[U-Boot] [PATCH] ARM: imx6q_logic: Cleanup boot sequence check

[Adam Ford]

The board_boot_order() function currenly assumes that the boot source
is MMC/eMMC, but this isn't true for the NAND devices.

This patch cleans up board_boot_order() to check for NAND, SD, ESD,
MMC or EMMC.  Anything beyond these are not supported, so it will
default back to the serial downloader if any of those devices are not
available.

Fixes: 9fb50c68daa6 ("ARM: imx6q_logic: Fix MMC2 booting")

Signed-off-by: Adam Ford <aford173 at gmail.com>

diff --git a/board/logicpd/imx6/imx6logic.c b/board/logicpd/imx6/imx6logic.c
index 3c1a3a9fa2..fc4ce34ce4 100644
--- a/board/logicpd/imx6/imx6logic.c
+++ b/board/logicpd/imx6/imx6logic.c
@@ -154,29 +154,49 @@ void board_boot_order(u32 *spl_boot_list)
 {
 	struct src *psrc = (struct src *)SRC_BASE_ADDR;
 	unsigned int reg = readl(&psrc->sbmr1) >> 11;
-	/*
-	 * Upon reading BOOT_CFG register the following map is done:
-	 * Bit 11 and 12 of BOOT_CFG register can determine the current
-	 * mmc port
-	 * 0x1                  SD1-SOM
-	 * 0x2                  SD2-Baseboard
-	 */
-
-	reg &= 0x3; /* Only care about bottom 2 bits */
-	switch (reg) {
-	case 0:
-		spl_boot_list[0] = BOOT_DEVICE_MMC1;
+	u32 boot_mode = imx6_src_get_boot_mode() & IMX6_BMODE_MASK;
+	unsigned int bmode = readl(&src_base->sbmr2);
+
+	/* If bmode is serial or USB phy is active, return serial */
+	if (((bmode >> 24) & 0x03) == 0x01 || is_usbotg_phy_active()) {
+		spl_boot_list[0] = BOOT_DEVICE_BOARD;
+		return;
+	}
+
+	switch (boot_mode >> IMX6_BMODE_SHIFT) {
+	case IMX6_BMODE_NAND_MIN ... IMX6_BMODE_NAND_MAX:
+		spl_boot_list[0] = BOOT_DEVICE_NAND;
 		break;
-	case 1:
-		spl_boot_list[0] = BOOT_DEVICE_MMC2;
+	case IMX6_BMODE_SD:
+	case IMX6_BMODE_ESD:
+	case IMX6_BMODE_MMC:
+	case IMX6_BMODE_EMMC:
+		/*
+		 * Upon reading BOOT_CFG register the following map is done:
+		 * Bit 11 and 12 of BOOT_CFG register can determine the current
+		 * mmc port
+		 * 0x1                  SD1-SOM
+		 * 0x2                  SD2-Baseboard
+		 */
+
+		reg &= 0x3; /* Only care about bottom 2 bits */
+		switch (reg) {
+		case 0:
+			spl_boot_list[0] = BOOT_DEVICE_MMC1;
+			break;
+		case 1:
+			spl_boot_list[0] = BOOT_DEVICE_MMC2;
+			break;
+		}
+		break;
+	default:
+		/* By default use USB downloader */
+		spl_boot_list[0] = BOOT_DEVICE_BOARD;
 		break;
 	}
 
-	/* If we cannot find a valid MMC/SD card, try NAND */
-	spl_boot_list[1] = BOOT_DEVICE_NAND;
-
 	/* As a last resort, use serial downloader */
-	spl_boot_list[2] = BOOT_DEVICE_BOARD;
+	spl_boot_list[1] = BOOT_DEVICE_BOARD;
 }
 
 static void ccgr_init(void)
-- 
2.20.1