[U-Boot] [PATCH v2] spl: Introduce SPL_DM_GPIO Kconfig define

[Lukasz Majewski]

Hi Simon,

> Hi Simon,
> 
> > Hi Lukasz,
> > 
> > On Mon, 14 Oct 2019 at 06:41, Lukasz Majewski <lukma at denx.de>
> > wrote:  
> > >
> > > Hi Simon,
> > >    
> > > > Hi Lukasz,
> > > >
> > > > On Wed, 9 Oct 2019 at 03:02, Lukasz Majewski <lukma at denx.de>
> > > > wrote:    
> > > > >
> > > > > Dear Tom,
> > > > >    
> > > > > > This define indicates if DM_GPIO shall be supported in SPL.
> > > > > > This allows proper operation of DM converted GPIO drivers in
> > > > > > SPL, which use boards.
> > > > > >
> > > > > > Signed-off-by: Lukasz Majewski <lukma at denx.de>
> > > > > > ---
> > > > > >
> > > > > > Changes in v2:
> > > > > > - Add dependency on DM_GPIO
> > > > > >    
> > > > >
> > > > > Tom, are there any issues preventing this patch from being
> > > > > applied to -master?    
> > > >
> > > > This does not actually define DM_GPIO anywhere though, so this
> > > > is unused.    
> > >
> > > The goal of this patch is to introduce in Kconfig a
> > > CONFIG_SPL_DM_GPIO. This define would be needed anyway, no matter
> > > if you perform the changes from [1].
> > >
> > > This Kconfig define is necessary for the XEA board (i.MX28 based
> > > one), which uses OF_PLATDATA in SPL excessively to fit into size
> > > constraints.
> > >
> > > To be more precise the mxs_gpio.c driver uses
> > > #if CONFIG_IS_ENABLED(DM_GPIO) to provide DM GPIO support in SPL
> > > with OF_PLATDATA.
> > >
> > >    
> > > >
> > > > As it happens I sent a similar patch[1], but it doesn't work.
> > > > I'll try again.    
> > >
> > > It would be great if we could have [1] not causing build breaks.
> > > However, for my used case it would be enough to have the Kconfig
> > > definition of CONFIG_SPL_DM_GPIO (as I'm using OF_PLATDATA) with
> > > it.
> > >
> > > Simon, if you don't have time to do the fix for [1] I would opt
> > > for pulling this patch (to just add proper Kconfig define).    
> > 
> > I have had a crack at this here:
> > 
> > https://gitlab.denx.de/u-boot/custodians/u-boot-dm/commit/a6d15bbd9e4e7684dd47d21817df85915f28cbab
> > 
> > I expect to send this series along with this patch at the end of
> > this week.  
> 
> If I may ask - have you made any progress on this?

In fact it blocks some i.MX28 related code (board to be precise) from
sending it upstream as converted drivers expect SPL_DM_GPIO to be
defined in Kconfig.

In fact I do just need following code:
https://patchwork.ozlabs.org/patch/1169013/

If you have some difficulties to solve (on e.g. other archs) then maybe
it would be enough to pull the above patch?

> 
> >   
> > >    
> > > >    
> > > > >    
> > > > > >  common/spl/Kconfig | 6 ++++++
> > > > > >  1 file changed, 6 insertions(+)
> > > > > >
> > > > > > diff --git a/common/spl/Kconfig b/common/spl/Kconfig
> > > > > > index f467eca2be..e3df8efa7e 100644
> > > > > > --- a/common/spl/Kconfig
> > > > > > +++ b/common/spl/Kconfig
> > > > > > @@ -452,6 +452,12 @@ config SPL_DMA_SUPPORT
> > > > > >         the CPU moving the data. Enable this option to build
> > > > > > the drivers in drivers/dma as part of an SPL build.
> > > > > >
> > > > > > +config SPL_DM_GPIO
> > > > > > +     bool "Support Driver Model GPIO drivers"
> > > > > > +     depends on SPL_GPIO_SUPPORT && DM_GPIO
> > > > > > +     help
> > > > > > +       Enable support for Driver Model based GPIO drivers
> > > > > > in SPL. +
> > > > > >  config SPL_DRIVERS_MISC_SUPPORT
> > > > > >       bool "Support misc drivers"
> > > > > >       help    
> > > > >    
> > > >
> > > > Regards,
> > > > SImon
> > > >
> > > > [1] http://patchwork.ozlabs.org/patch/1167276/    
> > >    
> > 
> > Regards,
> > Simon  
> 
> Best regards,
> 
> Lukasz Majewski
> 
> --
> 
> DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email:
> lukma at denx.de




Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: lukma at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 488 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20191117/cdbcf15b/attachment.sig>