[U-Boot] [PATCH 1/2] drivers: net: add NXP ENETC ethernet driver
Alex Marginean
alexm.osslist at gmail.com
Fri May 31 16:33:07 UTC 2019
Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028a. ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.
Signed-off-by: Catalin Horghidan <catalin.horghidan at nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist at gmail.com>
---
configs/ls1028aqds_tfa_defconfig | 1 +
configs/ls1028ardb_tfa_defconfig | 1 +
drivers/net/Kconfig | 7 +
drivers/net/Makefile | 1 +
drivers/net/fsl_enetc.c | 345 +++++++++++++++++++++++++++++++
drivers/net/fsl_enetc.h | 176 ++++++++++++++++
include/pci_ids.h | 1 +
7 files changed, 532 insertions(+)
create mode 100644 drivers/net/fsl_enetc.c
create mode 100644 drivers/net/fsl_enetc.h
diff --git a/configs/ls1028aqds_tfa_defconfig b/configs/ls1028aqds_tfa_defconfig
index 7982ce4157..11fe344b04 100644
--- a/configs/ls1028aqds_tfa_defconfig
+++ b/configs/ls1028aqds_tfa_defconfig
@@ -45,6 +45,7 @@ CONFIG_PHY_ATHEROS=y
CONFIG_DM_ETH=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_FSL_ENETC=y
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
diff --git a/configs/ls1028ardb_tfa_defconfig b/configs/ls1028ardb_tfa_defconfig
index c65e37df79..ab6f2a850c 100644
--- a/configs/ls1028ardb_tfa_defconfig
+++ b/configs/ls1028ardb_tfa_defconfig
@@ -45,6 +45,7 @@ CONFIG_PHY_ATHEROS=y
CONFIG_DM_ETH=y
CONFIG_PHY_GIGE=y
CONFIG_E1000=y
+CONFIG_FSL_ENETC=y
CONFIG_PCI=y
CONFIG_DM_PCI=y
CONFIG_DM_PCI_COMPAT=y
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 6fba5a84dd..4aa82261f8 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -556,4 +556,11 @@ config HIGMACV300_ETH
This driver supports HIGMACV300 Ethernet controller found on
HiSilicon SoCs.
+config FSL_ENETC
+ bool "NXP ENETC Ethernet controller"
+ depends on DM_PCI && DM_ETH
+ help
+ This driver supports the NXP ENETC Ethernet controller found on some
+ of the NXP SoCs.
+
endif # NETDEVICES
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 8d02a37896..67b88ebae8 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -77,3 +77,4 @@ obj-y += ti/
obj-$(CONFIG_MEDIATEK_ETH) += mtk_eth.o
obj-y += mscc_eswitch/
obj-$(CONFIG_HIGMACV300_ETH) += higmacv300.o
+obj-$(CONFIG_FSL_ENETC) += fsl_enetc.o
diff --git a/drivers/net/fsl_enetc.c b/drivers/net/fsl_enetc.c
new file mode 100644
index 0000000000..b253292bc0
--- /dev/null
+++ b/drivers/net/fsl_enetc.c
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * ENETC ethernet controller driver
+ * Copyright 2017-2019 NXP
+ */
+
+#include "fsl_enetc.h"
+
+#include <dm.h>
+#include <errno.h>
+#include <memalign.h>
+#include <asm/io.h>
+#include <pci.h>
+
+static int enetc_bind(struct udevice *dev)
+{
+ static int eth_num_devices;
+ char name[16];
+
+ /* prefer using PCI function numbers, if not available use #idx */
+ if (ofnode_valid(dev->node))
+ sprintf(name, "enetc%u", PCI_FUNC(pci_get_devfn(dev)));
+ else
+ sprintf(name, "enetc#%u", eth_num_devices++);
+
+ device_set_name(dev, name);
+
+ return 0;
+}
+
+/*
+ * Probe ENETC driver:
+ * - initialize port and station interface BARs
+ */
+static int enetc_probe(struct udevice *dev)
+{
+ struct enetc_devfn *hw = dev_get_priv(dev);
+ int err = 0;
+
+ if (ofnode_valid(dev->node) && !ofnode_is_available(dev->node)) {
+ ENETC_DBG(dev, "interface disabled\n");
+ return -ENODEV;
+ }
+
+ /* initialize register */
+ hw->regs_base = dm_pci_map_bar(dev, PCI_BASE_ADDRESS_0, 0);
+ if (!hw->regs_base) {
+ ENETC_DBG(dev, "failed to map BAR0\n");
+ return -EINVAL;
+ }
+ hw->port_regs = hw->regs_base + 0x10000;
+
+ dm_pci_clrset_config16(dev, PCI_COMMAND, 0, PCI_COMMAND_MEMORY);
+
+ return err;
+}
+
+/* ENETC Port MAC address registers accept big-endian format */
+static void enetc_set_primary_mac_addr(struct enetc_devfn *hw, const u8 *addr)
+{
+ u16 lower = *(const u16 *)(addr + 4);
+ u32 upper = *(const u32 *)addr;
+
+ enetc_write_port(hw, ENETC_PSIPMAR0, upper);
+ enetc_write_port(hw, ENETC_PSIPMAR1, lower);
+}
+
+int enetc_enable_si_port(struct enetc_devfn *hw)
+{
+ u32 val;
+
+ /* set Rx/Tx BDR count */
+ val = ENETC_PSICFGR_SET_TXBDR(ENETC_TX_BDR_CNT);
+ val |= ENETC_PSICFGR_SET_RXBDR(ENETC_RX_BDR_CNT);
+ enetc_write_port(hw, ENETC_PSICFGR(0), val);
+ /* set Rx max frame size */
+ enetc_write_port(hw, ENETC_PM_MAXFRM, ENETC_RX_MAXFRM_SIZE);
+ /* enable MAC port */
+ enetc_write_port(hw, ENETC_PM_CC, ENETC_PM_CC_RX_TX_EN);
+ /* enable port */
+ enetc_write_port(hw, ENETC_PMR, ENETC_PMR_SI0_EN);
+ /* set SI cache policy */
+ enetc_write(hw, ENETC_SICAR0, ENETC_SICAR_RD_CFG | ENETC_SICAR_WR_CFG);
+ /* enable SI */
+ enetc_write(hw, ENETC_SIMR, ENETC_SIMR_EN);
+
+ return 0;
+}
+
+/* Use a single set of BDs and buffers. It's functionally OK as u-boot doesn't
+ * use multiple interfaces at once.
+ */
+DEFINE_ALIGN_BUFFER(struct enetc_tx_bd, enetc_txbd, ENETC_BD_CNT, ENETC_ALIGN);
+DEFINE_ALIGN_BUFFER(union enetc_rx_bd, enetc_rxbd, ENETC_BD_CNT, ENETC_ALIGN);
+DEFINE_ALIGN_BUFFER(u8, enetc_rx_buff, ENETC_RX_MBUFF_SIZE, ENETC_ALIGN);
+
+static inline u64 enetc_rxb_address(struct udevice *dev, int i)
+{
+ int off = i * ENETC_RX_MAXFRM_SIZE;
+
+ return cpu_to_le64(dm_pci_virt_to_mem(dev, enetc_rx_buff + off));
+}
+
+/**
+ * Setup a single Tx BD Ring (ID = 0):
+ * - set Tx buffer descriptor address
+ * - set the BD count
+ * - initialize the producer and consumer index
+ */
+static void enetc_setup_tx_bdr(struct enetc_devfn *hw)
+{
+ struct bd_ring *tx_bdr = &hw->tx_bdr;
+ u64 tx_bd_add = (u64)enetc_txbd;
+
+ /* used later to advance to the next Tx BD */
+ tx_bdr->bd_count = ENETC_BD_CNT;
+ tx_bdr->next_prod_idx = 0;
+ tx_bdr->next_cons_idx = 0;
+ tx_bdr->cons_idx = hw->regs_base +
+ ENETC_BDR(TX, ENETC_TX_BDR_ID, ENETC_TBCIR);
+ tx_bdr->prod_idx = hw->regs_base +
+ ENETC_BDR(TX, ENETC_TX_BDR_ID, ENETC_TBPIR);
+
+ /* set Tx BD address */
+ enetc_bdr_write(hw, TX, ENETC_TX_BDR_ID, ENETC_TBBAR0,
+ lower_32_bits(tx_bd_add));
+ enetc_bdr_write(hw, TX, ENETC_TX_BDR_ID, ENETC_TBBAR1,
+ upper_32_bits(tx_bd_add));
+ /* set Tx 8 BD count */
+ enetc_bdr_write(hw, TX, ENETC_TX_BDR_ID, ENETC_TBLENR,
+ tx_bdr->bd_count);
+
+ /* reset both producer/consumer indexes */
+ enetc_write_reg(tx_bdr->cons_idx, tx_bdr->next_cons_idx);
+ enetc_write_reg(tx_bdr->prod_idx, tx_bdr->next_prod_idx);
+
+ /* enable TX ring */
+ enetc_bdr_write(hw, TX, ENETC_TX_BDR_ID, ENETC_TBMR, ENETC_TBMR_EN);
+}
+
+/**
+ * Setup a single Rx BD Ring (ID = 0):
+ * - set Rx buffer descriptors address (one descriptor per buffer)
+ * - set buffer size as max frame size
+ * - enable Rx ring
+ * - reset consumer and producer indexes
+ * - set buffer for each descriptor
+ */
+static void enetc_setup_rx_bdr(struct udevice *dev, struct enetc_devfn *hw)
+{
+ struct bd_ring *rx_bdr = &hw->rx_bdr;
+ u64 rx_bd_add = (u64)enetc_rxbd;
+ int i;
+
+ /* used later to advance to the next BD produced by ENETC HW */
+ rx_bdr->bd_count = ENETC_BD_CNT;
+ rx_bdr->next_prod_idx = 0;
+ rx_bdr->next_cons_idx = ENETC_RBCI_INIT;
+ rx_bdr->cons_idx = hw->regs_base +
+ ENETC_BDR(RX, ENETC_RX_BDR_ID, ENETC_RBCIR);
+ rx_bdr->prod_idx = hw->regs_base +
+ ENETC_BDR(RX, ENETC_RX_BDR_ID, ENETC_RBPIR);
+
+ /* set Rx BD address */
+ enetc_bdr_write(hw, RX, ENETC_RX_BDR_ID, ENETC_RBBAR0,
+ lower_32_bits(rx_bd_add));
+ enetc_bdr_write(hw, RX, ENETC_RX_BDR_ID, ENETC_RBBAR1,
+ upper_32_bits(rx_bd_add));
+ /* set Rx BD count (multiple of 8) */
+ enetc_bdr_write(hw, RX, ENETC_RX_BDR_ID, ENETC_RBLENR,
+ rx_bdr->bd_count);
+ /* set Rx buffer size */
+ enetc_bdr_write(hw, RX, ENETC_RX_BDR_ID, ENETC_RBBSR, ENETC_BUFF_SIZE);
+
+ /* reset producer (ENETC owned) and consumer (SW owned) index */
+ enetc_write_reg(rx_bdr->cons_idx, rx_bdr->next_cons_idx);
+ enetc_write_reg(rx_bdr->prod_idx, rx_bdr->next_prod_idx);
+
+ /* fill Rx BD */
+ memset(enetc_rxbd, 0, rx_bdr->bd_count * sizeof(union enetc_rx_bd));
+ for (i = 0; i < rx_bdr->bd_count; i++) {
+ enetc_rxbd[i].w.addr = enetc_rxb_address(dev, i);
+ /* each RX buffer must be aligned to 64B */
+ WARN_ON(enetc_rxbd[i].w.addr & (ENETC_ALIGN - 1));
+ }
+ /* enable Rx ring */
+ enetc_bdr_write(hw, RX, ENETC_RX_BDR_ID, ENETC_RBMR, ENETC_RBMR_EN);
+}
+
+/**
+ * Start ENETC interface:
+ * - perform FLR
+ * - enable access to port and SI registers
+ * - set mac address
+ * - setup TX/RX buffer descriptors
+ * - enable Tx/Rx rings
+ */
+static int enetc_start(struct udevice *dev)
+{
+ struct eth_pdata *plat = dev_get_platdata(dev);
+ struct enetc_devfn *hw = dev_get_priv(dev);
+ u32 if_mode;
+
+ /* reset and enable the PCI device */
+ dm_pci_flr(dev);
+ dm_pci_clrset_config16(dev, PCI_COMMAND, 0,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ if_mode = enetc_read_port(hw, ENETC_PM_IF_MODE);
+ if (if_mode & ENETC_PM_IF_MODE_RG)
+ if_mode |= ENETC_PM_IF_MODE_AN_ENA;
+ enetc_write_port(hw, ENETC_PM_IF_MODE, if_mode);
+
+ if (!is_valid_ethaddr(plat->enetaddr)) {
+ ENETC_DBG(dev, "invalid MAC address, generate random ...\n");
+ net_random_ethaddr(plat->enetaddr);
+ }
+ enetc_set_primary_mac_addr(hw, plat->enetaddr);
+
+ enetc_enable_si_port(hw);
+
+ /* setup Tx/Rx buffer descriptors */
+ enetc_setup_tx_bdr(hw);
+ enetc_setup_rx_bdr(dev, hw);
+
+ return 0;
+}
+
+/* FLR is sufficient to quiesce the device */
+static void enetc_stop(struct udevice *dev)
+{
+ /* reset device */
+ dm_pci_flr(dev);
+}
+
+/**
+ * ENETC transmit packet:
+ * - check if Tx BD ring is full
+ * - set buffer/packet address (dma address)
+ * - set final fragment flag
+ * - try while producer index equals consumer index or timeout
+ */
+static int enetc_send(struct udevice *dev, void *packet, int length)
+{
+ struct enetc_devfn *hw = dev_get_priv(dev);
+ struct bd_ring *txr = &hw->tx_bdr;
+ void *nv_packet = (void *)packet;
+ int tries = ENETC_POLL_TRIES;
+ u32 pi, ci;
+
+ pi = txr->next_prod_idx;
+ ci = enetc_read_reg(txr->cons_idx) & ENETC_BDR_IDX_MASK;
+ /* Tx ring is full when */
+ if (((pi + 1) % txr->bd_count) == ci) {
+ ENETC_DBG(dev, "Tx BDR full\n");
+ return -ETIMEDOUT;
+ }
+ ENETC_DBG(dev, "TxBD[%d]send: pkt_len=%d, buff @0x%x%08x\n", pi, length,
+ upper_32_bits((u64)nv_packet), lower_32_bits((u64)nv_packet));
+
+ /* prepare Tx BD */
+ memset(&enetc_txbd[pi], 0x0, sizeof(struct enetc_tx_bd));
+ enetc_txbd[pi].addr = cpu_to_le64(dm_pci_virt_to_mem(dev, nv_packet));
+ enetc_txbd[pi].buf_len = cpu_to_le16(length);
+ enetc_txbd[pi].frm_len = cpu_to_le16(length);
+ enetc_txbd[pi].flags = cpu_to_le16(ENETC_TXBD_FLAGS_F);
+ dmb();
+ /* send frame: increment producer index */
+ pi = (pi + 1) % txr->bd_count;
+ txr->next_prod_idx = pi;
+ enetc_write_reg(txr->prod_idx, pi);
+ while ((--tries >= 0) &&
+ (pi != (enetc_read_reg(txr->cons_idx) & ENETC_BDR_IDX_MASK)))
+ udelay(10);
+
+ return tries > 0 ? 0 : -ETIMEDOUT;
+}
+
+/**
+ * Handles frame receive and cleans up the BD slot on the Rx ring.
+ */
+static int enetc_recv(struct udevice *dev, int flags, uchar **packetp)
+{
+ struct enetc_devfn *hw = dev_get_priv(dev);
+ struct bd_ring *rxr = &hw->rx_bdr;
+ int tries = ENETC_POLL_TRIES;
+ int pi = rxr->next_prod_idx;
+ int ci = rxr->next_cons_idx;
+ u32 status;
+ int len;
+ u8 rdy;
+
+ do {
+ dmb();
+ status = le32_to_cpu(enetc_rxbd[pi].r.lstatus);
+ /* check if current BD is ready to be consumed */
+ rdy = ENETC_RXBD_STATUS_R(status);
+ } while (--tries >= 0 && !rdy);
+
+ if (!rdy)
+ return -EAGAIN;
+
+ dmb();
+ len = le16_to_cpu(enetc_rxbd[pi].r.buf_len);
+ *packetp = (uchar *)enetc_rxb_address(dev, pi);
+ ENETC_DBG(dev, "RxBD[%d]: len=%d err=%d pkt=0x%x%08x\n", pi, len,
+ ENETC_RXBD_STATUS_ERRORS(status),
+ upper_32_bits((u64)*packetp), lower_32_bits((u64)*packetp));
+
+ /* BD clean up and advance to next in ring */
+ memset(&enetc_rxbd[pi], 0, sizeof(union enetc_rx_bd));
+ enetc_rxbd[pi].w.addr = enetc_rxb_address(dev, pi);
+ rxr->next_prod_idx = (pi + 1) % rxr->bd_count;
+ ci = (ci + 1) % rxr->bd_count;
+ rxr->next_cons_idx = ci;
+ dmb();
+ /* free up the slot in the ring for HW */
+ enetc_write_reg(rxr->cons_idx, ci);
+
+ return len;
+}
+
+static const struct eth_ops enetc_ops = {
+ .start = enetc_start,
+ .send = enetc_send,
+ .recv = enetc_recv,
+ .stop = enetc_stop,
+};
+
+U_BOOT_DRIVER(eth_enetc) = {
+ .name = "enetc_eth",
+ .id = UCLASS_ETH,
+ .bind = enetc_bind,
+ .probe = enetc_probe,
+ .ops = &enetc_ops,
+ .priv_auto_alloc_size = sizeof(struct enetc_devfn),
+ .platdata_auto_alloc_size = sizeof(struct eth_pdata),
+};
+
+static struct pci_device_id enetc_ids[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_FREESCALE, PCI_DEVICE_ID_ENETC_PF_V1) },
+ {}
+};
+
+U_BOOT_PCI_DEVICE(eth_enetc, enetc_ids);
diff --git a/drivers/net/fsl_enetc.h b/drivers/net/fsl_enetc.h
new file mode 100644
index 0000000000..4ebf03a61a
--- /dev/null
+++ b/drivers/net/fsl_enetc.h
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * ENETC ethernet controller driver
+ * Copyright 2017-2019 NXP
+ */
+
+#ifndef _ENETC_H
+#define _ENETC_H
+
+#include <common.h>
+
+#ifdef ENETC_DEBUG
+#define ENETC_DBG(udev, fmt, args...) \
+ printf("enetc[%s]: " fmt, udev->name, ##args)
+#else
+#define ENETC_DBG(devno, args...) do { } while (0)
+#endif
+/* ENETC controller registers */
+
+/* Station interface register offsets */
+#define ENETC_SIMR 0
+#define ENETC_SIMR_EN BIT(31)
+#define ENETC_SICAR0 0x40
+/* write cache cfg: snoop, no allocate, update full (data), partial (BD) */
+#define ENETC_SICAR_WR_CFG 0x6767
+/* read cache cfg: coherent copy, look up, no allocate */
+#define ENETC_SICAR_RD_CFG 0x27270000
+
+#define ENETC_SIROCT 0x300
+#define ENETC_SIRFRM 0x308
+#define ENETC_SITOCT 0x320
+#define ENETC_SITFRM 0x328
+
+/* Station Interface Rx/Tx Buffer Descriptor Ring registers */
+enum enetc_bdr_type {TX, RX};
+#define ENETC_BDR(type, n, off) (0x8000 + (type) * 0x100 + (n) * 0x200 + (off))
+#define ENETC_BDR_IDX_MASK 0xffff
+
+/* Rx BDR reg offsets */
+#define ENETC_RBMR 0
+#define ENETC_RBMR_EN BIT(31)
+#define ENETC_RBBSR 0x8
+#define ENETC_RBCIR 0xc
+/* initial consumer index for Rx BDR */
+#define ENETC_RBCI_INIT 4
+#define ENETC_RBBAR0 0x10
+#define ENETC_RBBAR1 0x14
+#define ENETC_RBPIR 0x18
+#define ENETC_RBLENR 0x20
+
+/* Tx BDR reg offsets */
+#define ENETC_TBMR 0
+#define ENETC_TBMR_EN BIT(31)
+#define ENETC_TBBAR0 0x10
+#define ENETC_TBBAR1 0x14
+#define ENETC_TBPIR 0x18
+#define ENETC_TBCIR 0x1c
+#define ENETC_TBLENR 0x20
+
+/* Port registers offset */
+#define ENETC_PORT_REGS_OFF 0x10000
+#define ENETC_PMR 0x00000
+
+#define ENETC_PMR_SI0_EN BIT(16)
+#define ENETC_PSIPMMR 0x18
+#define ENETC_PSIPMAR0 0x00100
+#define ENETC_PSIPMAR1 0x00104
+#define ENETC_PSICFGR(n) (0x00940 + (n) * 0x10)
+#define ENETC_PSICFGR_SET_TXBDR(val) ((val) & 0xff)
+#define ENETC_PSICFGR_SET_RXBDR(val) (((val) & 0xff) << 16)
+#define ENETC_EMDIO_CFG 0x1c00
+#define ENETC_PM_CC 0x8008
+/* Port config: enable MAC Tx/Rx, Tx padding, MAC promisc */
+#define ENETC_PM_CC_DEFAULT 0x810
+#define ENETC_PM_CC_RX_TX_EN 0x8813
+#define ENETC_PM_MAXFRM 0x8014
+#define ENETC_RX_MAXFRM_SIZE PKTSIZE_ALIGN
+#define ENETC_BUFF_SIZE PKTSIZE_ALIGN
+#define ENETC_PM_IF_MODE 0x8300
+#define ENETC_PM_IF_MODE_RG 0x00000004
+#define ENETC_PM_IF_MODE_AN_ENA 0x00008000
+#define ENETC_PM_IF_STATUS 0x8304
+#define ENETC_PM_IF_STATUS_RGL 0x00008000
+#define ENETC_PM_IF_STATUS_RGFD 0x00001000
+/* buffer descriptors count must be multiple of 8 and aligned to 128 bytes */
+#define ENETC_BD_CNT 16
+#define ENETC_ALIGN 128
+#define ENETC_RX_MBUFF_SIZE (ENETC_BD_CNT * ENETC_RX_MAXFRM_SIZE)
+
+/* single pair of Rx/Tx rings */
+#define ENETC_RX_BDR_CNT 1
+#define ENETC_TX_BDR_CNT 1
+#define ENETC_RX_BDR_ID 0
+#define ENETC_TX_BDR_ID 0
+
+/* Tx buffer descriptor */
+struct enetc_tx_bd {
+ __le64 addr;
+ __le16 buf_len;
+ __le16 frm_len;
+ __le16 err_csum;
+ __le16 flags;
+};
+
+#define ENETC_TXBD_FLAGS_F BIT(15)
+#define ENETC_POLL_TRIES 0x8000
+
+/* Rx buffer descriptor */
+union enetc_rx_bd {
+ /* SW provided BD format */
+ struct {
+ __le64 addr;
+ u8 reserved[8];
+ } w;
+
+ /* ENETC returned BD format */
+ struct {
+ __le16 inet_csum;
+ __le16 parse_summary;
+ __le32 rss_hash;
+ __le16 buf_len;
+ __le16 vlan_opt;
+ union {
+ struct {
+ __le16 flags;
+ __le16 error;
+ };
+ __le32 lstatus;
+ };
+ } r;
+};
+
+#define ENETC_RXBD_STATUS_R(status) (((status) >> 30) & 0x1)
+#define ENETC_RXBD_STATUS_F(status) (((status) >> 31) & 0x1)
+#define ENETC_RXBD_STATUS_ERRORS(status) (((status) >> 16) & 0xff)
+#define ENETC_RXBD_STATUS(flags) ((flags) << 16)
+
+/* Tx/Rx ring info */
+struct bd_ring {
+ void *cons_idx;
+ void *prod_idx;
+ /* next BD index to use */
+ int next_prod_idx;
+ int next_cons_idx;
+ int bd_count;
+};
+
+/* ENETC HW access info */
+struct enetc_devfn {
+ void *regs_base; /* base ENETC registers */
+ void *port_regs; /* base ENETC port registers */
+
+ /* Rx/Tx buffer descriptor rings info */
+ struct bd_ring tx_bdr;
+ struct bd_ring rx_bdr;
+};
+
+/* register accessors */
+#define enetc_read_reg(x) readl((x))
+#define enetc_write_reg(x, val) writel((val), (x))
+#define enetc_read(hw, off) enetc_read_reg((hw)->regs_base + (off))
+#define enetc_write(hw, off, v) enetc_write_reg((hw)->regs_base + (off), v)
+
+/* port register accessors */
+#define enetc_port_regs(hw, off) ((hw)->port_regs + (off))
+#define enetc_read_port(hw, off) enetc_read_reg(enetc_port_regs((hw), (off)))
+#define enetc_write_port(hw, off, v) \
+ enetc_write_reg(enetc_port_regs((hw), (off)), v)
+
+/* BDR register accessors, see ENETC_BDR() */
+#define enetc_bdr_read(hw, t, n, off) \
+ enetc_read(hw, ENETC_BDR(t, n, off))
+#define enetc_bdr_write(hw, t, n, off, val) \
+ enetc_write(hw, ENETC_BDR(t, n, off), val)
+
+#endif /* _ENETC_H */
diff --git a/include/pci_ids.h b/include/pci_ids.h
index bd59578ccb..06e1319366 100644
--- a/include/pci_ids.h
+++ b/include/pci_ids.h
@@ -2483,6 +2483,7 @@
#define PCI_DEVICE_ID_MPC8641 0x7010
#define PCI_DEVICE_ID_MPC8641D 0x7011
#define PCI_DEVICE_ID_MPC8610 0x7018
+#define PCI_DEVICE_ID_ENETC_PF_V1 0xE100
#define PCI_VENDOR_ID_PASEMI 0x1959
--
2.17.1
More information about the U-Boot
mailing list