[U-Boot] [PATCH v2 5/6] arm: dts: ls1028a: adds Ethernet switch node and its dependencies

[Alex Marginean]

The definition follows the DSA binding in kernel and describes the switch,
its ports and PHYs.
ENETC PF6 is the 2nd Eth controller linked to the switch on LS1028A, it is
not used in U-Boot and was disabled.

Signed-off-by: Alex Marginean <alexandru.marginean at nxp.com>
Tested-by: Michael Walle <michael at walle.cc>
---
 arch/arm/dts/fsl-ls1028a-rdb.dts | 36 ++++++++++++++++++++++++++
 arch/arm/dts/fsl-ls1028a.dtsi    | 44 +++++++++++++++++++++++++++++++-
 2 files changed, 79 insertions(+), 1 deletion(-)

diff --git a/arch/arm/dts/fsl-ls1028a-rdb.dts b/arch/arm/dts/fsl-ls1028a-rdb.dts
index 3d5e8ade21..700fc067a4 100644
--- a/arch/arm/dts/fsl-ls1028a-rdb.dts
+++ b/arch/arm/dts/fsl-ls1028a-rdb.dts
@@ -114,9 +114,45 @@
 	phy-handle = <&rdb_phy0>;
 };
 
+&ethsw_ports {
+	port at 0 {
+		status = "okay";
+		phy-mode = "qsgmii";
+		phy-handle = <&sw_phy0>;
+	};
+	port at 1 {
+		status = "okay";
+		phy-mode = "qsgmii";
+		phy-handle = <&sw_phy1>;
+	};
+	port at 2 {
+		status = "okay";
+		phy-mode = "qsgmii";
+		phy-handle = <&sw_phy2>;
+	};
+	port at 3 {
+		status = "okay";
+		phy-mode = "qsgmii";
+		phy-handle = <&sw_phy3>;
+	};
+};
+
 &mdio0 {
 	status = "okay";
 	rdb_phy0: phy at 2 {
 		reg = <2>;
 	};
+
+	sw_phy0: phy at 10 {
+		reg = <0x10>;
+	};
+	sw_phy1: phy at 11 {
+		reg = <0x11>;
+	};
+	sw_phy2: phy at 12 {
+		reg = <0x12>;
+	};
+	sw_phy3: phy at 13 {
+		reg = <0x13>;
+	};
 };
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi
index 43a154e8e7..97c7d4de4d 100644
--- a/arch/arm/dts/fsl-ls1028a.dtsi
+++ b/arch/arm/dts/fsl-ls1028a.dtsi
@@ -136,9 +136,51 @@
 			reg = <0x000300 0 0 0 0>;
 			status = "disabled";
 		};
+		ethsw: pci at 0,5 {
+			#address-cells=<0>;
+			#size-cells=<1>;
+			reg = <0x000500 0 0 0 0>;
+
+			ethsw_ports: ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port at 0 {
+					reg = <0>;
+					status = "disabled";
+					label = "swp0";
+				};
+				port at 1 {
+					reg = <1>;
+					status = "disabled";
+					label = "swp1";
+				};
+				port at 2 {
+					reg = <2>;
+					status = "disabled";
+					label = "swp2";
+				};
+				port at 3 {
+					reg = <3>;
+					status = "disabled";
+					label = "swp3";
+				};
+				port at 4 {
+					reg = <4>;
+					phy-mode = "internal";
+					status = "okay";
+					ethernet = <&enetc2>;
+				};
+				port at 5 {
+					reg = <5>;
+					phy-mode = "internal";
+					status = "disabled";
+				};
+			};
+		};
 		enetc6: pci at 0,6 {
 			reg = <0x000600 0 0 0 0>;
-			status = "okay";
+			status = "disabled";
 			phy-mode = "internal";
 		};
 	};
-- 
2.17.1