[U-Boot] [RFC 08/11] armV7R: K3: am654: Load SYSFW binary and config from boot media

[Andreas Dannenberg]

Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.

Signed-off-by: Andreas Dannenberg <dannenberg at ti.com>
---
 arch/arm/mach-k3/am6_init.c | 27 ++++++++++++++++++++++++++-
 board/ti/am65x/Kconfig      |  1 +
 2 files changed, 27 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-k3/am6_init.c b/arch/arm/mach-k3/am6_init.c
index 22477efa5b..f50eded03f 100644
--- a/arch/arm/mach-k3/am6_init.c
+++ b/arch/arm/mach-k3/am6_init.c
@@ -10,8 +10,11 @@
 #include <asm/io.h>
 #include <spl.h>
 #include <asm/arch/hardware.h>
+#include <asm/arch/sysfw-loader.h>
 #include "common.h"
 #include <dm.h>
+#include <dm/uclass-internal.h>
+#include <dm/pinctrl.h>
 
 #ifdef CONFIG_SPL_BUILD
 static void mmr_unlock(u32 base, u32 partition)
@@ -63,7 +66,7 @@ static void store_boot_index_from_rom(void)
 
 void board_init_f(ulong dummy)
 {
-#if defined(CONFIG_K3_AM654_DDRSS)
+#if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM654_DDRSS)
 	struct udevice *dev;
 	int ret;
 #endif
@@ -90,8 +93,30 @@ void board_init_f(ulong dummy)
 	/* Init DM early in-order to invoke system controller */
 	spl_early_init();
 
+#ifdef CONFIG_K3_LOAD_SYSFW
+	/*
+	 * Process pinctrl for the serial0 a.k.a. WKUP_UART0 module and continue
+	 * regardless of the result of pinctrl. Do this without probing the
+	 * device, but instead by searching the device that would request the
+	 * given sequence number if probed. The UART will be used by the system
+	 * firmware (SYSFW) image for various purposes and SYSFW depends on us
+	 * to initialize its pin settings.
+	 */
+	ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, true, &dev);
+	if (!ret)
+		pinctrl_select_state(dev, "default");
+
+	/*
+	 * Load, start up, and configure system controller firmware. Provide
+	 * the U-Boot console init function to the SYSFW post-PM configuration
+	 * callback hook, effectively switching on (or over) the console
+	 * output.
+	 */
+	k3_sysfw_loader(preloader_console_init);
+#else
 	/* Prepare console output */
 	preloader_console_init();
+#endif
 
 #ifdef CONFIG_K3_AM654_DDRSS
 	ret = uclass_get_device(UCLASS_RAM, 0, &dev);
diff --git a/board/ti/am65x/Kconfig b/board/ti/am65x/Kconfig
index 98172c28f5..60bb834aca 100644
--- a/board/ti/am65x/Kconfig
+++ b/board/ti/am65x/Kconfig
@@ -18,6 +18,7 @@ config TARGET_AM654_R5_EVM
 	select CPU_V7R
 	select SYS_THUMB_BUILD
 	select SOC_K3_AM6
+	select K3_LOAD_SYSFW
 	select K3_AM654_DDRSS
 	imply SYS_K3_SPL_ATF
 
-- 
2.17.1