[U-Boot] [PATCH] arm: exynos: odroid: Fix build if BOARD_TYPES are not set

[Minkyu Kang]

On 06/03/2019 18:23, Krzysztof Kozlowski wrote:
> CONFIG_BOARD_TYPES is necessary for Odroid X/X2/U3 boards to detect
> proper revision.  However building should succeed even without it.
> While moving code around, document also the reference clock selection.
> 
> This fixes the build error without CONFIG_BOARD_TYPES:
> 
>     board/samsung/odroid/odroid.c: In function 'board_usb_init':
>     board/samsung/odroid/odroid.c:473:8: error: 'gd_t' {aka 'volatile struct global_data'} has no member named 'board_type'
>       if (gd->board_type == ODROID_TYPE_U3)
>             ^~
> 
> Signed-off-by: Krzysztof Kozlowski <krzk at kernel.org>
> ---
>  board/samsung/odroid/odroid.c | 27 +++++++++++++++++++++------
>  1 file changed, 21 insertions(+), 6 deletions(-)
> 
> diff --git a/board/samsung/odroid/odroid.c b/board/samsung/odroid/odroid.c
> index 552333fe869d..b11d99223346 100644
> --- a/board/samsung/odroid/odroid.c
> +++ b/board/samsung/odroid/odroid.c
> @@ -462,18 +462,33 @@ struct dwc2_plat_otg_data s5pc210_otg_data = {
>  
>  #if defined(CONFIG_USB_GADGET) || defined(CONFIG_CMD_USB)
>  
> +static void set_usb3503_ref_clk(void)
> +{
> +#ifdef CONFIG_BOARD_TYPES
> +	/*
> +	 * gpx3-0 chooses primary (low) or secondary (high) reference clock
> +	 * frequencies table.  The choice of clock is done through hard-wired
> +	 * REF_SEL pins.
> +	 * The Odroid Us have reference clock at 24 MHz (00 entry from secondary
> +	 * table) and Odroid Xs have it at 26 MHz (01 entry from primary table).
> +	 */
> +	if (gd->board_type == ODROID_TYPE_U3)
> +		gpio_direction_output(EXYNOS4X12_GPIO_X30, 0);
> +	else
> +		gpio_direction_output(EXYNOS4X12_GPIO_X30, 1);
> +#else
> +	/* Choose Odroid Xs frequency without board types */
> +	gpio_direction_output(EXYNOS4X12_GPIO_X30, 1);
> +#endif /* CONFIG_BOARD_TYPES */
> +}
> +
>  int board_usb_init(int index, enum usb_init_type init)
>  {
>  #ifdef CONFIG_CMD_USB
>  	struct udevice *dev;
>  	int ret;
>  
> -	/* Set Ref freq 0 => 24MHz, 1 => 26MHz*/
> -	/* Odroid Us have it at 24MHz, Odroid Xs at 26MHz */
> -	if (gd->board_type == ODROID_TYPE_U3)
> -		gpio_direction_output(EXYNOS4X12_GPIO_X30, 0);
> -	else
> -		gpio_direction_output(EXYNOS4X12_GPIO_X30, 1);
> +	set_usb3503_ref_clk();
>  
>  	/* Disconnect, Reset, Connect */
>  	gpio_direction_output(EXYNOS4X12_GPIO_X34, 0);
> 

applied to u-boot-samsung.

Thanks,
Minkyu Kang.