[U-Boot] [linux-sunxi] [PATCH v4] sun8i: h3: Add support for the Beelink-x2 STB

Code Kipper codekipper at gmail.com
Sun May 26 14:52:32 UTC 2019


On Sun, 26 May 2019 at 14:13, Jernej Škrabec <jernej.skrabec at gmail.com> wrote:
>
> Hi!
>
> Dne nedelja, 26. maj 2019 ob 08:28:41 CEST je codekipper at gmail.com napisal(a):
> > From: Marcus Cooper <codekipper at gmail.com>
> >
> > The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
> > 2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
> > SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
> > dual colour LED and an optical S/PDIF connector.
> >
> > Signed-off-by: Marcus Cooper <codekipper at gmail.com>
> > ---
> > Changes in v4:
> > - updated dts to reflex current linux kernel status
> >
> > Changes in v3:
> > - Removed incorrect commit author
> > - Included v1-v2 change info
> >
> > Changes in v2:
> > - updated dts to reflex current linux kernel status
> > ---
> >  arch/arm/dts/Makefile                |   1 +
> >  arch/arm/dts/sun8i-h3-beelink-x2.dts | 216 +++++++++++++++++++++++++++
> >  board/sunxi/MAINTAINERS              |   5 +
> >  configs/beelink_x2_defconfig         |  19 +++
> >  4 files changed, 241 insertions(+)
> >  create mode 100644 arch/arm/dts/sun8i-h3-beelink-x2.dts
> >  create mode 100644 configs/beelink_x2_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index 83058c4452..716108dd2e 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -472,6 +472,7 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
> >       sun8i-h2-plus-orangepi-r1.dtb \
> >       sun8i-h2-plus-orangepi-zero.dtb \
> >       sun8i-h3-bananapi-m2-plus.dtb \
> > +     sun8i-h3-beelink-x2.dtb \
> >       sun8i-h3-libretech-all-h3-cc.dtb \
> >       sun8i-h3-nanopi-m1.dtb \
> >       sun8i-h3-nanopi-m1-plus.dtb \
> > diff --git a/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > b/arch/arm/dts/sun8i-h3-beelink-x2.dts new file mode 100644
> > index 0000000000..25540b7694
> > --- /dev/null
> > +++ b/arch/arm/dts/sun8i-h3-beelink-x2.dts
> > @@ -0,0 +1,216 @@
> > +/*
> > + * Copyright (C) 2017 Marcus Cooper <codekipper at gmail.com>
> > + *
> > + * This file is dual-licensed: you can use it either under the terms
> > + * of the GPL or the X11 license, at your option. Note that this dual
> > + * licensing only applies to this file, and not this project as a
> > + * whole.
> > + *
> > + *  a) This file is free software; you can redistribute it and/or
> > + *     modify it under the terms of the GNU General Public License as
> > + *     published by the Free Software Foundation; either version 2 of the
> > + *     License, or (at your option) any later version.
> > + *
> > + *     This file is distributed in the hope that it will be useful,
> > + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + *     GNU General Public License for more details.
> > + *
> > + * Or, alternatively,
> > + *
> > + *  b) Permission is hereby granted, free of charge, to any person
> > + *     obtaining a copy of this software and associated documentation
> > + *     files (the "Software"), to deal in the Software without
> > + *     restriction, including without limitation the rights to use,
> > + *     copy, modify, merge, publish, distribute, sublicense, and/or
> > + *     sell copies of the Software, and to permit persons to whom the
> > + *     Software is furnished to do so, subject to the following
> > + *     conditions:
> > + *
> > + *     The above copyright notice and this permission notice shall be
> > + *     included in all copies or substantial portions of the Software.
> > + *
> > + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> > + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> > + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> > + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> > + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> > + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> > + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> > + *     OTHER DEALINGS IN THE SOFTWARE.
> > + */
> > +
> > +/dts-v1/;
> > +#include "sun8i-h3.dtsi"
> > +#include "sunxi-common-regulators.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > +     model = "Beelink X2";
> > +     compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
> > +
> > +     aliases {
> > +             serial0 = &uart0;
> > +             ethernet0 = &emac;
> > +             ethernet1 = &sdiowifi;
> > +     };
> > +
> > +     chosen {
> > +             stdout-path = "serial0:115200n8";
> > +     };
> > +
> > +     connector {
> > +             compatible = "hdmi-connector";
> > +             type = "a";
> > +
> > +             port {
> > +                     hdmi_con_in: endpoint {
> > +                             remote-endpoint = <&hdmi_out_con>;
> > +                     };
> > +             };
> > +     };
> > +
> > +     leds {
> > +             compatible = "gpio-leds";
> > +
> > +             blue {
> > +                     label = "beelink-x2:blue:pwr";
> > +                     gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /*
> PL10 */
> > +                     default-state = "on";
> > +             };
> > +
> > +             red {
> > +                     label = "beelink-x2:red:standby";
> > +                     gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15
> */
> > +             };
> > +     };
> > +
> > +     wifi_pwrseq: wifi_pwrseq {
> > +             compatible = "mmc-pwrseq-simple";
> > +             reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
> > +     };
> > +
> > +     sound_spdif {
> > +             compatible = "simple-audio-card";
> > +             simple-audio-card,name = "On-board SPDIF";
> > +
> > +             simple-audio-card,cpu {
> > +                     sound-dai = <&spdif>;
> > +             };
> > +
> > +             simple-audio-card,codec {
> > +                     sound-dai = <&spdif_out>;
> > +             };
> > +     };
> > +
> > +     spdif_out: spdif-out {
> > +             #sound-dai-cells = <0>;
> > +             compatible = "linux,spdif-dit";
> > +     };
> > +};
> > +
> > +&de {
> > +     status = "okay";
> > +};
> > +
> > +&ehci0 {
> > +     status = "okay";
> > +};
> > +
> > +&ehci1 {
> > +     status = "okay";
> > +};
> > +
> > +&emac {
> > +     phy-handle = <&int_mii_phy>;
> > +     phy-mode = "mii";
> > +     allwinner,leds-active-low;
> > +     status = "okay";
> > +};
> > +
> > +&hdmi {
> > +     status = "okay";
> > +};
> > +
> > +&hdmi_out {
> > +     hdmi_out_con: endpoint {
> > +             remote-endpoint = <&hdmi_con_in>;
> > +     };
> > +};
> > +
> > +&ir {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&ir_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&mmc0 {
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <4>;
> > +     cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
> > +     status = "okay";
> > +};
> > +
> > +&mmc1 {
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <4>;
> > +     non-removable;
> > +     status = "okay";
> > +
> > +     /*
> > +      * Explicitly define the sdio device, so that we can add an ethernet
> > +      * alias for it (which e.g. makes u-boot set a mac-address).
> > +      */
> > +     sdiowifi: sdio_wifi at 1 {
> > +             reg = <1>;
> > +     };
> > +};
> > +
> > +&mmc2 {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&mmc2_8bit_pins>;
> > +     vmmc-supply = <&reg_vcc3v3>;
> > +     bus-width = <8>;
> > +     non-removable;
> > +     cap-mmc-hw-reset;
> > +     status = "okay";
> > +};
> > +
> > +&ohci0 {
> > +     status = "okay";
> > +};
> > +
> > +&ohci1 {
> > +     status = "okay";
> > +};
> > +
> > +&reg_usb0_vbus {
> > +     gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
> > +     status = "okay";
> > +};
> > +
> > +&spdif {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&spdif_tx_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&uart0 {
> > +     pinctrl-names = "default";
> > +     pinctrl-0 = <&uart0_pins_a>;
> > +     status = "okay";
> > +};
> > +
> > +&usb_otg {
> > +     dr_mode = "otg";
> > +     status = "okay";
> > +};
> > +
> > +&usbphy {
> > +     /* USB VBUS is always on except for the OTG port */
> > +     status = "okay";
> > +     usb0_id_det-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA07 */
> > +     usb0_vbus-supply = <&reg_usb0_vbus>;
> > +};
> > diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
> > index bdd1854197..28f2bece40 100644
> > --- a/board/sunxi/MAINTAINERS
> > +++ b/board/sunxi/MAINTAINERS
> > @@ -172,6 +172,11 @@ S:       Maintained
> >  F:   configs/beelink_gs1_defconfig
> >  F:   arch/arm/dts/sun50i-h6-beelink-gs1.dts
> >
> > +BEELINK X2 BOARD
> > +M:   Marcus Cooper <codekipper at gmail.com>
> > +S:   Maintained
> > +F:   configs/beelink_x2_defconfig
> > +
> >  COLOMBUS BOARD
> >  M:   Maxime Ripard <maxime.ripard at bootlin.com>
> >  S:   Maintained
> > diff --git a/configs/beelink_x2_defconfig b/configs/beelink_x2_defconfig
> > new file mode 100644
> > index 0000000000..6508e470a0
> > --- /dev/null
> > +++ b/configs/beelink_x2_defconfig
> > @@ -0,0 +1,19 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_SPL=y
> > +CONFIG_MACH_SUN8I_H3=y
> > +CONFIG_DRAM_CLK=624
> > +CONFIG_DRAM_ZQ=3881979
> > +CONFIG_DRAM_ODT_EN=y
> > +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-beelink-x2"
> > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> > +CONFIG_CONSOLE_MUX=y
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +# CONFIG_CMD_FLASH is not set
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +# CONFIG_SPL_EFI_PARTITION is not set
> > +CONFIG_SUN8I_EMAC=y
> > +CONFIG_SY8106A_POWER=y
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
>
> I think you should add:
> CONFIG_SPL_TEXT_BASE=0x60
>
> due to following commit:
> http://git.denx.de/?p=u-boot/u-boot-sunxi.git;a=commit;h=f89d6133ee
ACK, arrgghh I thought the sunxi-next branch was misbehaving. Now
boots ontop of master,
CK
>
> Best regards,
> Jernej
>
>
>


More information about the U-Boot mailing list