[U-Boot] [v3, 2/5] mmc: split fsl_esdhc driver for i.MX
Lukasz Majewski
lukma at denx.de
Wed May 29 06:29:35 UTC 2019
Hi Y.b. Lu,
> The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
> initially. The later QoriQ series PowerPC processors (which were
> evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
> i.MX series processors were using this driver for their eSDHCs too.
>
> For the two series processors, the eSDHCs are becoming more and
> more different. We should have split it into two drivers, like them
> (sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.
>
> This patch is just to create a fsl_esdhc_imx driver which is a copy
> of fsl_esdhc driver for i.MX processors. We will convert i.MX
> processors to use fsl_esdhc_imx, and clean up the two drivers
> separately in the future patches.
>
> Signed-off-by: Yangbo Lu <yangbo.lu at nxp.com>
> ---
> Changes for v2:
> - None.
> Changes for v3:
> - None.
> ---
> drivers/mmc/Kconfig | 6 ++++++
> drivers/mmc/Makefile | 1 +
> drivers/mmc/{fsl_esdhc.c => fsl_esdhc_imx.c} | 5 +++--
> include/{fsl_esdhc.h => fsl_esdhc_imx.h} | 11 ++++++-----
> 4 files changed, 16 insertions(+), 7 deletions(-)
> copy drivers/mmc/{fsl_esdhc.c => fsl_esdhc_imx.c} (99%)
> copy include/{fsl_esdhc.h => fsl_esdhc_imx.h} (97%)
>
> diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
> index c23299ea96..4e33fa1b2d 100644
> --- a/drivers/mmc/Kconfig
> +++ b/drivers/mmc/Kconfig
> @@ -671,6 +671,12 @@ config FSL_ESDHC
> This selects support for the eSDHC (enhanced secure
> digital host controller) found on numerous Freescale/NXP SoCs.
>
> +config FSL_ESDHC_IMX
> + bool "Freescale/NXP i.MX eSDHC controller support"
> + help
> + This selects support for the i.MX eSDHC (enhanced secure
> digital host
> + controller) found on numerous Freescale/NXP SoCs.
> +
You shall use capital letters for "Enhanced Secure Digital Host"
> endmenu
>
> config SYS_FSL_ERRATUM_ESDHC111
> diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
> index 0076fc393b..3c8c53a9e1 100644
> --- a/drivers/mmc/Makefile
> +++ b/drivers/mmc/Makefile
> @@ -26,6 +26,7 @@ obj-$(CONFIG_MMC_DW_ROCKCHIP) +=
> rockchip_dw_mmc.o obj-$(CONFIG_MMC_DW_SOCFPGA) +=
> socfpga_dw_mmc.o obj-$(CONFIG_MMC_DW_SNPS) +=
> snps_dw_mmc.o obj-$(CONFIG_FSL_ESDHC) += fsl_esdhc.o
> +obj-$(CONFIG_FSL_ESDHC_IMX) += fsl_esdhc_imx.o
> obj-$(CONFIG_FTSDC010) += ftsdc010_mci.o
> obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o
> obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o
> diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc_imx.c
> similarity index 99%
> copy from drivers/mmc/fsl_esdhc.c
> copy to drivers/mmc/fsl_esdhc_imx.c
> index 1b7de74a72..faf133390f 100644
> --- a/drivers/mmc/fsl_esdhc.c
> +++ b/drivers/mmc/fsl_esdhc_imx.c
> @@ -2,6 +2,7 @@
> /*
> * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc
> * Andy Fleming
> + * Copyright 2019 NXP
This line shall be on top of the comment. Also you shall state your
name and e-mail.
> *
> * Based vaguely on the pxa mmc code:
> * (C) Copyright 2003
> @@ -18,7 +19,7 @@
> #include <part.h>
> #include <power/regulator.h>
> #include <malloc.h>
> -#include <fsl_esdhc.h>
> +#include <fsl_esdhc_imx.h>
> #include <fdt_support.h>
> #include <asm/io.h>
> #include <dm.h>
> @@ -110,7 +111,7 @@ struct esdhc_soc_data {
> * @non_removable: 0: removable; 1: non-removable
> * @wp_enable: 1: enable checking wp; 0: no check
> * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V
> - * @flags: ESDHC_FLAG_xx in include/fsl_esdhc.h
> + * @flags: ESDHC_FLAG_xx in include/fsl_esdhc_imx.h
> * @caps: controller capabilities
> * @tuning_step: tuning step setting in tuning_ctrl register
> * @start_tuning_tap: the start point for tuning in tuning_ctrl
> register diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc_imx.h
> similarity index 97%
> copy from include/fsl_esdhc.h
> copy to include/fsl_esdhc_imx.h
> index 8dbd5249a7..e05b24e7e8 100644
> --- a/include/fsl_esdhc.h
> +++ b/include/fsl_esdhc_imx.h
> @@ -4,10 +4,11 @@
> *-------------------------------------------------------------------
> *
> * Copyright 2007-2008,2010-2011 Freescale Semiconductor, Inc
> + * Copyright 2019 NXP
The same comment as above applies.
> */
>
> -#ifndef __FSL_ESDHC_H__
> -#define __FSL_ESDHC_H__
> +#ifndef __FSL_ESDHC_IMX_H__
> +#define __FSL_ESDHC_IMX_H__
>
> #include <linux/bitops.h>
> #include <linux/errno.h>
> @@ -258,15 +259,15 @@ struct fsl_esdhc_cfg {
> #error "Endianess is not defined: please fix to continue"
> #endif
>
> -#ifdef CONFIG_FSL_ESDHC
> +#ifdef CONFIG_FSL_ESDHC_IMX
> int fsl_esdhc_mmc_init(bd_t *bis);
> int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg);
> void fdt_fixup_esdhc(void *blob, bd_t *bd);
> #else
> static inline int fsl_esdhc_mmc_init(bd_t *bis) { return -ENOSYS; }
> static inline void fdt_fixup_esdhc(void *blob, bd_t *bd) {}
> -#endif /* CONFIG_FSL_ESDHC */
> +#endif /* CONFIG_FSL_ESDHC_IMX */
> void __noreturn mmc_boot(void);
> void mmc_spl_load_image(uint32_t offs, unsigned int size, void
> *vdst);
> -#endif /* __FSL_ESDHC_H__ */
> +#endif /* __FSL_ESDHC_IMX_H__ */
Please also use buildman to check if your changes (separate commits)
can be build (so in the future one can still use bisect).
You may want to use "buildman" tool - e.g.:
./tools/buildman/buildman.py --branch=HEAD mx5 mx6 mx7 --show_errors
--force-build --count=5 --output-dir=../BUILD
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20190529/106c4a0a/attachment.sig>
More information about the U-Boot
mailing list