[U-Boot] [v3, 5/5] mmc: fsl_esdhc_imx: drop useless code
Peng Fan
peng.fan at nxp.com
Fri May 31 05:58:52 UTC 2019
Hi,
> Subject: Re: [v3, 5/5] mmc: fsl_esdhc_imx: drop useless code
>
> Hi Lu,
>
> On Tue, May 21, 2019 at 08:53:04AM +0000, Y.b. Lu wrote:
> > Dropped useless code for i.MX eSDHC driver.
> >
> > Signed-off-by: Yangbo Lu <yangbo.lu at nxp.com>
> > ---
> > Changes for v2:
> > - Added this patch.
> > Changes for v3:
> > - None.
> > ---
> > drivers/mmc/fsl_esdhc_imx.c | 96 ++-----------------------------------
> > include/fsl_esdhc_imx.h | 4 --
> > 2 files changed, 4 insertions(+), 96 deletions(-)
> >
> > diff --git a/drivers/mmc/fsl_esdhc_imx.c b/drivers/mmc/fsl_esdhc_imx.c
> > index faf133390f..1c02e0eef1 100644
> > --- a/drivers/mmc/fsl_esdhc_imx.c
> > +++ b/drivers/mmc/fsl_esdhc_imx.c
> > @@ -259,8 +259,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv
> > *priv, struct mmc *mmc, {
> > int timeout;
> > struct fsl_esdhc *regs = priv->esdhc_regs; -#if
> > defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> > - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> > +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> > +defined(CONFIG_IMX8M)
> > dma_addr_t addr;
> > #endif
> > uint wml_value;
> > @@ -273,8 +272,7 @@ static int esdhc_setup_data(struct fsl_esdhc_priv
> > *priv, struct mmc *mmc,
> >
> > esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK,
> wml_value);
> > #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO -#if
> > defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> > - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> > +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> > +defined(CONFIG_IMX8M)
> > addr = virt_to_phys((void *)(data->dest));
> > if (upper_32_bits(addr))
> > printf("Error found for upper 32 bits\n"); @@ -310,8 +308,7
> @@
> > static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc,
> > esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK,
> > wml_value << 16);
> > #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO
> > -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> > - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> > +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> > +defined(CONFIG_IMX8M)
> > addr = virt_to_phys((void *)(data->src));
> > if (upper_32_bits(addr))
> > printf("Error found for upper 32 bits\n"); @@ -376,8 +373,7
> @@
> > static void check_and_invalidate_dcache_range
> > unsigned end = 0;
> > unsigned size = roundup(ARCH_DMA_MINALIGN,
> > data->blocks*data->blocksize);
> > -#if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \
> > - defined(CONFIG_IMX8) || defined(CONFIG_IMX8M)
> > +#if defined(CONFIG_S32V234) || defined(CONFIG_IMX8) ||
> > +defined(CONFIG_IMX8M)
> > dma_addr_t addr;
> >
> > addr = virt_to_phys((void *)(data->dest)); @@ -392,25 +388,6 @@
> > static void check_and_invalidate_dcache_range
> > invalidate_dcache_range(start, end); }
> >
> > -#ifdef CONFIG_MCF5441x
> > -/*
> > - * Swaps 32-bit words to little-endian byte order.
> > - */
> > -static inline void sd_swap_dma_buff(struct mmc_data *data) -{
> > - int i, size = data->blocksize >> 2;
> > - u32 *buffer = (u32 *)data->dest;
> > - u32 sw;
> > -
> > - while (data->blocks--) {
> > - for (i = 0; i < size; i++) {
> > - sw = __sw32(*buffer);
> > - *buffer++ = sw;
> > - }
> > - }
> > -}
> > -#endif
> > -
>
> Doing so you remove the ColdFire family code (mcf5441x) i just added recently.
> Since they are big-endian, and dma hw has no options to swap, swap is
> needed.
>
> Please don't remove it.
The mcf code is still in fsl_esdhc.c, this patch is to modify fsl_esdhc_imx.c.
Regards,
Peng.
>
> > /*
> > * Sends a command out on the bus. Takes the mmc pointer,
> > * a command pointer, and an optional data pointer.
> > @@ -575,9 +552,6 @@ static int esdhc_send_cmd_common(struct
> fsl_esdhc_priv *priv, struct mmc *mmc,
> > */
> > if (data->flags & MMC_DATA_READ) {
> > check_and_invalidate_dcache_range(cmd, data); -#ifdef
> > CONFIG_MCF5441x
> > - sd_swap_dma_buff(data);
>
> Same here.
>
> > -#endif
> > }
> > #endif
> > }
> > @@ -1073,12 +1047,8 @@ static int esdhc_init_common(struct
> fsl_esdhc_priv *priv, struct mmc *mmc)
> > /* Disable the BRR and BWR bits in IRQSTAT */
> > esdhc_clrbits32(®s->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR);
> >
> > -#ifdef CONFIG_MCF5441x
> > - esdhc_write32(®s->proctl, PROCTL_INIT | PROCTL_D3CD);
> > -#else
> > /* Put the PROCTL reg back to the default */
> > esdhc_write32(®s->proctl, PROCTL_INIT); -#endif
> >
> > /* Set timout to the maximum value */
> > esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16);
> @@
> > -1186,11 +1156,6 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv *priv,
> > if (ret)
> > return ret;
> >
> > -#ifdef CONFIG_MCF5441x
> > - /* ColdFire, using SDHC_DATA[3] for card detection */
> > - esdhc_write32(®s->proctl, PROCTL_INIT | PROCTL_D3CD);
> > -#endif
> > -
> > #ifndef CONFIG_FSL_USDHC
> > esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN
> > | SYSCTL_IPGEN | SYSCTL_CKEN);
> > @@ -1215,15 +1180,6 @@ static int fsl_esdhc_init(struct fsl_esdhc_priv
> *priv,
> > voltage_caps = 0;
> > caps = esdhc_read32(®s->hostcapblt);
> >
> > -#ifdef CONFIG_MCF5441x
> > - /*
> > - * MCF5441x RM declares in more points that sdhc clock speed must
> > - * never exceed 25 Mhz. From this, the HS bit needs to be disabled
> > - * from host capabilities.
> > - */
> > - caps &= ~ESDHC_HOSTCAPBLT_HSS;
> > -#endif
>
> Same here.
>
>
> > -
> > #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135
> > caps = caps & ~(ESDHC_HOSTCAPBLT_SRS |
> > ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30); @@
> -1375,45
> > +1331,6 @@ int fsl_esdhc_mmc_init(bd_t *bis) } #endif
> >
> > -#ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT -void
> > mmc_adapter_card_type_ident(void) -{
> > - u8 card_id;
> > - u8 value;
> > -
> > - card_id = QIXIS_READ(present) & QIXIS_SDID_MASK;
> > - gd->arch.sdhc_adapter = card_id;
> > -
> > - switch (card_id) {
> > - case QIXIS_ESDHC_ADAPTER_TYPE_EMMC45:
> > - value = QIXIS_READ(brdcfg[5]);
> > - value |= (QIXIS_DAT4 | QIXIS_DAT5_6_7);
> > - QIXIS_WRITE(brdcfg[5], value);
> > - break;
> > - case QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY:
> > - value = QIXIS_READ(pwr_ctl[1]);
> > - value |= QIXIS_EVDD_BY_SDHC_VS;
> > - QIXIS_WRITE(pwr_ctl[1], value);
> > - break;
> > - case QIXIS_ESDHC_ADAPTER_TYPE_EMMC44:
> > - value = QIXIS_READ(brdcfg[5]);
> > - value |= (QIXIS_SDCLKIN | QIXIS_SDCLKOUT);
> > - QIXIS_WRITE(brdcfg[5], value);
> > - break;
> > - case QIXIS_ESDHC_ADAPTER_TYPE_RSV:
> > - break;
> > - case QIXIS_ESDHC_ADAPTER_TYPE_MMC:
> > - break;
> > - case QIXIS_ESDHC_ADAPTER_TYPE_SD:
> > - break;
> > - case QIXIS_ESDHC_NO_ADAPTER:
> > - break;
> > - default:
> > - break;
> > - }
> > -}
> > -#endif
> > -
> > #ifdef CONFIG_OF_LIBFDT
> > __weak int esdhc_status_fixup(void *blob, const char *compat) { @@
> > -1441,10 +1358,6 @@ void fdt_fixup_esdhc(void *blob, bd_t *bd)
> > do_fixup_by_compat_u32(blob, compat, "clock-frequency",
> > gd->arch.sdhc_clk, 1);
> > #endif
> > -#ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT
> > - do_fixup_by_compat_u32(blob, compat, "adapter-type",
> > - (u32)(gd->arch.sdhc_adapter), 1);
> > -#endif
> > }
> > #endif
> >
> > @@ -1654,7 +1567,6 @@ static const struct udevice_id fsl_esdhc_ids[] = {
> > { .compatible = "fsl,imx6q-usdhc", },
> > { .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,},
> > { .compatible = "fsl,imx7ulp-usdhc", },
> > - { .compatible = "fsl,esdhc", },
> > { /* sentinel */ }
> > };
> >
> > diff --git a/include/fsl_esdhc_imx.h b/include/fsl_esdhc_imx.h index
> > e05b24e7e8..8abd28ea50 100644
> > --- a/include/fsl_esdhc_imx.h
> > +++ b/include/fsl_esdhc_imx.h
> > @@ -17,10 +17,6 @@
> > /* needed for the mmc_cfg definition */ #include <mmc.h>
> >
> > -#ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT -#include
> > "../board/freescale/common/qixis.h"
> > -#endif
> > -
> > /* FSL eSDHC-specific constants */
> > #define SYSCTL 0x0002e02c
> > #define SYSCTL_INITA 0x08000000
> > --
> > 2.17.1
> >
More information about the U-Boot
mailing list