[U-Boot] [PATCH] ARM: imx: cm_fx6: Drop ad-hoc SATA binding
Stefano Babic
sbabic at denx.de
Mon Jun 10 14:24:28 UTC 2019
Hi Marek,
On 12/05/19 22:43, Marek Vasut wrote:
> Drop the ad-hoc AHCI binding code, this is superseded by
> CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c
>
> Signed-off-by: Marek Vasut <marex at denx.de>
> Cc: Christopher Spinrath <christopher.spinrath at rwth-aachen.de>
> Cc: Fabio Estevam <fabio.estevam at nxp.com>
> Cc: Igor Grinberg <grinberg at compulab.co.il>
> Cc: Nikita Kiryanov <nikita at compulab.co.il>
> Cc: Stefano Babic <sbabic at denx.de>
> ---
> board/compulab/cm_fx6/cm_fx6.c | 63 ----------------------------------
> configs/cm_fx6_defconfig | 1 -
> 2 files changed, 64 deletions(-)
>
> diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
> index d42f57d4b7..b8f15cf3ab 100644
> --- a/board/compulab/cm_fx6/cm_fx6.c
> +++ b/board/compulab/cm_fx6/cm_fx6.c
> @@ -724,66 +724,3 @@ U_BOOT_DEVICE(cm_fx6_serial) = {
> .name = "serial_mxc",
> .platdata = &cm_fx6_mxc_serial_plat,
> };
> -
> -#if CONFIG_IS_ENABLED(AHCI)
> -static int sata_imx_probe(struct udevice *dev)
> -{
> - int i, err;
> -
> - /* Make sure this gpio has logical 0 value */
> - gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
> - udelay(100);
> - cm_fx6_sata_power(1);
cm_fx6_sata_power() is still defined and not used in the board, this
raises at least a warning (apart of Christopher's comments).
Stefano
> -
> - for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
> - err = setup_sata();
> - if (err) {
> - printf("SATA setup failed: %d\n", err);
> - return err;
> - }
> -
> - udelay(100);
> -
> - err = dwc_ahsata_probe(dev);
> - if (!err)
> - break;
> -
> - /* There is no device on the SATA port */
> - if (sata_dm_port_status(0, 0) == 0)
> - break;
> -
> - /* There's a device, but link not established. Retry */
> - device_remove(dev, DM_REMOVE_NORMAL);
> - }
> -
> - return 0;
> -}
> -
> -static int sata_imx_remove(struct udevice *dev)
> -{
> - cm_fx6_sata_power(0);
> - mdelay(250);
> -
> - return 0;
> -}
> -
> -struct ahci_ops sata_imx_ops = {
> - .port_status = dwc_ahsata_port_status,
> - .reset = dwc_ahsata_bus_reset,
> - .scan = dwc_ahsata_scan,
> -};
> -
> -static const struct udevice_id sata_imx_ids[] = {
> - { .compatible = "fsl,imx6q-ahci" },
> - { }
> -};
> -
> -U_BOOT_DRIVER(sata_imx) = {
> - .name = "dwc_ahci",
> - .id = UCLASS_AHCI,
> - .of_match = sata_imx_ids,
> - .ops = &sata_imx_ops,
> - .probe = sata_imx_probe,
> - .remove = sata_imx_remove, /* reset bus to stop it */
> -};
> -#endif /* AHCI */
> diff --git a/configs/cm_fx6_defconfig b/configs/cm_fx6_defconfig
> index ce3f9de3f9..e928cbc948 100644
> --- a/configs/cm_fx6_defconfig
> +++ b/configs/cm_fx6_defconfig
> @@ -52,7 +52,6 @@ CONFIG_DEFAULT_DEVICE_TREE="imx6q-cm-fx6"
> CONFIG_ENV_IS_IN_SPI_FLASH=y
> CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
> CONFIG_DWC_AHSATA=y
> -# CONFIG_DWC_AHSATA_AHCI is not set
> CONFIG_DM_KEYBOARD=y
> CONFIG_DM_MMC=y
> CONFIG_FSL_ESDHC=y
>
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
More information about the U-Boot
mailing list