[U-Boot] [PATCH v5 19/19] arm: socfpga: agilex: Enable Agilex SoC build
Simon Goldschmidt
simon.k.r.goldschmidt at gmail.com
Tue Oct 22 18:42:03 UTC 2019
Am 11.10.2019 um 11:52 schrieb Ley Foon Tan:
> Add build support for Agilex SoC.
>
> Signed-off-by: Ley Foon Tan <ley.foon.tan at intel.com>
> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt at gmail.com>
This does not apply any more, you'll need to rebase it (Marek has
changed mach-socfpga/Kconfig by renaming a board).
Regards,
Simon
>
> ---
> v5:
> - Enable NCORE_CACHE
>
> v3:
> - Disable CONFIG_USE_TINY_PRINTF
>
> v2:
> - Remove IC_CLK define, use clock DM method to get i2c clock
> - Change CONFIG_ENV_SIZE to 4KB since CONFIG_SPI_FLASH_USE_4K_SECTORS is enabled.
> ---
> arch/arm/Kconfig | 4 +-
> arch/arm/mach-socfpga/Kconfig | 16 ++
> arch/arm/mach-socfpga/Makefile | 9 ++
> configs/socfpga_agilex_defconfig | 59 +++++++
> include/configs/socfpga_agilex_socdk.h | 207 +++++++++++++++++++++++++
> 5 files changed, 293 insertions(+), 2 deletions(-)
> create mode 100644 configs/socfpga_agilex_defconfig
> create mode 100644 include/configs/socfpga_agilex_socdk.h
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 3b0e315061..e6c9d19968 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -888,7 +888,7 @@ config ARCH_SOCFPGA
> bool "Altera SOCFPGA family"
> select ARCH_EARLY_INIT_R
> select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10
> - select ARM64 if TARGET_SOCFPGA_STRATIX10
> + select ARM64 if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX
> select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
> select DM
> select DM_SERIAL
> @@ -900,7 +900,7 @@ config ARCH_SOCFPGA
> select SPL_LIBGENERIC_SUPPORT
> select SPL_NAND_SUPPORT if SPL_NAND_DENALI
> select SPL_OF_CONTROL
> - select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
> + select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10 || TARGET_SOCFPGA_AGILEX
> select SPL_SERIAL_SUPPORT
> select SPL_SYSRESET
> select SPL_WATCHDOG_SUPPORT
> diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
> index 1d914648e3..3f5c4b357f 100644
> --- a/arch/arm/mach-socfpga/Kconfig
> +++ b/arch/arm/mach-socfpga/Kconfig
> @@ -26,6 +26,15 @@ config SYS_TEXT_BASE
> default 0x01000040 if TARGET_SOCFPGA_ARRIA10
> default 0x01000040 if TARGET_SOCFPGA_GEN5
>
> +config TARGET_SOCFPGA_AGILEX
> + bool
> + select ARMV8_MULTIENTRY
> + select ARMV8_SET_SMPEN
> + select ARMV8_SPIN_TABLE
> + select CLK
> + select NCORE_CACHE
> + select SPL_CLK if SPL
> +
> config TARGET_SOCFPGA_ARRIA5
> bool
> select TARGET_SOCFPGA_GEN5
> @@ -72,6 +81,10 @@ choice
> prompt "Altera SOCFPGA board select"
> optional
>
> +config TARGET_SOCFPGA_AGILEX_SOCDK
> + bool "Intel SOCFPGA SoCDK (Agilex)"
> + select TARGET_SOCFPGA_AGILEX
> +
> config TARGET_SOCFPGA_ARIES_MCVEVK
> bool "Aries MCVEVK (Cyclone V)"
> select TARGET_SOCFPGA_CYCLONE5
> @@ -132,6 +145,7 @@ config TARGET_SOCFPGA_TERASIC_SOCKIT
> endchoice
>
> config SYS_BOARD
> + default "agilex-socdk" if TARGET_SOCFPGA_AGILEX_SOCDK
> default "arria5-socdk" if TARGET_SOCFPGA_ARRIA5_SOCDK
> default "arria10-socdk" if TARGET_SOCFPGA_ARRIA10_SOCDK
> default "cyclone5-socdk" if TARGET_SOCFPGA_CYCLONE5_SOCDK
> @@ -148,6 +162,7 @@ config SYS_BOARD
> default "vining_fpga" if TARGET_SOCFPGA_SAMTEC_VINING_FPGA
>
> config SYS_VENDOR
> + default "intel" if TARGET_SOCFPGA_AGILEX_SOCDK
> default "altera" if TARGET_SOCFPGA_ARRIA5_SOCDK
> default "altera" if TARGET_SOCFPGA_ARRIA10_SOCDK
> default "altera" if TARGET_SOCFPGA_CYCLONE5_SOCDK
> @@ -165,6 +180,7 @@ config SYS_SOC
> default "socfpga"
>
> config SYS_CONFIG_NAME
> + default "socfpga_agilex_socdk" if TARGET_SOCFPGA_AGILEX_SOCDK
> default "socfpga_arria5_socdk" if TARGET_SOCFPGA_ARRIA5_SOCDK
> default "socfpga_arria10_socdk" if TARGET_SOCFPGA_ARRIA10_SOCDK
> default "socfpga_cyclone5_socdk" if TARGET_SOCFPGA_CYCLONE5_SOCDK
> diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile
> index 81b6ffc675..418f543b20 100644
> --- a/arch/arm/mach-socfpga/Makefile
> +++ b/arch/arm/mach-socfpga/Makefile
> @@ -41,6 +41,14 @@ endif
>
> ifdef CONFIG_TARGET_SOCFPGA_AGILEX
> obj-y += clock_manager_agilex.o
> +obj-y += mailbox_s10.o
> +obj-y += misc_s10.o
> +obj-y += mmu-arm64_s10.o
> +obj-y += reset_manager_s10.o
> +obj-y += system_manager_s10.o
> +obj-y += timer_s10.o
> +obj-y += wrap_pinmux_config_s10.o
> +obj-y += wrap_pll_config_s10.o
> endif
>
> ifdef CONFIG_SPL_BUILD
> @@ -59,6 +67,7 @@ obj-y += firewall.o
> obj-y += spl_s10.o
> endif
> ifdef CONFIG_TARGET_SOCFPGA_AGILEX
> +obj-y += firewall.o
> obj-y += spl_agilex.o
> endif
> endif
> diff --git a/configs/socfpga_agilex_defconfig b/configs/socfpga_agilex_defconfig
> new file mode 100644
> index 0000000000..daf71ff0eb
> --- /dev/null
> +++ b/configs/socfpga_agilex_defconfig
> @@ -0,0 +1,59 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_SOCFPGA=y
> +CONFIG_SYS_TEXT_BASE=0x1000
> +CONFIG_SYS_MALLOC_F_LEN=0x2000
> +CONFIG_NR_DRAM_BANKS=2
> +CONFIG_TARGET_SOCFPGA_AGILEX_SOCDK=y
> +CONFIG_IDENT_STRING="socfpga_agilex"
> +CONFIG_SPL_FS_FAT=y
> +CONFIG_SPL_TEXT_BASE=0xFFE00000
> +CONFIG_BOOTDELAY=5
> +CONFIG_SPL_SPI_LOAD=y
> +CONFIG_SYS_SPI_U_BOOT_OFFS=0x3c00000
> +CONFIG_HUSH_PARSER=y
> +CONFIG_SYS_PROMPT="SOCFPGA_AGILEX # "
> +CONFIG_CMD_MEMTEST=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_SF=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_DHCP=y
> +CONFIG_CMD_MII=y
> +CONFIG_CMD_PING=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_EXT4=y
> +CONFIG_CMD_FAT=y
> +CONFIG_CMD_FS_GENERIC=y
> +CONFIG_OF_EMBED=y
> +CONFIG_DEFAULT_DEVICE_TREE="socfpga_agilex_socdk"
> +CONFIG_ENV_IS_IN_MMC=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_SPL_ALTERA_SDRAM=y
> +CONFIG_DM_GPIO=y
> +CONFIG_DWAPB_GPIO=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_DW=y
> +CONFIG_DM_MMC=y
> +CONFIG_MMC_DW=y
> +CONFIG_SPI_FLASH=y
> +CONFIG_SF_DEFAULT_MODE=0x2003
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_PHY_MICREL=y
> +CONFIG_PHY_MICREL_KSZ90X1=y
> +CONFIG_DM_ETH=y
> +CONFIG_ETH_DESIGNWARE=y
> +CONFIG_MII=y
> +CONFIG_DM_RESET=y
> +CONFIG_SPI=y
> +CONFIG_CADENCE_QSPI=y
> +CONFIG_DESIGNWARE_SPI=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_DWC2=y
> +CONFIG_USB_STORAGE=y
> +# CONFIG_USE_TINY_PRINTF is not set
> diff --git a/include/configs/socfpga_agilex_socdk.h b/include/configs/socfpga_agilex_socdk.h
> new file mode 100644
> index 0000000000..8ed96ed252
> --- /dev/null
> +++ b/include/configs/socfpga_agilex_socdk.h
> @@ -0,0 +1,207 @@
> +/* SPDX-License-Identifier: GPL-2.0
> + *
> + * Copyright (C) 2019 Intel Corporation <www.intel.com>
> + *
> + */
> +
> +#ifndef __CONFIG_SOCFGPA_AGILEX_H__
> +#define __CONFIG_SOCFGPA_AGILEX_H__
> +
> +#include <asm/arch/base_addr_s10.h>
> +#include <asm/arch/handoff_s10.h>
> +
> +/*
> + * U-Boot general configurations
> + */
> +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
> +#define CONFIG_LOADADDR 0x2000000
> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> +#define CONFIG_REMAKE_ELF
> +/* sysmgr.boot_scratch_cold4 & 5 (64bit) will be used for PSCI_CPU_ON call */
> +#define CPU_RELEASE_ADDR 0xFFD12210
> +#define CONFIG_SYS_CACHELINE_SIZE 64
> +#define CONFIG_SYS_MEM_RESERVE_SECURE 0 /* using OCRAM, not DDR */
> +
> +/*
> + * U-Boot console configurations
> + */
> +#define CONFIG_SYS_MAXARGS 64
> +#define CONFIG_SYS_CBSIZE 2048
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
> + sizeof(CONFIG_SYS_PROMPT) + 16)
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> +
> +/* Extend size of kernel image for uncompression */
> +#define CONFIG_SYS_BOOTM_LEN (32 * 1024 * 1024)
> +
> +/*
> + * U-Boot run time memory configurations
> + */
> +#define CONFIG_SYS_INIT_RAM_ADDR 0xFFE00000
> +#define CONFIG_SYS_INIT_RAM_SIZE 0x40000
> +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR \
> + + CONFIG_SYS_INIT_RAM_SIZE \
> + - S10_HANDOFF_SIZE)
> +#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_SP_ADDR)
> +#define CONFIG_SYS_MALLOC_LEN (5 * 1024 * 1024)
> +
> +/*
> + * U-Boot environment configurations
> + */
> +#define CONFIG_ENV_SIZE 0x1000
> +#define CONFIG_SYS_MMC_ENV_DEV 0 /* device 0 */
> +#define CONFIG_ENV_OFFSET 512 /* just after the MBR */
> +
> +/*
> + * QSPI support
> + */
> + #ifdef CONFIG_CADENCE_QSPI
> +/* Enable it if you want to use dual-stacked mode */
> +/*#define CONFIG_QSPI_RBF_ADDR 0x720000*/
> +
> +/* Flash device info */
> +
> +/*#define CONFIG_ENV_IS_IN_SPI_FLASH*/
> +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
> +#undef CONFIG_ENV_OFFSET
> +#undef CONFIG_ENV_SIZE
> +#define CONFIG_ENV_OFFSET 0x710000
> +#define CONFIG_ENV_SIZE (4 * 1024)
> +#define CONFIG_ENV_SECT_SIZE (4 * 1024)
> +#endif /* CONFIG_ENV_IS_IN_SPI_FLASH */
> +
> +#ifndef CONFIG_SPL_BUILD
> +#define CONFIG_MTD_DEVICE
> +#define CONFIG_MTD_PARTITIONS
> +#define MTDIDS_DEFAULT "nor0=ff705000.spi.0"
> +#endif /* CONFIG_SPL_BUILD */
> +
> +#ifndef __ASSEMBLY__
> +unsigned int cm_get_qspi_controller_clk_hz(void);
> +#define CONFIG_CQSPI_REF_CLK cm_get_qspi_controller_clk_hz()
> +#endif
> +
> +#endif /* CONFIG_CADENCE_QSPI */
> +
> +/*
> + * Boot arguments passed to the boot command. The value of
> + * CONFIG_BOOTARGS goes into the environment value "bootargs".
> + * Do note the value will override also the chosen node in FDT blob.
> + */
> +#define CONFIG_BOOTARGS "earlycon"
> +#define CONFIG_BOOTCOMMAND "run fatscript; run mmcload;run linux_qspi_enable;" \
> + "run mmcboot"
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "loadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
> + "bootfile=Image\0" \
> + "fdt_addr=8000000\0" \
> + "fdtimage=socfpga_agilex_socdk.dtb\0" \
> + "mmcroot=/dev/mmcblk0p2\0" \
> + "mmcboot=setenv bootargs " CONFIG_BOOTARGS \
> + " root=${mmcroot} rw rootwait;" \
> + "booti ${loadaddr} - ${fdt_addr}\0" \
> + "mmcload=mmc rescan;" \
> + "load mmc 0:1 ${loadaddr} ${bootfile};" \
> + "load mmc 0:1 ${fdt_addr} ${fdtimage}\0" \
> + "linux_qspi_enable=if sf probe; then " \
> + "echo Enabling QSPI at Linux DTB...;" \
> + "fdt addr ${fdt_addr}; fdt resize;" \
> + "fdt set /soc/spi at ff8d2000 status okay;" \
> + "fdt set /soc/clkmgr/clocks/qspi_clk clock-frequency " \
> + " ${qspi_clock}; fi; \0" \
> + "scriptaddr=0x02100000\0" \
> + "scriptfile=u-boot.scr\0" \
> + "fatscript=if fatload mmc 0:1 ${scriptaddr} ${scriptfile};" \
> + "then source ${scriptaddr}; fi\0"
> +
> +/*
> + * Generic Interrupt Controller Definitions
> + */
> +#define CONFIG_GICV2
> +
> +/*
> + * External memory configurations
> + */
> +#define PHYS_SDRAM_1 0x0
> +#define PHYS_SDRAM_1_SIZE (1 * 1024 * 1024 * 1024)
> +#define CONFIG_SYS_SDRAM_BASE 0
> +#define CONFIG_SYS_MEMTEST_START 0
> +#define CONFIG_SYS_MEMTEST_END PHYS_SDRAM_1_SIZE - 0x200000
> +
> +/*
> + * Serial / UART configurations
> + */
> +#define CONFIG_SYS_NS16550_CLK 100000000
> +#define CONFIG_SYS_NS16550_MEM32
> +
> +/*
> + * Timer & watchdog configurations
> + */
> +#define COUNTER_FREQUENCY 400000000
> +
> +/*
> + * SDMMC configurations
> + */
> +#ifdef CONFIG_CMD_MMC
> +#define CONFIG_SYS_MMC_MAX_BLK_COUNT 256
> +#endif
> +/*
> + * Flash configurations
> + */
> +#define CONFIG_SYS_MAX_FLASH_BANKS 1
> +
> +/* Ethernet on SoC (EMAC) */
> +#if defined(CONFIG_CMD_NET)
> +#define CONFIG_DW_ALTDESCRIPTOR
> +#endif /* CONFIG_CMD_NET */
> +
> +/*
> + * L4 Watchdog
> + */
> +#ifdef CONFIG_SPL_BUILD
> +#define CONFIG_HW_WATCHDOG
> +#define CONFIG_DESIGNWARE_WATCHDOG
> +#define CONFIG_DW_WDT_BASE SOCFPGA_L4WD0_ADDRESS
> +#ifndef __ASSEMBLY__
> +#define CONFIG_DW_WDT_CLOCK_KHZ 100000
> +#endif
> +#define CONFIG_WATCHDOG_TIMEOUT_MSECS 3000
> +#endif
> +
> +/*
> + * SPL memory layout
> + *
> + * On chip RAM
> + * 0xFFE0_0000 ...... Start of OCRAM
> + * SPL code, rwdata
> + * empty space
> + * 0xFFEx_xxxx ...... Top of stack (grows down)
> + * 0xFFEy_yyyy ...... Global Data
> + * 0xFFEz_zzzz ...... Malloc prior relocation (size CONFIG_SYS_MALLOC_F_LEN)
> + * 0xFFE3_F000 ...... Hardware handdoff blob (size 4KB)
> + * 0xFFE3_FFFF ...... End of OCRAM
> + *
> + * SDRAM
> + * 0x0000_0000 ...... Start of SDRAM_1
> + * unused / empty space for image loading
> + * Size 64MB ...... MALLOC (size CONFIG_SYS_SPL_MALLOC_SIZE)
> + * Size 1MB ...... BSS (size CONFIG_SPL_BSS_MAX_SIZE)
> + * 0x8000_0000 ...... End of SDRAM_1 (assume 2GB)
> + *
> + */
> +#define CONFIG_SPL_TARGET "spl/u-boot-spl.hex"
> +#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_INIT_RAM_SIZE
> +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
> +#define CONFIG_SPL_BSS_MAX_SIZE 0x100000 /* 1 MB */
> +#define CONFIG_SPL_BSS_START_ADDR (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE \
> + - CONFIG_SPL_BSS_MAX_SIZE)
> +#define CONFIG_SYS_SPL_MALLOC_SIZE (CONFIG_SYS_MALLOC_LEN)
> +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR \
> + - CONFIG_SYS_SPL_MALLOC_SIZE)
> +
> +/* SPL SDMMC boot support */
> +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
> +#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
> +
> +#endif /* __CONFIG_H */
>
More information about the U-Boot
mailing list