[U-Boot] [EXT] Re: [PATCH 2/5] dm: spi: Convert Freescale ESPI driver to driver model
Chuanhua Han
chuanhua.han at nxp.com
Mon May 6 06:59:22 UTC 2019
> -----Original Message-----
> From: Jagan Teki <jagan at amarulasolutions.com>
> Sent: 2019年4月26日 2:07
> To: Chuanhua Han <chuanhua.han at nxp.com>
> Cc: Jagan Teki <jagan at openedev.com>; Wolfgang Denk <wd at denx.de>;
> Shengzhou Liu <shengzhou.liu at nxp.com>; Ruchika Gupta
> <ruchika.gupta at nxp.com>; U-Boot-Denx <u-boot at lists.denx.de>; Jiafei Pan
> <jiafei.pan at nxp.com>; Yinbo Zhu <yinbo.zhu at nxp.com>
> Subject: Re: [EXT] Re: [U-Boot] [PATCH 2/5] dm: spi: Convert Freescale ESPI
> driver to driver model
>
> Caution: EXT Email
>
> On Thu, Apr 25, 2019 at 8:27 AM Chuanhua Han <chuanhua.han at nxp.com>
> wrote:
> >
> > Hi,jagan
> > Thank you for your replay!
> >
> > > -----Original Message-----
> > > From: Jagan Teki <jagan at amarulasolutions.com>
> > > Sent: 2019年4月24日 14:57
> > > To: Chuanhua Han <chuanhua.han at nxp.com>
> > > Cc: Jagan Teki <jagan at openedev.com>; Wolfgang Denk <wd at denx.de>;
> > > Shengzhou Liu <shengzhou.liu at nxp.com>; Ruchika Gupta
> > > <ruchika.gupta at nxp.com>; U-Boot-Denx <u-boot at lists.denx.de>; Jiafei
> > > Pan <jiafei.pan at nxp.com>; Yinbo Zhu <yinbo.zhu at nxp.com>
> > > Subject: [EXT] Re: [U-Boot] [PATCH 2/5] dm: spi: Convert Freescale
> > > ESPI driver to driver model
> > >
> > > WARNING: This email was created outside of NXP. DO NOT CLICK links
> > > or attachments unless you recognize the sender and know the content is
> safe.
> > >
> > >
> > >
> > > On Tue, Apr 23, 2019 at 4:17 PM Chuanhua Han
> <chuanhua.han at nxp.com>
> > > wrote:
> > > >
> > > > Modify the Freescale ESPI driver to support the driver model.
> > > > Also resolved the following problems:
> > > >
> > > > ===================== WARNING ====================== This board
> > > does
> > > > not use CONFIG_DM_SPI. Please update the board before v2019.04 for
> > > > no dm conversion and v2019.07 for partially dm converted drivers.
> > > > Failure to update can lead to driver/board removal See
> > > > doc/driver-model/MIGRATION.txt for more info.
> > > > ====================================================
> > > > ===================== WARNING ====================== This board
> > > does
> > > > not use CONFIG_DM_SPI_FLASH. Please update the board to use
> > > > CONFIG_SPI_FLASH before the v2019.07 release.
> > > > Failure to update by the deadline may result in board removal.
> > > > See doc/driver-model/MIGRATION.txt for more info.
> > > > ====================================================
> > > >
> > > > Signed-off-by: Chuanhua Han <chuanhua.han at nxp.com>
> > > > ---
> > > > depends on:
> > > > -
> > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2F
> > > > patc
> > > >
> > >
> hwork.ozlabs.org%2Fproject%2Fuboot%2Flist%2F%3Fseries%3D99439&d
> > > ata
> > > >
> > >
> =02%7C01%7Cchuanhua.han%40nxp.com%7Cfa6bdd7859c4411b5d8608d6c8
> > > 8223e3%7
> > > >
> > >
> C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C1%7C63691685860819371
> > > 5&sda
> > > >
> > >
> ta=437CqPexTmJAzhl7wZ3lAUQVbmy%2B2NvHlurTcGTJKT0%3D&reserve
> > > d=0
> > > >
> > > > drivers/spi/fsl_espi.c | 450
> > > > +++++++++++++++++++++++++++++------------
> > > > 1 file changed, 316 insertions(+), 134 deletions(-)
> > > >
> > > > diff --git a/drivers/spi/fsl_espi.c b/drivers/spi/fsl_espi.c index
> > > > 7444ae1a06..6ebe57c30b 100644
> > > > --- a/drivers/spi/fsl_espi.c
> > > > +++ b/drivers/spi/fsl_espi.c
> > > > @@ -4,17 +4,27 @@
> > > > *
> > > > * Copyright 2010-2011 Freescale Semiconductor, Inc.
> > > > * Author: Mingkai Hu (Mingkai.hu at freescale.com)
> > > > + * Chuanhua Han (chuanhua.han at nxp.com)
> > > > */
> > > >
> > > > #include <common.h>
> > > > -
> > > > #include <malloc.h>
> > > > #include <spi.h>
> > > > #include <asm/immap_85xx.h>
> > > > +#include <dm.h>
> > > > +#include <errno.h>
> > > > +#include <fdtdec.h>
> > > > +
> > > > +struct fsl_espi_platdata {
> > > > + uint flags;
> > > > + uint speed_hz;
> > > > + uint num_chipselect;
> > > > + fdt_addr_t regs_addr;
> > > > +};
> > > >
> > > > -struct fsl_spi_slave {
> > > > - struct spi_slave slave;
> > > > +struct fsl_espi_priv {
> > > > ccsr_espi_t *espi;
> > > > + u32 speed_hz;
> > > > unsigned int div16;
> > > > unsigned int pm;
> > > > int tx_timeout;
> > > > @@ -25,9 +35,18 @@ struct fsl_spi_slave {
> > > > unsigned int max_transfer_length;
> > > > };
> > > >
> > > > +struct fsl_spi_slave {
> > > > + struct spi_slave slave;
> > > > + struct fsl_espi_priv priv; };
> > > > +
> > > > #define to_fsl_spi_slave(s) container_of(s, struct fsl_spi_slave,
> > > > slave)
> > > > +#define to_fsl_spi_priv(p) container_of(p, struct fsl_spi_slave,
> > > > +priv)
> > > > #define US_PER_SECOND 1000000UL
> > > >
> > > > +/* default SCK frequency, unit: HZ */
> > > > +#define FSL_ESPI_DEFAULT_SCK_FREQ 10000000
> > > > +
> > > > #define ESPI_MAX_CS_NUM 4
> > > > #define ESPI_FIFO_WIDTH_BIT 32
> > > >
> > > > @@ -62,121 +81,46 @@ struct fsl_spi_slave {
> > > >
> > > > #define ESPI_MAX_DATA_TRANSFER_LEN 0xFFF0
> > > >
> > > > -struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
> > > > - unsigned int max_hz, unsigned int mode)
> > > > -{
> > > > - struct fsl_spi_slave *fsl;
> > > > - sys_info_t sysinfo;
> > > > - unsigned long spibrg = 0;
> > > > - unsigned long spi_freq = 0;
> > > > - unsigned char pm = 0;
> > > > -
> > > > - if (!spi_cs_is_valid(bus, cs))
> > > > - return NULL;
> > > > -
> > > > - fsl = spi_alloc_slave(struct fsl_spi_slave, bus, cs);
> > > > - if (!fsl)
> > > > - return NULL;
> > > > -
> > > > - fsl->espi = (void *)(CONFIG_SYS_MPC85xx_ESPI_ADDR);
> > > > - fsl->mode = mode;
> > > > - fsl->max_transfer_length = ESPI_MAX_DATA_TRANSFER_LEN;
> > > > -
> > > > - /* Set eSPI BRG clock source */
> > > > - get_sys_info(&sysinfo);
> > > > - spibrg = sysinfo.freq_systembus / 2;
> > > > - fsl->div16 = 0;
> > > > - if ((spibrg / max_hz) > 32) {
> > > > - fsl->div16 = ESPI_CSMODE_DIV16;
> > > > - pm = spibrg / (max_hz * 16 * 2);
> > > > - if (pm > 16) {
> > > > - pm = 16;
> > > > - debug("Requested speed is too low: %d
> Hz, %ld
> > > Hz "
> > > > - "is used.\n", max_hz, spibrg / (32 *
> 16));
> > > > - }
> > > > - } else
> > > > - pm = spibrg / (max_hz * 2);
> > > > - if (pm)
> > > > - pm--;
> > > > - fsl->pm = pm;
> > > > -
> > > > - if (fsl->div16)
> > > > - spi_freq = spibrg / ((pm + 1) * 2 * 16);
> > > > - else
> > > > - spi_freq = spibrg / ((pm + 1) * 2);
> > > > -
> > > > - /* set tx_timeout to 10 times of one espi FIFO entry go out */
> > > > - fsl->tx_timeout = DIV_ROUND_UP((US_PER_SECOND *
> > > ESPI_FIFO_WIDTH_BIT
> > > > - * 10), spi_freq);
> > > > -
> > > > - return &fsl->slave;
> > > > -}
> > > > -
> > > > -void spi_free_slave(struct spi_slave *slave)
> > > > +#ifndef CONFIG_DM_SPI
> > >
> > > Would you try for full dm-conversion? it would be hard to move all
> > > respective defconfigs to use but better try since we have next
> > > version deadline for full dm-conversion. thanks!
> > Currently my espi driver is modified to be compatible with dm
> > configuration and non-dm configuration.
> > If uboot don't need non-dm code in the future, I will remove this
> > compatibility and only keep the dm driver code. Thank you.
>
> Idea is to make fully dm supported and ie what we have migration deadline,
> doc/driver-model/MIGRATION.txt
Do you mean that I need to delete the original non-dm code?
Or there are some values in the dm code that do not come from dts!
Can you tell me something about it? Thank you!
More information about the U-Boot
mailing list