
-		else
-			ret = stmfx_pinctrl_set_type(dev, pin, 0);
-		break;
-	case PIN_CONFIG_DRIVE_PUSH_PULL:
-		if (dir == GPIOF_OUTPUT)
-			ret = stmfx_pinctrl_set_type(dev, pin, 0);
-		else
-			ret = stmfx_pinctrl_set_type(dev, pin, 1);
+		ret = stmfx_pinctrl_set_type(dev, pin, 1);
 		break;
 	case PIN_CONFIG_OUTPUT:
 		ret = stmfx_gpio_direction_output(plat->gpio, pin, arg);
-- 
2.7.4