[U-Boot] [PATCH 04/13] arm: K3: Introduce System Firmware loader framework

Simon Goldschmidt simon.k.r.goldschmidt at gmail.com
Tue May 7 19:21:10 UTC 2019



On 07.05.19 21:17, Andreas Dannenberg wrote:
> Hi Simon,
> 
> On Tue, May 07, 2019 at 08:16:07PM +0200, Simon Goldschmidt wrote:
>>
>>
>> On 07.05.19 19:25, Andreas Dannenberg wrote:
>>> Introduce a framework that allows loading the System Firmware (SYSFW)
>>> binary as well as the associated configuration data from an image tree
>>> blob named "sysfw.itb" from an FS-based MMC boot media or from an MMC
>>> RAW mode partition or sector.
>>>
>>> To simplify the handling of and loading from the different boot media
>>> we tap into the existing U-Boot SPL framework usually used for loading
>>> U-Boot by building on an earlier commit that exposes some of that
>>> functionality.
>>>
>>> Note that this initial implementation only supports FS and RAW-based
>>> eMMC/SD card boot.
>>>
>>> Signed-off-by: Andreas Dannenberg <dannenberg at ti.com>
>>> Signed-off-by: Lokesh Vutla <lokeshvutla at ti.com>
>>
>> Without having a too deep understanding of this, all this stuff looks like
>> it would be similar to drivers/misc/fs_loader.c?
>>
>> Could it build on top of that?
> 
> Yes and no. Can you please review the associated cover letter, it
> addresses this very question which I expected to get raised.

Ah, ok. Indeed I seemed to skip those lines when reading the cover 
letter, sorry.

Regards,
Simon

> 
> Thanks,
> Andreas
> 
>>
>> Regards,
>> Simon
>>
>>> ---
>>>    arch/arm/mach-k3/Kconfig                     |  40 +++
>>>    arch/arm/mach-k3/Makefile                    |   1 +
>>>    arch/arm/mach-k3/include/mach/sysfw-loader.h |  12 +
>>>    arch/arm/mach-k3/sysfw-loader.c              | 263 +++++++++++++++++++
>>>    4 files changed, 316 insertions(+)
>>>    create mode 100644 arch/arm/mach-k3/include/mach/sysfw-loader.h
>>>    create mode 100644 arch/arm/mach-k3/sysfw-loader.c
>>>
>>> diff --git a/arch/arm/mach-k3/Kconfig b/arch/arm/mach-k3/Kconfig
>>> index e677a2e01b..f1731dda58 100644
>>> --- a/arch/arm/mach-k3/Kconfig
>>> +++ b/arch/arm/mach-k3/Kconfig
>>> @@ -58,6 +58,46 @@ config SYS_K3_BOOT_CORE_ID
>>>    	int
>>>    	default 16
>>> +config K3_LOAD_SYSFW
>>> +	bool
>>> +	depends on SPL
>>> +	default n
>>> +
>>> +config K3_SYSFW_IMAGE_NAME
>>> +	string "File name of SYSFW firmware and configuration blob"
>>> +	depends on K3_LOAD_SYSFW
>>> +	default	"sysfw.itb"
>>> +	help
>>> +	  Filename of the combined System Firmware and configuration image tree
>>> +	  blob to be loaded when booting from a filesystem.
>>> +
>>> +config K3_SYSFW_IMAGE_MMCSD_RAW_MODE_SECT
>>> +	hex "MMC sector to load SYSFW firmware and configuration blob from"
>>> +	depends on K3_LOAD_SYSFW && SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
>>> +	default 0x3600
>>> +	help
>>> +	  Address on the MMC to load the combined System Firmware and
>>> +	  configuration image tree blob from, when the MMC is being used
>>> +	  in raw mode. Units: MMC sectors (1 sector = 512 bytes).
>>> +
>>> +config K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART
>>> +	hex "MMC partition to load SYSFW firmware and configuration blob from"
>>> +	depends on K3_LOAD_SYSFW && SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
>>> +	default 2
>>> +	help
>>> +	  Partition on the MMC to the combined System Firmware and configuration
>>> +	  image tree blob from, when the MMC is being used in raw mode.
>>> +
>>> +config K3_SYSFW_IMAGE_SIZE_MAX
>>> +	int "Amount of memory dynamically allocated for loading SYSFW blob"
>>> +	depends on K3_LOAD_SYSFW
>>> +	default	269000
>>> +	help
>>> +	  Amount of memory reserved through dynamic allocation at runtime for
>>> +	  loading the combined System Firmware and configuration image tree
>>> +	  blob. Keep it as tight as possible, as this directly affects the
>>> +	  overall SPL memory footprint.
>>> +
>>>    config SYS_K3_SPL_ATF
>>>    	bool "Start Cortex-A from SPL"
>>>    	depends on SPL && CPU_V7R
>>> diff --git a/arch/arm/mach-k3/Makefile b/arch/arm/mach-k3/Makefile
>>> index 0c3a4f7db1..6c895400c2 100644
>>> --- a/arch/arm/mach-k3/Makefile
>>> +++ b/arch/arm/mach-k3/Makefile
>>> @@ -7,4 +7,5 @@ obj-$(CONFIG_SOC_K3_AM6) += am6_init.o
>>>    obj-$(CONFIG_ARM64) += arm64-mmu.o
>>>    obj-$(CONFIG_CPU_V7R) += r5_mpu.o lowlevel_init.o
>>>    obj-$(CONFIG_TI_SECURE_DEVICE) += security.o
>>> +obj-$(CONFIG_K3_LOAD_SYSFW) += sysfw-loader.o
>>>    obj-y += common.o
>>> diff --git a/arch/arm/mach-k3/include/mach/sysfw-loader.h b/arch/arm/mach-k3/include/mach/sysfw-loader.h
>>> new file mode 100644
>>> index 0000000000..36eb265348
>>> --- /dev/null
>>> +++ b/arch/arm/mach-k3/include/mach/sysfw-loader.h
>>> @@ -0,0 +1,12 @@
>>> +/* SPDX-License-Identifier: GPL-2.0+ */
>>> +/*
>>> + * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
>>> + *	Andreas Dannenberg <dannenberg at ti.com>
>>> + */
>>> +
>>> +#ifndef _SYSFW_LOADER_H_
>>> +#define _SYSFW_LOADER_H_
>>> +
>>> +void k3_sysfw_loader(void (*config_pm_done_callback)(void));
>>> +
>>> +#endif
>>> diff --git a/arch/arm/mach-k3/sysfw-loader.c b/arch/arm/mach-k3/sysfw-loader.c
>>> new file mode 100644
>>> index 0000000000..a222266c27
>>> --- /dev/null
>>> +++ b/arch/arm/mach-k3/sysfw-loader.c
>>> @@ -0,0 +1,263 @@
>>> +// SPDX-License-Identifier: GPL-2.0+
>>> +/*
>>> + * K3: System Firmware Loader
>>> + *
>>> + * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
>>> + *	Andreas Dannenberg <dannenberg at ti.com>
>>> + */
>>> +
>>> +#include <common.h>
>>> +#include <spl.h>
>>> +#include <malloc.h>
>>> +#include <remoteproc.h>
>>> +#include <linux/soc/ti/ti_sci_protocol.h>
>>> +#include <asm/arch/sys_proto.h>
>>> +
>>> +/* Name of the FIT image nodes for SYSFW and its config data */
>>> +#define SYSFW_FIRMWARE			"sysfw.bin"
>>> +#define SYSFW_CFG_BOARD			"board-cfg.bin"
>>> +#define SYSFW_CFG_PM			"pm-cfg.bin"
>>> +#define SYSFW_CFG_RM			"rm-cfg.bin"
>>> +#define SYSFW_CFG_SEC			"sec-cfg.bin"
>>> +
>>> +#ifdef CONFIG_SPL_BUILD
>>> +
>>> +static bool sysfw_loaded;
>>> +static void *sysfw_load_address;
>>> +
>>> +/*
>>> + * Populate SPL hook to override the default load address used by the SPL
>>> + * loader function with a custom address for SYSFW loading.
>>> + */
>>> +struct image_header *spl_get_load_buffer(ssize_t offset, size_t size)
>>> +{
>>> +	if (sysfw_loaded)
>>> +		return (struct image_header *)(CONFIG_SYS_TEXT_BASE + offset);
>>> +	else if (sysfw_load_address)
>>> +		return sysfw_load_address;
>>> +	else
>>> +		panic("SYSFW load address not defined!");
>>> +}
>>> +
>>> +/*
>>> + * Populate SPL hook to skip the default SPL loader FIT post-processing steps
>>> + * during SYSFW loading and return to the calling function so we can perform
>>> + * our own custom processing.
>>> + */
>>> +bool spl_load_simple_fit_skip_processing(void)
>>> +{
>>> +	return !sysfw_loaded;
>>> +}
>>> +
>>> +static int fit_get_data_by_name(const void *fit, int images, const char *name,
>>> +				const void **addr, size_t *size)
>>> +{
>>> +	int node_offset;
>>> +
>>> +	node_offset = fdt_subnode_offset(fit, images, name);
>>> +	if (node_offset < 0)
>>> +		return -ENOENT;
>>> +
>>> +	return fit_image_get_data(fit, node_offset, addr, size);
>>> +}
>>> +
>>> +static void k3_sysfw_load_using_fit(void *fit)
>>> +{
>>> +	int images;
>>> +	const void *sysfw_addr;
>>> +	size_t sysfw_size;
>>> +	int ret;
>>> +
>>> +	/* Find the node holding the images information */
>>> +	images = fdt_path_offset(fit, FIT_IMAGES_PATH);
>>> +	if (images < 0)
>>> +		panic("Cannot find /images node (%d)\n", images);
>>> +
>>> +	/* Extract System Firmware (SYSFW) image from FIT */
>>> +	ret = fit_get_data_by_name(fit, images, SYSFW_FIRMWARE,
>>> +				   &sysfw_addr, &sysfw_size);
>>> +	if (ret < 0)
>>> +		panic("Error accessing %s node in FIT (%d)\n", SYSFW_FIRMWARE,
>>> +		      ret);
>>> +
>>> +	/*
>>> +	 * Start up system controller firmware
>>> +	 *
>>> +	 * It is assumed that remoteproc device 0 is the corresponding
>>> +	 * system-controller that runs SYSFW. Make sure DT reflects the same.
>>> +	 */
>>> +	ret = rproc_dev_init(0);
>>> +	if (ret)
>>> +		panic("rproc failed to be initialized (%d)\n", ret);
>>> +
>>> +	ret = rproc_load(0, (ulong)sysfw_addr, (ulong)sysfw_size);
>>> +	if (ret)
>>> +		panic("Firmware failed to start on rproc (%d)\n", ret);
>>> +
>>> +	ret = rproc_start(0);
>>> +	if (ret)
>>> +		panic("Firmware init failed on rproc (%d)\n", ret);
>>> +}
>>> +
>>> +static void k3_sysfw_configure_using_fit(void *fit,
>>> +					 struct ti_sci_handle *ti_sci)
>>> +{
>>> +	struct ti_sci_board_ops *board_ops = &ti_sci->ops.board_ops;
>>> +	int images;
>>> +	const void *cfg_fragment_addr;
>>> +	size_t cfg_fragment_size;
>>> +	int ret;
>>> +
>>> +	/* Find the node holding the images information */
>>> +	images = fdt_path_offset(fit, FIT_IMAGES_PATH);
>>> +	if (images < 0)
>>> +		panic("Cannot find /images node (%d)\n", images);
>>> +
>>> +	/* Extract board configuration from FIT */
>>> +	ret = fit_get_data_by_name(fit, images, SYSFW_CFG_BOARD,
>>> +				   &cfg_fragment_addr, &cfg_fragment_size);
>>> +	if (ret < 0)
>>> +		panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_BOARD,
>>> +		      ret);
>>> +
>>> +	/* Apply board configuration to SYSFW */
>>> +	ret = board_ops->board_config(ti_sci,
>>> +				      (u64)(u32)cfg_fragment_addr,
>>> +				      (u32)cfg_fragment_size);
>>> +	if (ret)
>>> +		panic("Failed to set board configuration (%d)\n", ret);
>>> +
>>> +	/* Extract power/clock (PM) specific configuration from FIT */
>>> +	ret = fit_get_data_by_name(fit, images, SYSFW_CFG_PM,
>>> +				   &cfg_fragment_addr, &cfg_fragment_size);
>>> +	if (ret < 0)
>>> +		panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_PM,
>>> +		      ret);
>>> +
>>> +	/* Apply power/clock (PM) specific configuration to SYSFW */
>>> +	ret = board_ops->board_config_pm(ti_sci,
>>> +					 (u64)(u32)cfg_fragment_addr,
>>> +					 (u32)cfg_fragment_size);
>>> +	if (ret)
>>> +		panic("Failed to set board PM configuration (%d)\n", ret);
>>> +
>>> +	/* Extract resource management (RM) specific configuration from FIT */
>>> +	ret = fit_get_data_by_name(fit, images, SYSFW_CFG_RM,
>>> +				   &cfg_fragment_addr, &cfg_fragment_size);
>>> +	if (ret < 0)
>>> +		panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_RM,
>>> +		      ret);
>>> +
>>> +	/* Apply resource management (RM) configuration to SYSFW */
>>> +	ret = board_ops->board_config_rm(ti_sci,
>>> +					 (u64)(u32)cfg_fragment_addr,
>>> +					 (u32)cfg_fragment_size);
>>> +	if (ret)
>>> +		panic("Failed to set board RM configuration (%d)\n", ret);
>>> +
>>> +	/* Extract security specific configuration from FIT */
>>> +	ret = fit_get_data_by_name(fit, images, SYSFW_CFG_SEC,
>>> +				   &cfg_fragment_addr, &cfg_fragment_size);
>>> +	if (ret < 0)
>>> +		panic("Error accessing %s node in FIT (%d)\n", SYSFW_CFG_SEC,
>>> +		      ret);
>>> +
>>> +	/* Apply security configuration to SYSFW */
>>> +	ret = board_ops->board_config_security(ti_sci,
>>> +					       (u64)(u32)cfg_fragment_addr,
>>> +					       (u32)cfg_fragment_size);
>>> +	if (ret)
>>> +		panic("Failed to set board security configuration (%d)\n",
>>> +		      ret);
>>> +}
>>> +
>>> +void k3_sysfw_loader(void (*config_pm_done_callback)(void))
>>> +{
>>> +	struct spl_image_info spl_image = { 0 };
>>> +	struct spl_boot_device bootdev = { 0 };
>>> +	struct ti_sci_handle *ti_sci;
>>> +	int ret;
>>> +
>>> +	/* Reserve a block of aligned memory for loading the SYSFW image */
>>> +	sysfw_load_address = memalign(ARCH_DMA_MINALIGN,
>>> +				      CONFIG_K3_SYSFW_IMAGE_SIZE_MAX);
>>> +	if (!sysfw_load_address)
>>> +		panic("Error allocating %u bytes of memory for SYSFW image\n",
>>> +		      CONFIG_K3_SYSFW_IMAGE_SIZE_MAX);
>>> +
>>> +	debug("%s: allocated %u bytes at 0x%p\n", __func__,
>>> +	      CONFIG_K3_SYSFW_IMAGE_SIZE_MAX, sysfw_load_address);
>>> +
>>> +	/* Set load address for legacy modes that bypass spl_get_load_buffer */
>>> +	spl_image.load_addr = (uintptr_t)sysfw_load_address;
>>> +
>>> +	bootdev.boot_device = spl_boot_device();
>>> +
>>> +	/* Load combined System Controller firmware and config data image */
>>> +	switch (bootdev.boot_device) {
>>> +#if CONFIG_IS_ENABLED(MMC_SUPPORT)
>>> +	case BOOT_DEVICE_MMC1:
>>> +	case BOOT_DEVICE_MMC2:
>>> +	case BOOT_DEVICE_MMC2_2:
>>> +		ret = spl_mmc_load(&spl_image, &bootdev,
>>> +#ifdef CONFIG_K3_SYSFW_IMAGE_NAME
>>> +				   CONFIG_K3_SYSFW_IMAGE_NAME,
>>> +#else
>>> +				   NULL,
>>> +#endif
>>> +#ifdef CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART
>>> +				   CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_PART,
>>> +#else
>>> +				   0,
>>> +#endif
>>> +#ifdef CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_SECT
>>> +				   CONFIG_K3_SYSFW_IMAGE_MMCSD_RAW_MODE_SECT);
>>> +#else
>>> +				   0);
>>> +#endif
>>> +		break;
>>> +#endif
>>> +	default:
>>> +		panic("Loading SYSFW image from device %u not supported!\n",
>>> +		      bootdev.boot_device);
>>> +	}
>>> +
>>> +	if (ret)
>>> +		panic("Error %d occurred during loading SYSFW image!\n", ret);
>>> +
>>> +	/*
>>> +	 * Now that SYSFW got loaded set helper flag to restore regular SPL
>>> +	 * loader behavior so we can later boot into the next stage as expected.
>>> +	 */
>>> +	sysfw_loaded = true;
>>> +
>>> +	/* Ensure the SYSFW image is in FIT format */
>>> +	if (image_get_magic((const image_header_t *)sysfw_load_address) !=
>>> +	    FDT_MAGIC)
>>> +		panic("SYSFW image not in FIT format!\n");
>>> +
>>> +	/* Extract and start SYSFW */
>>> +	k3_sysfw_load_using_fit(sysfw_load_address);
>>> +
>>> +	/* Get handle for accessing SYSFW services */
>>> +	ti_sci = get_ti_sci_handle();
>>> +
>>> +	/* Parse and apply the different SYSFW configuration fragments */
>>> +	k3_sysfw_configure_using_fit(sysfw_load_address, ti_sci);
>>> +
>>> +	/*
>>> +	 * Now that all clocks and PM aspects are setup, invoke a user-
>>> +	 * provided callback function. Usually this callback would be used
>>> +	 * to setup or re-configure the U-Boot console UART.
>>> +	 */
>>> +	if (config_pm_done_callback)
>>> +		config_pm_done_callback();
>>> +
>>> +	/* Output System Firmware version info */
>>> +	printf("SYSFW ABI: %d.%d (firmware rev 0x%04x '%.*s')\n",
>>> +	       ti_sci->version.abi_major, ti_sci->version.abi_minor,
>>> +	       ti_sci->version.firmware_revision,
>>> +	       sizeof(ti_sci->version.firmware_description),
>>> +	       ti_sci->version.firmware_description);
>>> +}
>>> +#endif
>>>


More information about the U-Boot mailing list