[U-Boot] [PATCH 3/3] usb: musb-new: omap2430: Fix compilation warning with USB_MUSB_GADGET
Marek Vasut
marek.vasut at gmail.com
Tue May 28 23:27:42 UTC 2019
On 5/29/19 1:16 AM, Derald Woods wrote:
> On Tue, May 28, 2019 at 4:16 PM Marek Vasut <marek.vasut at gmail.com> wrote:
>>
>> On 5/28/19 4:22 AM, Derald D. Woods wrote:
>>> This commit addresses the following warning, when _NOT_ USB_MUSB_HOST:
>>>
>>> [...]
>>> CC drivers/usb/gadget/f_mass_storage.o
>>> CC drivers/usb/musb-new/omap2430.o
>>> CC drivers/usb/gadget/f_fastboot.o
>>> CC env/common.o
>>> CC env/env.o
>>> /src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’:
>>> /src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion]
>>> ret = musb_register(&platdata->plat,
>>> ^
>>> LD drivers/usb/host/built-in.o
>>> CC drivers/usb/gadget/f_sdp.o
>>> CC fs/ext4/ext4fs.o
>>> [...]
Skip to the end first
>>> Signed-off-by: Derald D. Woods <woods.technical at gmail.com>
>>> ---
>>> drivers/usb/musb-new/omap2430.c | 8 ++++++--
>>> 1 file changed, 6 insertions(+), 2 deletions(-)
>>>
>>> diff --git a/drivers/usb/musb-new/omap2430.c b/drivers/usb/musb-new/omap2430.c
>>> index 32743aa72c..cca1653f1e 100644
>>> --- a/drivers/usb/musb-new/omap2430.c
>>> +++ b/drivers/usb/musb-new/omap2430.c
>>> @@ -215,11 +215,13 @@ static int omap2430_musb_probe(struct udevice *dev)
>>> {
>>> #ifdef CONFIG_USB_MUSB_HOST
>>> struct musb_host_data *host = dev_get_priv(dev);
>>> +#else
>>> + struct musb *musbp;
Drop this hunk
>>> #endif
>>> struct omap2430_musb_platdata *platdata = dev_get_platdata(dev);
>>> struct usb_bus_priv *priv = dev_get_uclass_priv(dev);
>>> struct omap_musb_board_data *otg_board_data;
>>> - int ret;
>>> + int ret = 0;
>>> void *base = dev_read_addr_ptr(dev);
>>>
>>> priv->desc_before_addr = true;
>>> @@ -236,9 +238,11 @@ static int omap2430_musb_probe(struct udevice *dev)
>>>
>>> ret = musb_lowlevel_init(host);
>>> #else
>>> - ret = musb_register(&platdata->plat,
>>> + musbp = musb_register(&platdata->plat,
Replace musbp with host->host
>>> (struct device *)otg_board_data,
>>> platdata->base);
>>> + if (IS_ERR_OR_NULL(musbp))
here too
>>> + return -EINVAL;
>>
>> For example the pic32 glue code holds the musb_host_data in private data
>> , so it can call musb_stop() in .remove callback . Can you do the same?
>>
>
> This was just a non-structural change to eliminate a compiler warning.
> I agree that other things can/should be done with this driver. That
> work would be outside of what I was trying to accomplsh here, at the
> moment.
See above, I believe that should fix the problem _and_ not crash in the
.remove() .
--
Best regards,
Marek Vasut
More information about the U-Boot
mailing list