[U-Boot] Pull request: u-boot-net.git master
Joe Hershberger
joe.hershberger at ni.com
Wed May 8 22:24:30 UTC 2019
On Tue, May 7, 2019 at 5:15 PM Joe Hershberger <joe.hershberger at ni.com> wrote:
>
> Hi Tom,
>
> The following changes since commit 8d7f06bbbef16f172cd5e9c4923cdcebe16b8980:
>
> I rebased on your master and built for BB Black. DHCP seems to work fine.
> MLO also now fits again.
>
> Merge branch 'master' of git://git.denx.de/u-boot-sh (2019-05-07 09:38:00 -0400)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-net.git master
>
> for you to fetch changes up to 8d0c6858455e89b089222a08d55ff711681ca011:
>
> net: phy: micrel: Find Micrel PHY node correctly (2019-05-07 14:51:55 -0500)
>
> ----------------------------------------------------------------
> Carlo Caione (4):
> net: phy: Add generic helpers to access MMD PHY registers
> net: phy: ti: use generic helpers to access MMD registers
> cmd: mdio: Switch to generic helpers when accessing the registers
> net: phy: realtek: Introduce quirk to mark RXC not stoppable
>
> James Byrne (2):
> net: phy: micrel: Use correct skew values on KSZ9021
> net: phy: micrel: Find Micrel PHY node correctly
>
> Murali Karicheri (2):
> ARM: k2g-gp-evm: update to rgmii pinmux configuration
> ARM: k2g-ice: Add pinmux support for rgmii interface
>
> Pankaj Bansal (1):
> drivers: net: ldpaa_eth: fix resource leak
>
> Siva Durga Prasad Paladugu (2):
> net: phy: Reloc next and prev pointers inside phy_drivers
> net: phy: Fix return value check phy_probe
>
> Valentin-catalin Neacsu (1):
> net: phy: aquantia: Set only autoneg on in register 4.c441
>
> Vladimir Oltean (6):
> net: phy: ar803x: Address packet drops at low traffic rate due to SmartEEE feature
> net: phy: ar803x: Make RGMII Tx delays actually configurable for AR8035
> net: phy: ar803x: Use common functions for RGMII internal delays
> net: phy: ar803x: Clarify the configuration of the CLK_25M output pin
> net: phy: ar803x: Explicitly disable RGMII delays
Tom, this [1] is the patch that is breaking the evm. It doesn't affect
BB Black because it uses an SMSC phy, where as this evm uses an
AR8031/AR8033.
Is it possible the device tree [2] is wrong for the board? It lists
'phy-mode = "rgmii-txid";', so that means that with this patch the RX
delay is now being disabled.
Any thoughts, Vladimir?
Thanks,
-Joe
[1] b3224e0f7e - "net: phy: ar803x: Explicitly disable RGMII delays"
[2] arch/arm/dts/am335x-evm.dts
> net: phy: ar803x: Clarify the intention of ar8021_config
>
> arch/arm/dts/sama5d3xcm.dtsi | 32 +++---
> arch/arm/dts/sama5d3xcm_cmp.dtsi | 32 +++---
> arch/arm/dts/socfpga_arria5_socdk.dts | 4 +-
> arch/arm/dts/socfpga_cyclone5_is1.dts | 4 +-
> arch/arm/dts/socfpga_cyclone5_socdk.dts | 4 +-
> arch/arm/dts/socfpga_cyclone5_sockit.dts | 4 +-
> arch/arm/dts/socfpga_cyclone5_vining_fpga.dts | 4 +-
> board/ti/ks2_evm/mux-k2g.h | 36 +++----
> cmd/mdio.c | 27 +++--
> doc/device-tree-bindings/net/micrel-ksz90x1.txt | 27 +++++
> drivers/net/ldpaa_eth/ldpaa_eth.c | 1 +
> drivers/net/phy/Kconfig | 41 ++++++++
> drivers/net/phy/aquantia.c | 7 +-
> drivers/net/phy/atheros.c | 128 ++++++++++++++++-------
> drivers/net/phy/micrel_ksz90x1.c | 24 ++++-
> drivers/net/phy/phy.c | 21 +++-
> drivers/net/phy/realtek.c | 19 ++++
> drivers/net/phy/ti.c | 130 +++++-------------------
> include/phy.h | 70 +++++++++++++
> 19 files changed, 394 insertions(+), 221 deletions(-)
>
> Thanks!
> -Joe
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot
More information about the U-Boot
mailing list