[U-Boot] [PATCH 3/4] usb: xhci-dwc3: Add USB2 PHY configuration
Mark Kettenis
mark.kettenis at xs4all.nl
Sun Jun 30 14:25:29 UTC 2019
> From: Marek Vasut <marex at denx.de>
> Date: Sun, 30 Jun 2019 15:36:03 +0200
>
> On 6/30/19 3:31 PM, Kever Yang wrote:
> > Hi Mark,
> >
> > I add Marek and Bin Meng for this patch, I'm not sure where
> >
> > are these phy setting should go.
> >
> > Thanks,
> > - Kever
> > On 06/30/2019 12:29 AM, Mark Kettenis wrote:
> >> Configure USB2 PHY register based on "phy_type" property and
> >> handle all the quirks that are relevant for Rockchip RK3399 SoCs.
>
> Is this a documented DT property or some ad-hoc U-Boot one ?
Yes, these are all standard Linux DT properties. See usb/generic.txt
for "phy_type", and usb/dwc3.txt for "snps,dis-enblslpm_quirk" and
"snps,dis-u2-freeclk-exists-quirk".
> Is this a fix for this release or feature for next ?
Good question. The series fixes a regression, but that regression was
already present in 2019.04 and you can still boot from uSD, eMMC or
USB2 without this fixed.
> >> Signed-off-by: Mark Kettenis <kettenis at openbsd.org>
> >> ---
> >> drivers/usb/host/xhci-dwc3.c | 20 ++++++++++++++++++++
> >> 1 file changed, 20 insertions(+)
> >>
> >> diff --git a/drivers/usb/host/xhci-dwc3.c b/drivers/usb/host/xhci-dwc3.c
> >> index 83b9f119e7..ed955dc8b8 100644
> >> --- a/drivers/usb/host/xhci-dwc3.c
> >> +++ b/drivers/usb/host/xhci-dwc3.c
> >> @@ -118,6 +118,8 @@ static int xhci_dwc3_probe(struct udevice *dev)
> >> struct dwc3 *dwc3_reg;
> >> enum usb_dr_mode dr_mode;
> >> struct xhci_dwc3_platdata *plat = dev_get_platdata(dev);
> >> + const char *phy;
> >> + u32 reg;
> >> int ret;
> >>
> >> hccr = (struct xhci_hccr *)((uintptr_t)dev_read_addr(dev));
> >> @@ -132,6 +134,24 @@ static int xhci_dwc3_probe(struct udevice *dev)
> >>
> >> dwc3_core_init(dwc3_reg);
> >>
> >> + /* Set dwc3 usb2 phy config */
> >> + reg = readl(&dwc3_reg->g_usb2phycfg[0]);
> >> +
> >> + phy = dev_read_string(dev, "phy_type");
> >> + if (phy && strcmp(phy, "utmi_wide") == 0) {
> >> + reg |= DWC3_GUSB2PHYCFG_PHYIF;
> >> + reg &= ~DWC3_GUSB2PHYCFG_USBTRDTIM_MASK;
> >> + reg |= DWC3_GUSB2PHYCFG_USBTRDTIM_16BIT;
> >> + }
> >> +
> >> + if (dev_read_bool(dev, "snps,dis-enblslpm-quirk"))
> >> + reg &= ~DWC3_GUSB2PHYCFG_ENBLSLPM;
> >> +
> >> + if (dev_read_bool(dev, "snps,dis-u2-freeclk-exists-quirk"))
> >> + reg &= ~DWC3_GUSB2PHYCFG_U2_FREECLK_EXISTS;
> >> +
> >> + writel(reg, &dwc3_reg->g_usb2phycfg[0]);
> >> +
> >> dr_mode = usb_get_dr_mode(dev_of_offset(dev));
> >> if (dr_mode == USB_DR_MODE_UNKNOWN)
> >> /* by default set dual role mode to HOST */
> >
> >
> >
>
>
> --
> Best regards,
> Marek Vasut
>
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-56 Email: marex at denx.de
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
More information about the U-Boot
mailing list