[U-Boot] [PATCH v2 00/18] Improvement for the DWC3 USB generic driver and fixes for the K2 platforms

[Siva Durga Prasad Paladugu]

Hi,

-----Original Message-----
From: Marek Vasut [mailto:marex at denx.de] 
Sent: Tuesday, May 21, 2019 6:14 PM
To: Siva Durga Prasad Paladugu <sivadur at xilinx.com>; Jean-Jacques Hiblot <jjhiblot at ti.com>; lukma at denx.de
Cc: Marcel Ziswiler <marcel.ziswiler at toradex.com>; u-boot at lists.denx.de; Miquel Raynal <miquel.raynal at bootlin.com>; Stefan Roese <sr at denx.de>; Tom Rini <trini at konsulko.com>; Ryder Lee <ryder.lee at mediatek.com>; Heinrich Schuchardt <xypron.glpk at gmx.de>; Michal Simek <michals at xilinx.com>; Krzysztof Kozlowski <krzk at kernel.org>; Maxime Ripard <maxime.ripard at bootlin.com>; Sven Schwermer <sven at svenschwermer.de>; Ramon Fried <ramon.fried at gmail.com>; Eugeniu Rosca <roscaeugeniu at gmail.com>; Vitaly Andrianov <vitalya at ti.com>; Joe Hershberger <joe.hershberger at ni.com>; Tom Warren <twarren at nvidia.com>
Subject: Re: [U-Boot] [PATCH v2 00/18] Improvement for the DWC3 USB generic driver and fixes for the K2 platforms

On 5/21/19 1:36 PM, Siva Durga Prasad Paladugu wrote:
> Hi,

Hi,

> Tested the series with one out of tree patch(https://marc.info/?l=u-boot&m=155409909828219 ) on Xilinx ZynqMP and it looks fine.
> We may need to finalize on https://marc.info/?l=u-boot&m=155409909828219 as well.
> 
> U-Boot 2019.04-rc4-00065-g5063fa3-dirty (May 21 2019 - 16:58:34 +0530)

Does it still work on current master (2019.07-rc) ? Testing a patch on top of rc version of previous release is not really helpful.

[...]

Its same with latest too.

U-Boot 2019.07-rc2-00182-g29792e4-dirty (May 22 2019 - 11:21:25 +0530)

Model: ZynqMP ZCU102 Rev1.0
Board: Xilinx ZynqMP
DRAM:  4 GiB
EL Level:       EL2
Chip ID:        zu9eg
MMC:   mmc at ff170000: 0
Loading Environment from FAT... *** Warning - bad CRC, using default environment

In:    serial at ff000000
Out:   serial at ff000000
Err:   serial at ff000000
Bootmode: JTAG_MODE
Reset reason:   EXTERNAL 
Net:   ZYNQ GEM: ff0e0000, phyaddr c, interface rgmii-id

Warning: ethernet at ff0e0000 (eth0) using random MAC address - ca:f4:c2:4a:b8:df
eth0: ethernet at ff0e0000
Hit any key to stop autoboot:  0 
ZynqMP> usb start
starting USB...
Bus dwc3 at fe200000: Register 2000440 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus dwc3 at fe200000 for devices... 2 USB Device(s) found
       scanning usb for storage devices... 1 Storage Device(s) found
ZynqMP> ls ubs 0
ZynqMP> ls usb 0
  5242880   dummy.bin
 133849600   Image

2 file(s), 0 dir(s)

ZynqMP> load usb 0 100000 dummy.bin
5242880 bytes read in 55 ms (90.9 MiB/s)
ZynqMP>

Thanks,
Siva

--
Best regards,
Marek Vasut