[U-Boot] [PATCH v4 0/9] arm: exynos: Fix reboot on Odroid HC1

Minkyu Kang mk7.kang at samsung.com
Wed Mar 6 07:03:28 UTC 2019


Dear Krzysztof Kozlowski,

On 06/03/2019 04:57, Krzysztof Kozlowski wrote:
> Hi,
> 
> Changes since v3
> ================
> 1. Add accumulated review and test tags.
> 2. Patch 6: Add "ramp" keyword to new function (as discussed with
>    Torsten Duwe).
> 3. Rebased on v2019.04-rc3.
> 
> 
> Changes since v2
> ================
> 1. Add Lukasz review tags.
> 2. Patch 7: Return on error, as suggested by Simon.
> 2. Patch 3: Use IS_ENABLED() to run revision detection only
>    once - either during late display board or misc_init_r.
> 
> Changes since v1
> ================
> 1. Move fixes to beginning of patchset.
> 2. Patch 3: Rework the idea - split revision detection to be executed later.
> 3. Patch 4: New patch.
> 4. Patch 6: Apply Simon's comments.
> 5. Patch 6: Do not delay when changing voltage if regulator is disabled.
> 6. Patch 6: Do not delay when disabling the regulator.
> 
> 
> Description
> ===========
> Odroid HC1 does not reboot properly (at least from SD card but
> I do not expect difference on eMMC), if LDO4/VDD_ADC was turned
> off by Linux kernel.  This condition happens so far always, because
> Linux kernel did not enable ADC on Odroid HC1, therefore the
> VDD_ADC regulator was turned off as unused.
> 
> The issue is in detection of revision which later is used to load
> proper DTB.
> 
> The revision is obtained by ADC read of a voltage depending on VDD_ADC.
> Therefore:
> 1. VDD_ADC has to be turned on (but board detection happens before
>    power is initialized),
> 2. Turning VDD_ADC should wait with ramp delay,
> 3. Reading the value from ADC should wait for it to stabilize.
> 
> Tested on Odroid XU3-Lite and Odroid HC1.
> 
> Comments and testing are welcomed.
> 
> Best regards,
> Krzysztof
> 
> Krzysztof Kozlowski (9):
>   adc: exynos-adc: Fix wrong bit operation used to stop the ADC
>   power: regulator: s2mps11: Fix step for LDO27 and LDO35
>   arm: exynos: Detect revision later, when all resources are ready
>   arm: exynos: odroid-xu3: Display info late to have proper type
>   arm: exynos: Wait till ADC stabilizes before checking Odroid HC1
>     revision
>   regulator: Add support for ramp delay
>   power: regulator: s2mps11: Add enable delay
>   arm: dts: exynos: Add supply for ADC block to Odroid XU3 family
>   arm: dts: exynos: Add ramp delay property to LDO regulators to Odroid
>     XU3 family
> 
>  arch/arm/dts/exynos5422-odroidxu3.dts         | 20 +++++++
>  board/samsung/common/board.c                  | 24 ++++++++-
>  board/samsung/common/exynos5-dt-types.c       | 54 +++++++++++++++++--
>  board/samsung/odroid/odroid.c                 |  8 +++
>  configs/odroid-xu3_defconfig                  |  2 +
>  .../regulator/regulator.txt                   |  2 +
>  drivers/adc/exynos-adc.c                      |  2 +-
>  drivers/power/regulator/regulator-uclass.c    | 47 +++++++++++++++-
>  drivers/power/regulator/s2mps11_regulator.c   | 15 +++++-
>  include/power/regulator.h                     |  2 +
>  include/samsung/misc.h                        |  1 +
>  11 files changed, 167 insertions(+), 10 deletions(-)
> 

Build was failed after apply your patch on trats, trats2 and s5pc210_universal.
Please check.

board/samsung/common/built-in.o: In function `misc_init_r':
/home/share/Work/u-boot-samsung/board/samsung/common/board.c:307: undefined reference to `set_board_revision'

Thanks,
Minkyu Kang.


More information about the U-Boot mailing list