[U-Boot] [PATCH v6 1/3] i.MX6: nand: add nandbcb command for imx
Shyam Saini
shyam.saini at amarulasolutions.com
Fri Jun 14 07:35:33 UTC 2019
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic at denx.de>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi at koi8.net>
Signed-off-by: Shyam Saini <shyam.saini at amarulasolutions.com>
---
Changes for v6:
- Consolidate v5 patch 1 and patch 2 into one single patch
- Make separate docs patch out of v5 patch 1
Changes for v5:
- Move mxs_nand.h file from drivers/mtd/nand/raw/ to include/ directory so
that it can be used by both drivers/ and arch/
- Fix command steps output in docs
Changes for v4:
- Remove obselete apis and use bch_geometry structure for calculating
ecc level, bad block start bit and bad block byte
- Write firmware only once
- Shorten variable names
- Update commit message
- Update docs as per current patch
- Fix checkpatch warnings
Changes for v3:
- Fixed multi-line comments
- Better error handling for failed allocations
Changes for v2:
- Fixed commit message notes
- Updated proper commit message
- Update doc/README.imx6 with NAND boot details
- Fixed long length variable names.
- Fixed Gigantic variable name.
- NULL checks for kzalloc
- Move Kconfig option in separate patch
- Fixed checkpatch warninigs
arch/arm/include/asm/mach-imx/imx-nandbcb.h | 111 ++++++++
arch/arm/mach-imx/Kconfig | 11 +
arch/arm/mach-imx/Makefile | 1 +
arch/arm/mach-imx/cmd_nandbcb.c | 369 +++++++++++++++++++++++++++
drivers/mtd/nand/raw/mxs_nand.c | 2 +-
drivers/mtd/nand/raw/mxs_nand_dt.c | 2 +-
drivers/mtd/nand/raw/mxs_nand_spl.c | 2 +-
{drivers/mtd/nand/raw => include}/mxs_nand.h | 0
8 files changed, 495 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/include/asm/mach-imx/imx-nandbcb.h
create mode 100644 arch/arm/mach-imx/cmd_nandbcb.c
rename {drivers/mtd/nand/raw => include}/mxs_nand.h (100%)
diff --git a/arch/arm/include/asm/mach-imx/imx-nandbcb.h b/arch/arm/include/asm/mach-imx/imx-nandbcb.h
new file mode 100644
index 0000000000..033659a038
--- /dev/null
+++ b/arch/arm/include/asm/mach-imx/imx-nandbcb.h
@@ -0,0 +1,111 @@
+/*
+ * Copyright (C) 2017 Jagan Teki <jagan at amarulasolutions.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _IMX_NAND_BCB_H_
+#define _IMX_NAND_BCB_H_
+
+#define FCB_FINGERPRINT 0x20424346 /* 'FCB' */
+#define FCB_VERSION_1 0x01000000
+
+#define DBBT_FINGERPRINT2 0x54424244 /* 'DBBT' */
+#define DBBT_VERSION_1 0x01000000
+
+struct dbbt_block {
+ u32 checksum; /* reserved on i.MX6 */
+ u32 fingerprint;
+ u32 version;
+ u32 numberbb; /* reserved on i.MX6 */
+ u32 dbbtpages;
+};
+
+struct fcb_block {
+ u32 checksum; /* First fingerprint in first byte */
+ u32 fingerprint; /* 2nd fingerprint at byte 4 */
+ u32 version; /* 3rd fingerprint at byte 8 */
+ u8 datasetup;
+ u8 datahold;
+ u8 addr_setup;
+ u8 dsample_time;
+
+ /* These are for application use only and not for ROM. */
+ u8 nandtiming;
+ u8 rea;
+ u8 rloh;
+ u8 rhoh;
+ u32 pagesize; /* 2048 for 2K pages, 4096 for 4K pages */
+ u32 oob_pagesize; /* 2112 for 2K pages, 4314 for 4K pages */
+ u32 sectors; /* Number of 2K sections per block */
+ u32 nr_nand; /* Total Number of NANDs - not used by ROM */
+ u32 nr_die; /* Number of separate chips in this NAND */
+ u32 celltype; /* MLC or SLC */
+ u32 ecc_type; /* Type of ECC, can be one of BCH-0-20 */
+ u32 ecc_nr; /* Number of bytes for Block0 - BCH */
+
+ /* Block size in bytes for all blocks other than Block0 - BCH */
+ u32 ecc_size;
+ u32 ecc_level; /* Ecc level for Block 0 - BCH */
+ u32 meta_size; /* Metadata size - BCH */
+ /* Number of blocks per page for ROM use - BCH */
+ u32 nr_blocks;
+ u32 ecc_type_sdk; /* Type of ECC, can be one of BCH-0-20 */
+ u32 ecc_nr_sdk; /* Number of bytes for Block0 - BCH */
+ /* Block size in bytes for all blocks other than Block0 - BCH */
+ u32 ecc_size_sdk;
+ u32 ecc_level_sdk; /* Ecc level for Block 0 - BCH */
+ /* Number of blocks per page for SDK use - BCH */
+ u32 nr_blocks_sdk;
+ u32 meta_size_sdk; /* Metadata size - BCH */
+ u32 erase_th; /* To set into BCH_MODE register */
+
+ /*
+ * 0: normal boot
+ * 1: to load patch starting next to FCB
+ */
+ u32 bootpatch;
+ u32 patch_size; /* Size of patch in sectors */
+ u32 fw1_start; /* Firmware image starts on this sector */
+ u32 fw2_start; /* Secondary FW Image starting Sector */
+ u32 fw1_pages; /* Number of sectors in firmware image */
+ u32 fw2_pages; /* Number of sector in secondary FW image */
+ u32 dbbt_start; /* Page address where dbbt search area begins */
+
+ /*
+ * Byte in page data that have manufacturer marked bad block marker,
+ * this will be swapped with metadata[0] to complete page data.
+ */
+ u32 bb_byte;
+
+ /*
+ * For BCH ECC sizes other than 8 and 16 the bad block marker does not
+ * start at 0th bit of bb_byte. This field is used to get to
+ * the start bit of bad block marker byte with in bb_byte
+ */
+ u32 bb_start_bit;
+
+ /*
+ * FCB value that gives byte offset for
+ * bad block marker on physical NAND page
+ */
+ u32 phy_offset;
+ u32 bchtype;
+
+ u32 readlatency;
+ u32 predelay;
+ u32 cedelay;
+ u32 postdelay;
+ u32 cmdaddpause;
+ u32 datapause;
+ u32 tmspeed;
+ u32 busytimeout;
+
+ /* the flag to enable (1)/disable(0) bi swap */
+ u32 disbbm;
+
+ /* The swap position of main area in spare area */
+ u32 spare_offset;
+};
+
+#endif /* _IMX_NAND_BCB_H_ */
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index ec09ef240f..5dd286f9a7 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -71,6 +71,17 @@ config CMD_HDMIDETECT
This enables the 'hdmidet' command which detects if an HDMI monitor
is connected.
+config CMD_NANDBCB
+ bool "i.MX6 NAND Boot Control Block(BCB) command"
+ depends on NAND && CMD_MTDPARTS
+ default y if ARCH_MX6 && NAND_MXS
+ help
+ Unlike normal 'nand write/erase' commands, this command update
+ Boot Control Block(BCB) for i.MX6 platform NAND IP's.
+
+ This is similar to kobs-ng, which is used in Linux as separate
+ rootfs package.
+
config NXP_BOARD_REVISION
bool "Read NXP board revision from fuses"
depends on ARCH_MX6 || ARCH_MX7
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index c46984994a..96f0b89fd1 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -59,6 +59,7 @@ ifneq ($(CONFIG_SPL_BUILD),y)
obj-$(CONFIG_CMD_BMODE) += cmd_bmode.o
obj-$(CONFIG_CMD_HDMIDETECT) += cmd_hdmidet.o
obj-$(CONFIG_CMD_DEKBLOB) += cmd_dek.o
+obj-$(CONFIG_CMD_NANDBCB) += cmd_nandbcb.o
endif
PLUGIN = board/$(BOARDDIR)/plugin
diff --git a/arch/arm/mach-imx/cmd_nandbcb.c b/arch/arm/mach-imx/cmd_nandbcb.c
new file mode 100644
index 0000000000..065b814b2e
--- /dev/null
+++ b/arch/arm/mach-imx/cmd_nandbcb.c
@@ -0,0 +1,369 @@
+/*
+ * i.MX6 nand boot control block(bcb).
+ *
+ * Based on the common/imx-bbu-nand-fcb.c from barebox and imx kobs-ng
+ *
+ * Copyright (C) 2017 Jagan Teki <jagan at amarulasolutions.com>
+ * Copyright (C) 2016 Sergey Kubushyn <ksi at koi8.net>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <nand.h>
+
+#include <asm/io.h>
+#include <jffs2/jffs2.h>
+#include <linux/mtd/mtd.h>
+
+#include <asm/mach-imx/imx-nandbcb.h>
+#include <asm/mach-imx/imximage.cfg>
+#include <mxs_nand.h>
+#include <linux/mtd/mtd.h>
+#include <nand.h>
+
+#define BF_VAL(v, bf) (((v) & bf##_MASK) >> bf##_OFFSET)
+#define GETBIT(v, n) (((v) >> (n)) & 0x1)
+
+static u8 calculate_parity_13_8(u8 d)
+{
+ u8 p = 0;
+
+ p |= (GETBIT(d, 6) ^ GETBIT(d, 5) ^ GETBIT(d, 3) ^ GETBIT(d, 2)) << 0;
+ p |= (GETBIT(d, 7) ^ GETBIT(d, 5) ^ GETBIT(d, 4) ^ GETBIT(d, 2) ^
+ GETBIT(d, 1)) << 1;
+ p |= (GETBIT(d, 7) ^ GETBIT(d, 6) ^ GETBIT(d, 5) ^ GETBIT(d, 1) ^
+ GETBIT(d, 0)) << 2;
+ p |= (GETBIT(d, 7) ^ GETBIT(d, 4) ^ GETBIT(d, 3) ^ GETBIT(d, 0)) << 3;
+ p |= (GETBIT(d, 6) ^ GETBIT(d, 4) ^ GETBIT(d, 3) ^ GETBIT(d, 2) ^
+ GETBIT(d, 1) ^ GETBIT(d, 0)) << 4;
+
+ return p;
+}
+
+static void encode_hamming_13_8(void *_src, void *_ecc, size_t size)
+{
+ int i;
+ u8 *src = _src;
+ u8 *ecc = _ecc;
+
+ for (i = 0; i < size; i++)
+ ecc[i] = calculate_parity_13_8(src[i]);
+}
+
+static u32 calc_chksum(void *buf, size_t size)
+{
+ u32 chksum = 0;
+ u8 *bp = buf;
+ size_t i;
+
+ for (i = 0; i < size; i++)
+ chksum += bp[i];
+
+ return ~chksum;
+}
+
+static void fill_fcb(struct fcb_block *fcb, struct mtd_info *mtd)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct mxs_nand_info *nand_info = nand_get_controller_data(chip);
+
+ fcb->fingerprint = FCB_FINGERPRINT;
+ fcb->version = FCB_VERSION_1;
+ fcb->pagesize = mtd->writesize;
+ fcb->oob_pagesize = mtd->writesize + mtd->oobsize;
+ fcb->sectors = mtd->erasesize / mtd->writesize;
+
+ /* Divide ECC strength by two and save the value into FCB structure. */
+ fcb->ecc_level = nand_info->bch_geometry.ecc_strength >> 1;
+
+ fcb->ecc_type = fcb->ecc_level;
+
+ /* Also hardcoded in kobs-ng */
+ fcb->ecc_nr = 0x00000200;
+ fcb->ecc_size = 0x00000200;
+ fcb->datasetup = 80;
+ fcb->datahold = 60;
+ fcb->addr_setup = 25;
+ fcb->dsample_time = 6;
+ fcb->meta_size = 10;
+
+ /* DBBT search area starts at second page on first block */
+ fcb->dbbt_start = 1;
+
+ fcb->bb_byte = nand_info->bch_geometry.block_mark_byte_offset;
+ fcb->bb_start_bit = nand_info->bch_geometry.block_mark_bit_offset;
+
+ fcb->phy_offset = mtd->writesize;
+
+ fcb->nr_blocks = mtd->writesize / fcb->ecc_nr - 1;
+
+ fcb->checksum = calc_chksum((void *)fcb + 4, sizeof(*fcb) - 4);
+}
+
+static int dbbt_fill_data(struct mtd_info *mtd, void *buf, int num_blocks)
+{
+ int n, n_bad_blocks = 0;
+ u32 *bb = buf + 0x8;
+ u32 *n_bad_blocksp = buf + 0x4;
+
+ for (n = 0; n < num_blocks; n++) {
+ loff_t offset = n * mtd->erasesize;
+ if (mtd_block_isbad(mtd, offset)) {
+ n_bad_blocks++;
+ *bb = n;
+ bb++;
+ }
+ }
+
+ *n_bad_blocksp = n_bad_blocks;
+
+ return n_bad_blocks;
+}
+
+static int nandbcb_update(struct mtd_info *mtd, loff_t off, size_t size,
+ size_t maxsize, const u_char *buf)
+{
+ nand_erase_options_t opts;
+ struct fcb_block *fcb;
+ struct dbbt_block *dbbt;
+ loff_t fw1_off;
+ void *fwbuf, *fcb_raw_page, *dbbt_page, *dbbt_data_page;
+ int nr_blks, nr_blks_fcb, fw1_blk;
+ size_t fwsize, dummy;
+ int i, ret;
+
+ /* erase */
+ memset(&opts, 0, sizeof(opts));
+ opts.offset = off;
+ opts.length = maxsize - 1;
+ ret = nand_erase_opts(mtd, &opts);
+ if (ret) {
+ printf("%s: erase failed (ret = %d)\n", __func__, ret);
+ return ret;
+ }
+
+ /*
+ * Reference documentation from i.MX6DQRM section 8.5.2.2
+ *
+ * Nand Boot Control Block(BCB) contains two data structures,
+ * - Firmware Configuration Block(FCB)
+ * - Discovered Bad Block Table(DBBT)
+ *
+ * FCB contains,
+ * - nand timings
+ * - DBBT search page address,
+ * - start page address of primary firmware
+ * - start page address of secondary firmware
+ *
+ * setup fcb:
+ * - number of blocks = mtd partition size / mtd erasesize
+ * - two firmware blocks, primary and secondary
+ * - first 4 block for FCB/DBBT
+ * - rest split in half for primary and secondary firmware
+ * - same firmware will write two times
+ */
+ nr_blks_fcb = 2;
+ nr_blks = maxsize / mtd->erasesize;
+ fw1_blk = nr_blks_fcb;
+
+ /* write fw */
+ fwsize = ALIGN(size + FLASH_OFFSET_STANDARD + mtd->writesize,
+ mtd->writesize);
+ fwbuf = kzalloc(fwsize, GFP_KERNEL);
+ if (!fwbuf) {
+ debug("failed to allocate fwbuf\n");
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ memcpy(fwbuf + FLASH_OFFSET_STANDARD, buf, size);
+ fw1_off = fw1_blk * mtd->erasesize;
+ ret = nand_write_skip_bad(mtd, fw1_off, &fwsize, NULL, maxsize,
+ (u_char *)fwbuf, WITH_WR_VERIFY);
+ printf("NAND fw write: 0x%llx offset, 0x%x bytes written: %s\n",
+ fw1_off, fwsize, ret ? "ERROR" : "OK");
+ if (ret)
+ goto fwbuf_err;
+
+ /* fill fcb */
+ fcb = kzalloc(sizeof(*fcb), GFP_KERNEL);
+ if (!fcb) {
+ debug("failed to allocate fcb\n");
+ ret = -ENOMEM;
+ goto fwbuf_err;
+ }
+
+ fcb->fw1_start = (fw1_blk * mtd->erasesize) / mtd->writesize;
+ fcb->fw1_pages = size / mtd->writesize + 1;
+ fill_fcb(fcb, mtd);
+
+ /* fill dbbt */
+ dbbt_page = kzalloc(mtd->writesize, GFP_KERNEL);
+ if (!dbbt_page) {
+ debug("failed to allocate dbbt_page\n");
+ ret = -ENOMEM;
+ goto fcb_err;
+ }
+
+ dbbt_data_page = kzalloc(mtd->writesize, GFP_KERNEL);
+ if (!dbbt_data_page) {
+ debug("failed to allocate dbbt_data_page\n");
+ ret = -ENOMEM;
+ goto dbbt_page_err;
+ }
+
+ dbbt = dbbt_page;
+ dbbt->checksum = 0;
+ dbbt->fingerprint = DBBT_FINGERPRINT2;
+ dbbt->version = DBBT_VERSION_1;
+ ret = dbbt_fill_data(mtd, dbbt_data_page, nr_blks);
+ if (ret < 0)
+ goto dbbt_data_page_err;
+ else if (ret > 0)
+ dbbt->dbbtpages = 1;
+
+ /* write fcb/dbbt */
+ fcb_raw_page = kzalloc(mtd->writesize + mtd->oobsize, GFP_KERNEL);
+ if (!fcb_raw_page) {
+ debug("failed to allocate fcb_raw_page\n");
+ ret = -ENOMEM;
+ goto dbbt_data_page_err;
+ }
+
+ memcpy(fcb_raw_page + 12, fcb, sizeof(struct fcb_block));
+ encode_hamming_13_8(fcb_raw_page + 12, fcb_raw_page + 12 + 512, 512);
+ /*
+ * Set the first and second byte of OOB data to 0xFF, not 0x00. These
+ * bytes are used as the Manufacturers Bad Block Marker (MBBM). Since
+ * the FCB is mostly written to the first page in a block, a scan for
+ * factory bad blocks will detect these blocks as bad, e.g. when
+ * function nand_scan_bbt() is executed to build a new bad block table.
+ */
+ memset(fcb_raw_page + mtd->writesize, 0xFF, 2);
+
+ for (i = 0; i < nr_blks_fcb; i++) {
+ if (mtd_block_isbad(mtd, off)) {
+ printf("Block %d is bad, skipped\n", i);
+ continue;
+ }
+
+ /* raw write */
+ mtd_oob_ops_t ops = {
+ .datbuf = (u8 *)fcb_raw_page,
+ .oobbuf = ((u8 *)fcb_raw_page) + mtd->writesize,
+ .len = mtd->writesize,
+ .ooblen = mtd->oobsize,
+ .mode = MTD_OPS_RAW
+ };
+
+ ret = mtd_write_oob(mtd, mtd->erasesize * i, &ops);
+ if (ret)
+ goto fcb_raw_page_err;
+ debug("NAND fcb write: 0x%x offset, 0x%x bytes written: %s\n",
+ mtd->erasesize * i, ops.len, ret ? "ERROR" : "OK");
+
+ ret = mtd_write(mtd, mtd->erasesize * i + mtd->writesize,
+ mtd->writesize, &dummy, dbbt_page);
+ if (ret)
+ goto fcb_raw_page_err;
+ debug("NAND dbbt write: 0x%x offset, 0x%x bytes written: %s\n",
+ mtd->erasesize * i + mtd->writesize, dummy,
+ ret ? "ERROR" : "OK");
+
+ /* dbbtpages == 0 if no bad blocks */
+ if (dbbt->dbbtpages > 0) {
+ loff_t to = (mtd->erasesize * i + mtd->writesize * 5);
+
+ ret = mtd_write(mtd, to, mtd->writesize, &dummy,
+ dbbt_data_page);
+ if (ret)
+ goto fcb_raw_page_err;
+ }
+ }
+
+fcb_raw_page_err:
+ kfree(fcb_raw_page);
+dbbt_data_page_err:
+ kfree(dbbt_data_page);
+dbbt_page_err:
+ kfree(dbbt_page);
+fcb_err:
+ kfree(fcb);
+fwbuf_err:
+ kfree(fwbuf);
+err:
+ return ret;
+}
+
+static int do_nandbcb_update(int argc, char * const argv[])
+{
+ struct mtd_info *mtd;
+ loff_t addr, offset, size, maxsize;
+ char *endp;
+ u_char *buf;
+ int dev;
+ int ret;
+
+ if (argc != 4)
+ return CMD_RET_USAGE;
+
+ dev = nand_curr_device;
+ if (dev < 0) {
+ printf("failed to get nand_curr_device, run nand device");
+ return CMD_RET_FAILURE;
+ }
+
+ addr = simple_strtoul(argv[1], &endp, 16);
+ if (*argv[1] == 0 || *endp != 0)
+ return CMD_RET_FAILURE;
+
+ mtd = get_nand_dev_by_index(dev);
+ if (mtd_arg_off_size(argc - 2, argv + 2, &dev, &offset, &size,
+ &maxsize, MTD_DEV_TYPE_NAND, mtd->size))
+ return CMD_RET_FAILURE;
+
+ buf = map_physmem(addr, size, MAP_WRBACK);
+ if (!buf) {
+ puts("failed to map physical memory\n");
+ return CMD_RET_FAILURE;
+ }
+
+ ret = nandbcb_update(mtd, offset, size, maxsize, buf);
+
+ return ret == 0 ? CMD_RET_SUCCESS : CMD_RET_FAILURE;
+}
+
+static int do_nandbcb(cmd_tbl_t *cmdtp, int flag, int argc,
+ char * const argv[])
+{
+ const char *cmd;
+ int ret = 0;
+
+ if (argc < 5)
+ goto usage;
+
+ cmd = argv[1];
+ --argc;
+ ++argv;
+
+ if (strcmp(cmd, "update") == 0) {
+ ret = do_nandbcb_update(argc, argv);
+ goto done;
+ }
+
+done:
+ if (ret != -1)
+ return ret;
+usage:
+ return CMD_RET_USAGE;
+}
+
+static char nandbcb_help_text[] =
+ "update addr off|partition len - update 'len' bytes starting at\n"
+ " 'off|part' to memory address 'addr', skipping bad blocks";
+
+U_BOOT_CMD(nandbcb, 5, 1, do_nandbcb,
+ "i.MX6 Nand BCB",
+ nandbcb_help_text
+);
diff --git a/drivers/mtd/nand/raw/mxs_nand.c b/drivers/mtd/nand/raw/mxs_nand.c
index b93d77a395..a41b9620d0 100644
--- a/drivers/mtd/nand/raw/mxs_nand.c
+++ b/drivers/mtd/nand/raw/mxs_nand.c
@@ -25,7 +25,7 @@
#include <asm/mach-imx/regs-bch.h>
#include <asm/mach-imx/regs-gpmi.h>
#include <asm/arch/sys_proto.h>
-#include "mxs_nand.h"
+#include <mxs_nand.h>
#define MXS_NAND_DMA_DESCRIPTOR_COUNT 4
diff --git a/drivers/mtd/nand/raw/mxs_nand_dt.c b/drivers/mtd/nand/raw/mxs_nand_dt.c
index 44dec5dedf..8ad7d618c6 100644
--- a/drivers/mtd/nand/raw/mxs_nand_dt.c
+++ b/drivers/mtd/nand/raw/mxs_nand_dt.c
@@ -15,7 +15,7 @@
#include <linux/ioport.h>
#include <linux/printk.h>
-#include "mxs_nand.h"
+#include <mxs_nand.h>
struct mxs_nand_dt_data {
unsigned int max_ecc_strength_supported;
diff --git a/drivers/mtd/nand/raw/mxs_nand_spl.c b/drivers/mtd/nand/raw/mxs_nand_spl.c
index ee7d9cb957..975a91a37d 100644
--- a/drivers/mtd/nand/raw/mxs_nand_spl.c
+++ b/drivers/mtd/nand/raw/mxs_nand_spl.c
@@ -6,7 +6,7 @@
#include <common.h>
#include <nand.h>
#include <malloc.h>
-#include "mxs_nand.h"
+#include <mxs_nand.h>
static struct mtd_info *mtd;
static struct nand_chip nand_chip;
diff --git a/drivers/mtd/nand/raw/mxs_nand.h b/include/mxs_nand.h
similarity index 100%
rename from drivers/mtd/nand/raw/mxs_nand.h
rename to include/mxs_nand.h
--
2.11.0
More information about the U-Boot
mailing list