[U-Boot] [PATCH 4/8] ARM: imx: vining2000: Convert MMC and block to DM

[Marek Vasut]

Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.

Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Fabio Estevam <fabio.estevam at nxp.com>
Cc: Silvio Fricke <silvio.fricke at softing.com>
Cc: Stefano Babic <sbabic at denx.de>
---
 arch/arm/dts/imx6sx-softing-vining-2000.dts |  5 ++
 board/softing/vining_2000/vining_2000.c     | 77 ---------------------
 configs/vining_2000_defconfig               |  2 +-
 3 files changed, 6 insertions(+), 78 deletions(-)

diff --git a/arch/arm/dts/imx6sx-softing-vining-2000.dts b/arch/arm/dts/imx6sx-softing-vining-2000.dts
index 2bc51623a8..371890ff60 100644
--- a/arch/arm/dts/imx6sx-softing-vining-2000.dts
+++ b/arch/arm/dts/imx6sx-softing-vining-2000.dts
@@ -16,6 +16,11 @@
 	model = "Softing VIN|ING 2000";
 	compatible = "samtec,imx6sx-vining-2000", "fsl,imx6sx";
 
+	aliases {
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+	};
+
 	chosen {
 		stdout-path = &uart1;
 	};
diff --git a/board/softing/vining_2000/vining_2000.c b/board/softing/vining_2000/vining_2000.c
index f0313b06fb..9ab7fbeddf 100644
--- a/board/softing/vining_2000/vining_2000.c
+++ b/board/softing/vining_2000/vining_2000.c
@@ -76,30 +76,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
-static iomux_v3_cfg_t const usdhc2_pads[] = {
-	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
-	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
-	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
-	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_RESET_B__USDHC4_RESET_B | MUX_PAD_CTRL(USDHC_RESET_CTRL),
-};
-
 static iomux_v3_cfg_t const fec1_pads[] = {
 	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
@@ -449,59 +425,6 @@ int board_early_init_f(void)
 	return 0;
 }
 
-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
-	{USDHC4_BASE_ADDR, 0, 8},
-	{USDHC2_BASE_ADDR, 0, 4},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
-	if (cfg->esdhc_base == USDHC4_BASE_ADDR)
-		return 1;
-	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
-		return !gpio_get_value(USDHC2_CD_GPIO);
-
-	return -EINVAL;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	int ret;
-
-	/*
-	 * According to the board_mmc_init() the following map is done:
-	 * (U-Boot device node)    (Physical Port)
-	 * mmc0                    USDHC4
-	 * mmc1                    USDHC2
-	 */
-	imx_iomux_v3_setup_multiple_pads(
-		usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
-	imx_iomux_v3_setup_multiple_pads(
-		usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-	gpio_direction_input(USDHC2_CD_GPIO);
-	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
-	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-	if (ret) {
-		printf("Warning: failed to initialize USDHC4\n");
-		return ret;
-	}
-
-	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
-	if (ret) {
-		printf("Warning: failed to initialize USDHC2\n");
-		return ret;
-	}
-
-	return 0;
-}
-
 int board_init(void)
 {
 	/* Address of boot parameters */
diff --git a/configs/vining_2000_defconfig b/configs/vining_2000_defconfig
index 01736823b8..2bd88149be 100644
--- a/configs/vining_2000_defconfig
+++ b/configs/vining_2000_defconfig
@@ -38,6 +38,7 @@ CONFIG_EFI_PARTITION=y
 CONFIG_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="imx6sx-softing-vining-2000"
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
+CONFIG_DM_MMC=y
 CONFIG_SUPPORT_EMMC_RPMB=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_FSL_ESDHC=y
@@ -47,6 +48,5 @@ CONFIG_PCI=y
 CONFIG_PINCTRL=y
 CONFIG_PINCTRL_IMX6=y
 CONFIG_USB=y
-CONFIG_USB_STORAGE=y
 CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
-- 
2.20.1