[U-Boot] [PATCH 1/3] usb: dwc3: Add Meson G12A USB Glue

Marek Vasut marex at denx.de
Tue Mar 26 15:53:54 UTC 2019


On 3/26/19 4:15 PM, Neil Armstrong wrote:
> Adds support for Amlogic G12A USB Control Glue HW.
> 
> The Amlogic G12A SoC Family embeds 2 USB Controllers :
> - a DWC3 IP configured as Host for USB2 and USB3
> - a DWC2 IP configured as Peripheral USB2 Only
> 
> A glue connects these both controllers to 2 USB2 PHYs, and optionnally
> to an USB3+PCIE Combo PHY shared with the PCIE controller.
> 
> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
> setups the on-chip OTG mode selection for this PHY.
> 
> This driver sets the OTG capable port as Host mode by default,
> the switch to Device mode is to be done in a separate patch.
> 
> Signed-off-by: Neil Armstrong <narmstrong at baylibre.com>
> ---

[...]

> +static int dwc3_meson_g12a_get_phys(struct dwc3_meson_g12a *priv)
> +{
> +	int i, ret;
> +
> +	for (i = 0 ; i < PHY_COUNT ; ++i) {
> +		ret = generic_phy_get_by_name(priv->dev, phy_names[i],
> +					      &priv->phys[i]);
> +		if (ret == -ENOENT)
> +			continue;
> +
> +		if (ret)
> +			return ret;
> +
> +		if (i == USB3_HOST_PHY)
> +			priv->usb3_ports++;
> +		else
> +			priv->usb2_ports++;
> +	}
> +
> +	printf("%s: usb2 ports: %d\n", __func__, priv->usb2_ports);
> +	printf("%s: usb3 ports: %d\n", __func__, priv->usb3_ports);

Are these prints needed ?

> +	return 0;
> +}

[...]
> +static int dwc3_meson_g12a_probe(struct udevice *dev)
> +{
> +	struct dwc3_meson_g12a *priv = dev_get_platdata(dev);
> +	int ret, i;
> +
> +	priv->dev = dev;
> +
> +	ret = regmap_init_mem(dev_ofnode(dev), &priv->regmap);
> +	if (ret)
> +		return ret;
> +
> +	ret = dwc3_meson_g12a_clk_init(priv);
> +	if (ret)
> +		return ret;
> +
> +	ret = dwc3_meson_g12a_reset_init(priv);
> +	if (ret)
> +		return ret;
> +
> +	ret = dwc3_meson_g12a_get_phys(priv);
> +	if (ret)
> +		return ret;
> +
> +#if CONFIG_IS_ENABLED(DM_REGULATOR)
> +	ret = device_get_supply_regulator(dev, "vbus-supply",
> +					  &priv->vbus_supply);
> +	if (ret && ret != -ENOENT) {
> +		pr_err("Failed to get PHY regulator\n");
> +		return ret;
> +	}
> +
> +	if (priv->vbus_supply) {
> +		ret = regulator_set_enable(priv->vbus_supply, true);
> +		if (ret)
> +			return ret;
> +	}
> +#endif
> +
> +	priv->otg_mode = usb_get_dr_mode(dev_of_offset(dev));
> +
> +	ret = dwc3_meson_g12a_usb_init(priv);
> +	if (ret)
> +		return ret;
> +
> +	for (i = 0 ; i < PHY_COUNT ; ++i) {
> +		if (!priv->phys[i].dev)
> +			continue;
> +
> +		ret = generic_phy_init(&priv->phys[i]);
> +		if (ret)
> +			goto err_phy_init;
> +	}

Isn't there some function to init all the PHYs already ?

-- 
Best regards,
Marek Vasut


More information about the U-Boot mailing list