[U-Boot] [PATCH] sun8i: h3: Support H3 variant of Orange Pi Zero Plus 2
Diego Rondini
diego.rondini at kynetics.com
Tue Nov 5 21:56:50 UTC 2019
Orangepi Zero Plus 2 is an open-source single-board computer, available
in two Allwinner SOC variants, H3 and H5. We add support for H3 variant
here, as the H5 is already supported.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Signed-off-by: Diego Rondini <diego.rondini at kynetics.com>
---
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts | 139 ++++++++++++++++++
board/sunxi/MAINTAINERS | 5 +
configs/orangepi_zero_plus2_h3_defconfig | 19 +++
4 files changed, 165 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
create mode 100644 configs/orangepi_zero_plus2_h3_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 251d32ca62..5c7b8cfcc9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -513,7 +513,8 @@ dtb-$(CONFIG_MACH_SUN8I_H3) += \
sun8i-h3-orangepi-pc.dtb \
sun8i-h3-orangepi-pc-plus.dtb \
sun8i-h3-orangepi-plus.dtb \
- sun8i-h3-orangepi-plus2e.dtb
+ sun8i-h3-orangepi-plus2e.dtb \
+ sun8i-h3-orangepi-zero-plus2.dtb
dtb-$(CONFIG_MACH_SUN8I_R40) += \
sun8i-r40-bananapi-m2-ultra.dtb \
sun8i-v40-bananapi-m2-berry.dtb
diff --git a/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
new file mode 100644
index 0000000000..f2f7b7a925
--- /dev/null
+++ b/arch/arm/dts/sun8i-h3-orangepi-zero-plus2.dts
@@ -0,0 +1,139 @@
+/*
+ * Copyright (C) 2017 Jagan Teki <jteki at openedev.com>
+ * Copyright (C) 2018 Diego Rondini <diego.rondini at kynetics.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "OrangePi Zero Plus2 H3";
+ compatible = "xunlong,orangepi-zero-plus2-h3", "allwinner,sun8i-h3";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */
+ post-power-on-delay-ms = <200>;
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&mmc1 {
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index a2adf89b5d..4a89bb0e7b 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -405,6 +405,11 @@ M: Jagan Teki <jagan at amarulasolutions.com>
S: Maintained
F: configs/orangepi_zero_plus2_defconfig
+ORANGEPI ZERO PLUS 2 H3 BOARD
+M: Diego Rondini <diego.rondini at kynetics.com>
+S: Maintained
+F: configs/orangepi_zero_plus2_h3_defconfig
+
ORANGEPI PC 2 BOARD
M: Andre Przywara <andre.przywara at arm.com>
S: Maintained
diff --git a/configs/orangepi_zero_plus2_h3_defconfig b/configs/orangepi_zero_plus2_h3_defconfig
new file mode 100644
index 0000000000..3000a97e73
--- /dev/null
+++ b/configs/orangepi_zero_plus2_h3_defconfig
@@ -0,0 +1,19 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SPL=y
+CONFIG_MACH_SUN8I_H3=y
+CONFIG_DRAM_CLK=672
+# CONFIG_DRAM_ODT_EN is not set
+CONFIG_MMC0_CD_PIN="PH13"
+CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_USE_PREBOOT=y
+# CONFIG_CMD_FLASH is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_SPL_EFI_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-h3-orangepi-zero-plus2"
+CONFIG_SUN8I_EMAC=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE=y
--
2.21.0
More information about the U-Boot
mailing list