[U-Boot] [PATCH] pm9g45: Migrate to CONFIG_DM
Ilko Iliev
iliev at ronetix.at
Thu Mar 7 15:05:02 UTC 2019
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev at ronetix.at>
---
board/ronetix/pm9g45/pm9g45.c | 8 +-
configs/pm9g45_defconfig | 44 +++++++--
include/configs/pm9g45.h | 173 ++++++++++++++++++----------------
3 files changed, 132 insertions(+), 93 deletions(-)
diff --git a/board/ronetix/pm9g45/pm9g45.c b/board/ronetix/pm9g45/pm9g45.c
index 17e520a9e9..871db4abea 100644
--- a/board/ronetix/pm9g45/pm9g45.c
+++ b/board/ronetix/pm9g45/pm9g45.c
@@ -139,15 +139,15 @@ int board_init(void)
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
- gd->ram_size = get_ram_size((void *)PHYS_SDRAM,
- PHYS_SDRAM_SIZE);
+ gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+ CONFIG_SYS_SDRAM_SIZE);
return 0;
}
int dram_init_banksize(void)
{
- gd->bd->bi_dram[0].start = PHYS_SDRAM;
- gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ gd->bd->bi_dram[0].size = CONFIG_SYS_SDRAM_SIZE;
return 0;
}
diff --git a/configs/pm9g45_defconfig b/configs/pm9g45_defconfig
index 928e446c3f..c3f7e1408d 100644
--- a/configs/pm9g45_defconfig
+++ b/configs/pm9g45_defconfig
@@ -2,27 +2,57 @@ CONFIG_ARM=y
CONFIG_ARCH_AT91=y
CONFIG_SYS_TEXT_BASE=0x73f00000
CONFIG_TARGET_PM9G45=y
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_DEBUG_UART_BOARD_INIT=y
+CONFIG_DEBUG_UART_BASE=0xffffee00
+CONFIG_DEBUG_UART_CLOCK=132000000
+CONFIG_DEBUG_UART=y
CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9G45"
+CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="fbcon=rotate:3 console=tty0 console=ttyS0,115200 root=/dev/mtdblock4 mtdparts=atmel_nand:128k(bootstrap)ro,256k(uboot)ro,1664k(env),2M(linux)ro,-(root) rw rootfstype=jffs2"
-# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_CONSOLE_MUX is not set
+CONFIG_SYS_CONSOLE_IS_IN_ENV=y
# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_PROMPT="U-Boot> "
+# CONFIG_CMD_BDI is not set
+CONFIG_CMD_BOOTZ=y
+# CONFIG_CMD_IMI is not set
# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
CONFIG_CMD_NAND=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_JFFS2=y
+CONFIG_CMD_FAT=y
+CONFIG_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="at91sam9m10g45ek"
CONFIG_ENV_IS_IN_NAND=y
-# CONFIG_MMC is not set
-CONFIG_NAND=y
+CONFIG_DM=y
+CONFIG_CLK=y
+CONFIG_CLK_AT91=y
+CONFIG_DM_GPIO=y
+CONFIG_AT91_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_GENERIC_ATMEL_MCI=y
CONFIG_NAND_ATMEL=y
+CONFIG_DM_ETH=y
+CONFIG_MACB=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_AT91=y
+CONFIG_DM_SERIAL=y
+CONFIG_DEBUG_UART_ATMEL=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_ATMEL_USART=y
+CONFIG_TIMER=y
+CONFIG_ATMEL_PIT_TIMER=y
CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
diff --git a/include/configs/pm9g45.h b/include/configs/pm9g45.h
index 46b8030894..e34873cea7 100644
--- a/include/configs/pm9g45.h
+++ b/include/configs/pm9g45.h
@@ -15,110 +15,119 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * SoC must be defined first, before hardware.h is included.
- * In this case SoC is defined in boards.cfg.
- */
-#include <asm/hardware.h>
-
-#define CONFIG_SYS_AT91_CPU_NAME "AT91SAM9G45"
-
-#define CONFIG_MACH_TYPE MACH_TYPE_PM9G45
-
/* ARM asynchronous clock */
-#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
-#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
-
-#define CONFIG_ARCH_CPU_INIT
-
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
+#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
+#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
-/*
- * Hardware drivers
- */
-#define CONFIG_AT91_GPIO 1
-#define CONFIG_ATMEL_USART 1
-#define CONFIG_USART_BASE ATMEL_BASE_DBGU
-#define CONFIG_USART_ID ATMEL_ID_SYS
-
-#define CONFIG_SYS_USE_NANDFLASH 1
-
-/* LED */
-#define CONFIG_AT91_LED
-#define CONFIG_RED_LED GPIO_PIN_PD(31) /* this is the user1 led */
-#define CONFIG_GREEN_LED GPIO_PIN_PD(0) /* this is the user2 led */
-
+/* general purpose I/O */
+#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/*
* BOOTP options
*/
-#define CONFIG_BOOTP_BOOTFILESIZE 1
-
-#define CONFIG_JFFS2_CMDLINE 1
-#define CONFIG_JFFS2_NAND 1
-#define CONFIG_JFFS2_DEV "nand0" /* NAND dev jffs2 lives on */
-#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_SIZE (256 * 1024 * 1024) /* partition */
+#define CONFIG_BOOTP_BOOTFILESIZE
/* SDRAM */
-#define PHYS_SDRAM 0x70000000
-#define PHYS_SDRAM_SIZE 0x08000000 /* 128 megs */
+#define CONFIG_SYS_SDRAM_BASE 0x70000000
+#define CONFIG_SYS_SDRAM_SIZE 0x08000000
+
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
/* NAND flash */
#ifdef CONFIG_CMD_NAND
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE 0x40000000
-#define CONFIG_SYS_NAND_DBW_8 1
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
+#define CONFIG_SYS_NAND_DBW_8
/* our ALE is AD21 */
-#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
+#define CONFIG_SYS_NAND_MASK_ALE BIT(21)
/* our CLE is AD22 */
-#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
-#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14)
-#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(3)
-
+#define CONFIG_SYS_NAND_MASK_CLE BIT(22)
+#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
+#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD3
+#define CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
#endif
/* Ethernet */
-#define CONFIG_MACB 1
-#define CONFIG_RMII 1
-#define CONFIG_NET_RETRY_COUNT 20
-#define CONFIG_RESET_PHY_R 1
-
-/* USB */
-#define CONFIG_USB_ATMEL
-#define CONFIG_USB_ATMEL_CLK_SEL_UPLL
-#define CONFIG_USB_OHCI_NEW 1
-#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
-#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00700000 /* _UHP_OHCI_BASE */
-#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9g45"
-#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-
-/* board specific(not enough SRAM) */
-#define CONFIG_AT91SAM9G45_LCD_BASE PHYS_SDRAM + 0xE00000
-
-#define CONFIG_SYS_LOAD_ADDR PHYS_SDRAM + 0x2000000 /* load addr */
-
-#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
-#define CONFIG_SYS_MEMTEST_END CONFIG_AT91SAM9G45_LCD_BASE
-
-/* bootstrap + u-boot + env + linux in nandflash */
-#define CONFIG_ENV_OFFSET 0x60000
-#define CONFIG_ENV_OFFSET_REDUND 0x80000
-#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */
-#define CONFIG_BOOTCOMMAND "nand read 0x72000000 0x200000 0x200000; bootm"
+#define CONFIG_RESET_PHY_R
+#define CONFIG_AT91_WANTS_COMMON_PHY
+
+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
+
+#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END 0x23e00000
+
+#ifdef CONFIG_NAND_BOOT
+/* bootstrap + u-boot + env in nandflash */
+#define CONFIG_ENV_OFFSET 0x140000
+#define CONFIG_ENV_OFFSET_REDUND 0x100000
+#define CONFIG_ENV_SIZE 0x20000
+
+#define CONFIG_BOOTCOMMAND \
+ "nand read 0x70000000 0x200000 0x300000;" \
+ "bootm 0x70000000"
+#elif CONFIG_SD_BOOT
+/* bootstrap + u-boot + env + linux in mmc */
+#define CONFIG_ENV_SIZE 0x4000
+
+#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x71000000 dtb; " \
+ "fatload mmc 0:1 0x72000000 zImage; " \
+ "bootz 0x72000000 - 0x71000000"
+#endif
/*
* Size of malloc() pool
*/
-#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024,\
- 0x1000)
+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \
+ 128 * 1024, 0x1000)
+
+/* Defines for SPL */
+#define CONFIG_SPL_TEXT_BASE 0x300000
+#define CONFIG_SPL_MAX_SIZE 0x010000
+#define CONFIG_SPL_STACK 0x310000
+
+#define CONFIG_SYS_MONITOR_LEN 0x80000
+
+#ifdef CONFIG_SD_BOOT
+
+#define CONFIG_SPL_BSS_START_ADDR 0x70000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START 0x70080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
+
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#elif CONFIG_NAND_BOOT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x80000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000
+#define CONFIG_SYS_NAND_PAGE_COUNT 64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE 256
+#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_ECCPOS { 40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
- GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK 132096000
+#define CONFIG_SYS_AT91_PLLA 0x20c73f03
+#define CONFIG_SYS_MCKR 0x1301
+#define CONFIG_SYS_MCKR_CSS 0x1302
#endif
--
2.17.1
More information about the U-Boot
mailing list