[U-Boot] [PATCH v2 1/2] mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled

[Yinbo Zhu]

From: Yangbo Lu <yangbo.lu at nxp.com>

u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.

config BLK
	bool "Support block devices"
	depends on DM
	default y if DM_MMC

When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.

Signed-off-by: Yangbo Lu <yangbo.lu at nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu at nxp.com>
---
Change in v2:
		use existing bit define instead of magic number	
		remove the spl patches

 drivers/mmc/fsl_esdhc.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c
index 9e34557d16..f1d67657fa 100644
--- a/drivers/mmc/fsl_esdhc.c
+++ b/drivers/mmc/fsl_esdhc.c
@@ -25,6 +25,10 @@
 #include <asm-generic/gpio.h>
 #include <dm/pinctrl.h>
 
+#if !CONFIG_IS_ENABLED(BLK)
+#include "mmc_private.h"
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 #define SDHCI_IRQ_EN_BITS		(IRQSTATEN_CC | IRQSTATEN_TC | \
@@ -34,6 +38,7 @@ DECLARE_GLOBAL_DATA_PTR;
 				IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \
 				IRQSTATEN_DINT)
 #define MAX_TUNING_LOOP 40
+#define ESDHC_DRIVER_STAGE_VALUE 0xffffffff
 
 struct fsl_esdhc {
 	uint    dsaddr;		/* SDMA system address register */
@@ -1448,6 +1453,9 @@ static int fsl_esdhc_probe(struct udevice *dev)
 	fdt_addr_t addr;
 	unsigned int val;
 	struct mmc *mmc;
+#if !CONFIG_IS_ENABLED(BLK)
+	struct blk_desc *bdesc;
+#endif
 	int ret;
 
 	addr = dev_read_addr(dev);
@@ -1576,6 +1584,26 @@ static int fsl_esdhc_probe(struct udevice *dev)
 	mmc = &plat->mmc;
 	mmc->cfg = &plat->cfg;
 	mmc->dev = dev;
+#if !CONFIG_IS_ENABLED(BLK)
+	mmc->priv = priv;
+
+	/* Setup dsr related values */
+	mmc->dsr_imp = 0;
+	mmc->dsr = ESDHC_DRIVER_STAGE_VALUE;
+	/* Setup the universal parts of the block interface just once */
+	bdesc = mmc_get_blk_desc(mmc);
+	bdesc->if_type = IF_TYPE_MMC;
+	bdesc->removable = 1;
+	bdesc->devnum = mmc_get_next_devnum();
+	bdesc->block_read = mmc_bread;
+	bdesc->block_write = mmc_bwrite;
+	bdesc->block_erase = mmc_berase;
+
+	/* setup initial part type */
+	bdesc->part_type = mmc->cfg->part_type;
+	mmc_list_add(mmc);
+#endif
+
 	upriv->mmc = mmc;
 
 	return esdhc_init_common(priv, mmc);
-- 
2.17.1