[U-Boot] [PATCH v3] imx: Add support for i.MX28 based XEA board
Lukasz Majewski
lukma at denx.de
Thu Sep 5 12:49:13 UTC 2019
From: Mans Rullgard <mans at mansr.com>
This patch introduces support for i.MX28 based XEA board.
This board supports DM/DTS in U-Boot proper as well as DM aware drivers
in SPL (u-boot.sb).
More detailed information regarding usage of it can be found in
./board/liebherr/xea/README file.
U-Boot SPL 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
Trying to boot from MMC1
MMC0: Command 8 timeout (status 0xf0344020)
mmc_load_image_raw_sector: mmc block read error
U-Boot 2019.10-rc1-00233-g6aa549f05c (Aug 12 2019 - 09:23:36 +0200)
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SPI #3, master, 3V3 NOR
Model: Liebherr (LWE) XEA i.MX28 Board
DRAM: 128 MiB
MMC: MXS MMC: 0
Loading Environment from SPI Flash... SF: Detected n25q128a13 with page size 256 Bytes, erase size 64 KiB, total 16 MiB
OK
In: serial
Out: serial
Err: serial
Net:
Warning: ethernet at 800f0000 (eth0) using random MAC address - ce:e1:9e:46:f3:a2
eth0: ethernet at 800f0000
Hit any key to stop autoboot: 0
Signed-off-by: Mans Rullgard <mans at mansr.com>
Signed-off-by: Lukasz Majewski <lukma at denx.de>
---
Changes in v3:
- Use Kconfig defined option (CONFIG_FS_EXT4) instead of the one defined
in xea.h
- Use Kconfig defined option (CONFIG_SYS_SPI_U_BOOT_OFFS) instead of the one
defined in xea.h
- Provide correct SDPX header for xea.h
Changes in v2:
- Adjust config to match dependent patches
- Increase malloc size to allow booting the board with GPIO DM/DTS support
- Add support for GPIO driver in SPL (with DM + OF_PLATDATA)
- Adjust spl_xea.c to support bootmode pins
- Add patches to set in Kconfig default boot HW partition for eMMC
Dependencies:
- The whole patch series (v3) (1-3) starting at:
https://patchwork.ozlabs.org/cover/1158144/
(Conversion of DM_SPI to (SPL_TPL_)_DM_SPI)
- Fixes/conversion for i.MX28 spi, emmc and gpio (the whole series 1-7):
https://patchwork.ozlabs.org/cover/1158255/
Applied on top of -master branch:
SHA1: 448f11f7503995746a7b71e5e3b3a831c4651be9
---
arch/arm/dts/Makefile | 3 +
arch/arm/dts/imx28-xea-u-boot.dtsi | 46 ++++++
arch/arm/dts/imx28-xea.dts | 110 ++++++++++++++
arch/arm/mach-imx/mxs/Kconfig | 4 +
board/liebherr/xea/Kconfig | 24 +++
board/liebherr/xea/MAINTAINERS | 6 +
board/liebherr/xea/Makefile | 12 ++
board/liebherr/xea/README | 63 ++++++++
board/liebherr/xea/spl_xea.c | 303 +++++++++++++++++++++++++++++++++++++
board/liebherr/xea/xea.c | 152 +++++++++++++++++++
configs/imx28_xea_defconfig | 110 ++++++++++++++
include/configs/xea.h | 192 +++++++++++++++++++++++
12 files changed, 1025 insertions(+)
create mode 100644 arch/arm/dts/imx28-xea-u-boot.dtsi
create mode 100644 arch/arm/dts/imx28-xea.dts
create mode 100644 board/liebherr/xea/Kconfig
create mode 100644 board/liebherr/xea/MAINTAINERS
create mode 100644 board/liebherr/xea/Makefile
create mode 100644 board/liebherr/xea/README
create mode 100644 board/liebherr/xea/spl_xea.c
create mode 100644 board/liebherr/xea/xea.c
create mode 100644 configs/imx28_xea_defconfig
create mode 100644 include/configs/xea.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index aac1b83d49..82a0379c13 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -547,6 +547,9 @@ dtb-$(CONFIG_VF610) += vf500-colibri.dtb \
vf610-pcm052.dtb \
vf610-bk4r1.dtb
+dtb-$(CONFIG_MX28) += \
+ imx28-xea.dtb
+
dtb-$(CONFIG_MX53) += imx53-cx9020.dtb \
imx53-kp.dtb \
imx53-m53menlo.dtb
diff --git a/arch/arm/dts/imx28-xea-u-boot.dtsi b/arch/arm/dts/imx28-xea-u-boot.dtsi
new file mode 100644
index 0000000000..cc2ced5d2d
--- /dev/null
+++ b/arch/arm/dts/imx28-xea-u-boot.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ */
+
+/*
+ * The minimal augmentation DTS U-Boot file to allow eMMC driver
+ * configuration in SPL for falcon boot.
+ */
+#include "imx28-u-boot.dtsi"
+/ {
+ apb at 80000000 {
+ u-boot,dm-spl;
+
+ apbh at 80000000 {
+ u-boot,dm-spl;
+ };
+
+ apbx at 80040000 {
+ u-boot,dm-spl;
+ };
+ };
+};
+
+&clks {
+ u-boot,dm-spl;
+};
+
+&gpio0 {
+ u-boot,dm-spl;
+};
+
+&pinctrl {
+ u-boot,dm-spl;
+};
+
+&ssp0 {
+ u-boot,dm-spl;
+};
+
+&ssp3 {
+ u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/imx28-xea.dts b/arch/arm/dts/imx28-xea.dts
new file mode 100644
index 0000000000..5de6774c5a
--- /dev/null
+++ b/arch/arm/dts/imx28-xea.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * SPDX-License-Identifier: GPL-2.0+ or X11
+ *
+ */
+
+/dts-v1/;
+
+#include "imx28.dtsi"
+
+/ {
+ model = "Liebherr (LWE) XEA i.MX28 Board";
+ compatible = "lwe,xea", "fsl,imx28";
+
+ aliases {
+ spi3 = &ssp3;
+ };
+
+ memory at 40000000 {
+ device_type = "memory";
+ reg = <0x40000000 0x10000000>;
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_fec_3v3: regulator-fec-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "fec-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&mac0 {
+ phy-mode = "rmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mac0_pins_a>;
+ phy-supply = <®_fec_3v3>;
+ phy-reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <1>;
+ phy-reset-post-delay = <1>;
+ status = "okay";
+
+ fixed-link {
+ speed = <100>;
+ full-duplex;
+ };
+};
+
+&ssp0 {
+ compatible = "fsl,imx28-mmc";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_8bit_pins_a>;
+ bus-width = <8>;
+ vmmc-supply = <®_3p3v>;
+ non-removable;
+ status = "okay";
+};
+
+&ssp3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx28-spi";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_pins_b>;
+ status = "okay";
+ spi-max-frequency = <40000000>;
+ num-cs = <2>;
+
+ flash0: s25fl256s at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <40000000>;
+ reg = <0>;
+
+ partition at 0 {
+ label = "SPL (spi)";
+ reg = <0x0 0x10000>;
+ read-only;
+ };
+ partition at 1 {
+ label = "u-boot (spi)";
+ reg = <0x10000 0x70000>;
+ read-only;
+ };
+ partition at 2 {
+ label = "uboot-env (spi)";
+ reg = <0x80000 0x20000>;
+ };
+ partition at 3 {
+ label = "kernel (spi)";
+ reg = <0x100000 0x400000>;
+ };
+ partition at 4 {
+ label = "swupdate (spi)";
+ reg = <0x50000 0x800000>;
+ };
+ };
+};
diff --git a/arch/arm/mach-imx/mxs/Kconfig b/arch/arm/mach-imx/mxs/Kconfig
index 68072d5a1f..b90d7b6e41 100644
--- a/arch/arm/mach-imx/mxs/Kconfig
+++ b/arch/arm/mach-imx/mxs/Kconfig
@@ -60,6 +60,9 @@ config TARGET_SC_SPS_1
config TARGET_TS4600
bool "Support TS4600"
+config TARGET_XEA
+ bool "Support XEA"
+
endchoice
config SYS_SOC
@@ -67,6 +70,7 @@ config SYS_SOC
source "board/bluegiga/apx4devkit/Kconfig"
source "board/freescale/mx28evk/Kconfig"
+source "board/liebherr/xea/Kconfig"
source "board/ppcag/bg0900/Kconfig"
source "board/schulercontrol/sc_sps_1/Kconfig"
source "board/technologic/ts4600/Kconfig"
diff --git a/board/liebherr/xea/Kconfig b/board/liebherr/xea/Kconfig
new file mode 100644
index 0000000000..5428de4646
--- /dev/null
+++ b/board/liebherr/xea/Kconfig
@@ -0,0 +1,24 @@
+if TARGET_XEA
+
+config SYS_BOARD
+ default "xea"
+
+config SYS_VENDOR
+ default "liebherr"
+
+config SYS_SOC
+ default "mxs"
+
+config SYS_CONFIG_NAME
+ default "xea"
+
+config ENV_SIZE
+ default 0x2000
+
+config ENV_SECT_SIZE
+ default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+ default 0x80000 if ENV_IS_IN_SPI_FLASH
+
+endif
diff --git a/board/liebherr/xea/MAINTAINERS b/board/liebherr/xea/MAINTAINERS
new file mode 100644
index 0000000000..623184d0f8
--- /dev/null
+++ b/board/liebherr/xea/MAINTAINERS
@@ -0,0 +1,6 @@
+XEA BOARD
+M: Lukasz Majewski <lukma at denx.de>
+S: Maintained
+F: board/liebherr/xea/
+F: include/configs/xea.h
+F: configs/imx28_xea_defconfig
diff --git a/board/liebherr/xea/Makefile b/board/liebherr/xea/Makefile
new file mode 100644
index 0000000000..abf500857f
--- /dev/null
+++ b/board/liebherr/xea/Makefile
@@ -0,0 +1,12 @@
+#
+# (C) Copyright 2019
+# Lukasz Majewski, DENX Software Engineering, lukma at denx.de.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := xea.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl_xea.o
+endif
diff --git a/board/liebherr/xea/README b/board/liebherr/xea/README
new file mode 100644
index 0000000000..3e55d3ea43
--- /dev/null
+++ b/board/liebherr/xea/README
@@ -0,0 +1,63 @@
+Building SPL/U-Boot for xea board
+=================================
+
+Setup environment, configure and build, e.g. by:
+
+ $ make imx28_xea_defconfig
+ $ make -j4 u-boot.sb u-boot.img
+
+Now you should see u-boot.sb and u-boot.img files in the build directory.
+
+
+Booting
+=======
+
+The boot ROM loads SPL from SPI NOR flash into SRAM. SPL configures
+DRAM and loads either a Linux kernel (falcon mode) or, if the rescue
+pin is asserted, the main U-Boot. Both kernel and U-Boot reside in
+eMMC boot partition 0. For redundancy, a copy of U-Boot is also
+stored in SPI flash. If a valid kernel image is not found, U-Boot is
+loaded from eMMC or, if this fails, SPI flash.
+
+Boot area layout
+----------------
+
+SPI NOR
+Offset Function File
+------------------------------------------
+0x00000000 SPL u-boot.sb
+0x00010000 U-Boot u-boot.img
+0x00080000 Environment
+
+eMMC
+Offset Function File
+------------------------------------------
+0x00000000 U-Boot u-boot.img
+0x00080000 Devicetree imx28-bttc.dtb
+0x00100000 Kernel uImage
+
+
+Falcon mode
+===========
+
+In falcon mode, the default, SPL loads the kernel and devicetree
+directly. For this to work, the stored devicetree must include
+correct "memory" and "chosen" nodes as these are not updated by SPL
+before booting the kernel.
+
+
+Updating from U-Boot
+====================
+
+The default U-Boot environment includes command sequences to update
+SPL, U-Boot, and kernel over TFTP. These are as follows:
+
+- update_spl: writes u-boot.sb to SPI NOR
+- update_uboot: writes u-boot.img to eMMC and SPI NOR
+- update_kernel: writes kernel and devicetree to eMMC
+
+They can be invoked at the U-Boot prompt using the "run" command,
+e.g. "run update_spl" to update the SPL.
+
+These update commands download the above-named files from the
+${hostname} directory on the server provided by DHCP.
diff --git a/board/liebherr/xea/spl_xea.c b/board/liebherr/xea/spl_xea.c
new file mode 100644
index 0000000000..d88b75bb3a
--- /dev/null
+++ b/board/liebherr/xea/spl_xea.c
@@ -0,0 +1,303 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * DENX M28 Boot setup
+ *
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans at mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut at gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/sys_proto.h>
+
+#define MUX_CONFIG_LCD (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_NOPULL)
+#define MUX_CONFIG_BOOT (MXS_PAD_3V3 | MXS_PAD_PULLUP)
+#define MUX_CONFIG_TSC (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_SSP0 (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_SSP2 (MXS_PAD_3V3 | MXS_PAD_4MA | MXS_PAD_PULLUP)
+#define MUX_CONFIG_ENET (MXS_PAD_3V3 | MXS_PAD_8MA | MXS_PAD_NOPULL)
+#define MUX_CONFIG_EMI (MXS_PAD_3V3 | MXS_PAD_12MA | MXS_PAD_NOPULL)
+
+const iomux_cfg_t iomux_setup[] = {
+ /* AUART0 IRDA */
+ MX28_PAD_AUART0_RX__AUART0_RX,
+ MX28_PAD_AUART0_TX__AUART0_TX,
+
+ /* AUART 4 RS422 */
+ MX28_PAD_AUART0_CTS__AUART4_RX,
+ MX28_PAD_AUART0_RTS__AUART4_TX,
+
+ /* USB0 */
+ MX28_PAD_AUART1_CTS__USB0_OVERCURRENT,
+ MX28_PAD_AUART1_RTS__USB0_ID,
+ MX28_PAD_LCD_VSYNC__GPIO_1_28, /* PRW_On */
+
+ /* USB1 */
+ MX28_PAD_PWM2__USB1_OVERCURRENT,
+
+ /* eMMC */
+ MX28_PAD_SSP0_CMD__SSP0_CMD | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA0__SSP0_D0 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA1__SSP0_D1 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA2__SSP0_D2 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA3__SSP0_D3 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA4__SSP0_D4 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA5__SSP0_D5 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA6__SSP0_D6 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DATA7__SSP0_D7 | MUX_CONFIG_SSP0,
+ MX28_PAD_SSP0_DETECT__GPIO_2_9, /* Reset for eMMC */
+ MX28_PAD_SSP0_SCK__SSP0_SCK | MUX_CONFIG_SSP0,
+
+ /* DIG Keys */
+ MX28_PAD_GPMI_D00__GPIO_0_0,
+ MX28_PAD_GPMI_D01__GPIO_0_1,
+ MX28_PAD_GPMI_D02__GPIO_0_2,
+ MX28_PAD_GPMI_D03__GPIO_0_3,
+ MX28_PAD_GPMI_D04__GPIO_0_4,
+ MX28_PAD_GPMI_D05__GPIO_0_5,
+ MX28_PAD_GPMI_D06__GPIO_0_6,
+ MX28_PAD_GPMI_D07__GPIO_0_7,
+
+ /* ADR_0-2 */
+ MX28_PAD_GPMI_CE1N__GPIO_0_17,
+ MX28_PAD_GPMI_CE2N__GPIO_0_18,
+ MX28_PAD_GPMI_CE3N__GPIO_0_19,
+
+ /* Read Keys */
+ MX28_PAD_GPMI_RDY0__GPIO_0_20,
+
+ /* LATCH_EN */
+ MX28_PAD_GPMI_RDY1__GPIO_0_21,
+
+ /* Power off */
+ MX28_PAD_GPMI_RDN__GPIO_0_24,
+
+ /* I2C1 Touch */
+ MX28_PAD_AUART2_CTS__GPIO_3_10,
+ MX28_PAD_AUART2_RTS__GPIO_3_11,
+ MX28_PAD_GPMI_RDY2__GPIO_0_22, /* Touch Reset */
+
+ /* TIVA */
+ MX28_PAD_AUART1_RX__SSP2_CARD_DETECT,
+ MX28_PAD_SSP2_MISO__SSP2_D0,
+ MX28_PAD_SSP2_MOSI__SSP2_CMD,
+ MX28_PAD_SSP2_SCK__SSP2_SCK,
+ MX28_PAD_SSP2_SS0__SSP2_D3,
+ MX28_PAD_SSP2_SS1__GPIO_2_20,
+ MX28_PAD_SSP2_SS2__GPIO_2_21,
+
+ /* SPI3 NOR-Flash */
+ MX28_PAD_AUART1_TX__SSP3_CARD_DETECT,
+ MX28_PAD_AUART2_RX__SSP3_D1,
+ MX28_PAD_AUART2_TX__SSP3_D2,
+ MX28_PAD_SSP3_MISO__SSP3_D0,
+ MX28_PAD_SSP3_MOSI__SSP3_CMD,
+ MX28_PAD_SSP3_SCK__SSP3_SCK,
+ MX28_PAD_SSP3_SS0__SSP3_D3,
+
+ /* NOR-Flash CMD */
+ MX28_PAD_LCD_RS__GPIO_1_26, /* Hold */
+ MX28_PAD_LCD_WR_RWN__GPIO_1_25, /* write protect */
+
+ /* I2C0 Codec */
+ MX28_PAD_I2C0_SCL__I2C0_SCL,
+ MX28_PAD_I2C0_SDA__I2C0_SDA,
+
+ /* I2S Codec */
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK,
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK,
+ MX28_PAD_SAIF0_MCLK__SAIF0_MCLK,
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0,
+ MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0,
+
+ /* PWR-Hold */
+ MX28_PAD_SPDIF__GPIO_3_27,
+
+ /* EMI */
+ MX28_PAD_EMI_D00__EMI_DATA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D01__EMI_DATA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D02__EMI_DATA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D03__EMI_DATA3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D04__EMI_DATA4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D05__EMI_DATA5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D06__EMI_DATA6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D07__EMI_DATA7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D08__EMI_DATA8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D09__EMI_DATA9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D10__EMI_DATA10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D11__EMI_DATA11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D12__EMI_DATA12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D13__EMI_DATA13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D14__EMI_DATA14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_D15__EMI_DATA15 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT0__EMI_ODT0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM0__EMI_DQM0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_ODT1__EMI_ODT1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQM1__EMI_DQM1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN_FB__EMI_DDR_OPEN_FEEDBACK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CLK__EMI_CLK | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS0__EMI_DQS0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DQS1__EMI_DQS1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_DDR_OPEN__EMI_DDR_OPEN | MUX_CONFIG_EMI,
+
+ MX28_PAD_EMI_A00__EMI_ADDR0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A01__EMI_ADDR1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A02__EMI_ADDR2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A03__EMI_ADDR3 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A04__EMI_ADDR4 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A05__EMI_ADDR5 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A06__EMI_ADDR6 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A07__EMI_ADDR7 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A08__EMI_ADDR8 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A09__EMI_ADDR9 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A10__EMI_ADDR10 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A11__EMI_ADDR11 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A12__EMI_ADDR12 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A13__EMI_ADDR13 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_A14__EMI_ADDR14 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA0__EMI_BA0 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA1__EMI_BA1 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_BA2__EMI_BA2 | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CASN__EMI_CASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_RASN__EMI_RASN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_WEN__EMI_WEN | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE0N__EMI_CE0N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CE1N__EMI_CE1N | MUX_CONFIG_EMI,
+ MX28_PAD_EMI_CKE__EMI_CKE | MUX_CONFIG_EMI,
+
+ /* Uart3 Bluetooth-Interface */
+ MX28_PAD_AUART3_CTS__AUART3_CTS,
+ MX28_PAD_AUART3_RTS__AUART3_RTS,
+ MX28_PAD_AUART3_RX__AUART3_RX,
+ MX28_PAD_AUART3_TX__AUART3_TX,
+
+ /* framebuffer */
+ MX28_PAD_LCD_CS__LCD_CS | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D00__LCD_D0 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D01__LCD_D1 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D02__LCD_D2 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D03__LCD_D3 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D04__LCD_D4 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D05__LCD_D5 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D06__LCD_D6 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D07__LCD_D7 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D08__LCD_D8 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D09__LCD_D9 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D10__LCD_D10 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D11__LCD_D11 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D12__LCD_D12 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D13__LCD_D13 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D14__LCD_D14 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D15__LCD_D15 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D16__LCD_D16 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D17__LCD_D17 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D18__LCD_D18 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D19__LCD_D19 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D20__LCD_D20 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D21__LCD_D21 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D22__LCD_D22 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_D23__LCD_D23 | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_HSYNC__LCD_HSYNC | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_RD_E__LCD_VSYNC | MUX_CONFIG_LCD,
+ MX28_PAD_LCD_RESET__LCD_RESET | MUX_CONFIG_LCD,
+
+ /* DUART RS232 */
+ MX28_PAD_PWM0__DUART_RX,
+ MX28_PAD_PWM1__DUART_TX,
+
+ /* FEC Ethernet */
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_COL__ENET1_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_MDC__ENET0_MDC | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13, /* Phy Interrupt */
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TX_CLK__GPIO_4_5, /* n.c. */
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1 | MUX_CONFIG_ENET,
+ MX28_PAD_SSP1_CMD__GPIO_2_13, /* PHY reset */
+
+ /* TIVA boot control */
+ MX28_PAD_GPMI_RDY3__GPIO_0_23 | MUX_CONFIG_BOOT, /* TIVA0 */
+ MX28_PAD_GPMI_WRN__GPIO_0_25 | MUX_CONFIG_BOOT, /* TIVA1 */
+};
+
+u32 mxs_dram_vals[] = {
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000100, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00010101, 0x01010101,
+ 0x000f0f01, 0x0f02010a, 0x00000000, 0x00010101,
+ 0x00000100, 0x00000100, 0x00000000, 0x00000002,
+ 0x01010000, 0x07080403, 0x07005303, 0x0b0000c8,
+ 0x0200a0c1, 0x0002040c, 0x0038430a, 0x04290322,
+ 0x02040203, 0x00c8002b, 0x00000000, 0x00000000,
+ 0x00012100, 0xffff0303, 0x00012100, 0xffff0303,
+ 0x00012100, 0xffff0303, 0x00012100, 0xffff0303,
+ 0x00000003, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000612, 0x01000102,
+ 0x06120612, 0x00000200, 0x00020007, 0xf4004a27,
+ 0xf4004a27, 0xf4004a27, 0xf4004a27, 0x07400300,
+ 0x07400300, 0x07400300, 0x07400300, 0x00000005,
+ 0x00000000, 0x00000000, 0x01000000, 0x00000000,
+ 0x00000001, 0x000f1133, 0x00000000, 0x00001f04,
+ 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04,
+ 0x00001f04, 0x00001f04, 0x00001f04, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00010000, 0x00030404,
+ 0x00000002, 0x00000000, 0x00000000, 0x00000000,
+ 0x00000000, 0x00000000, 0x00000000, 0x01010000,
+ 0x01000000, 0x03030000, 0x00010303, 0x01020202,
+ 0x00000000, 0x02040101, 0x21002103, 0x00061200,
+ 0x06120612, 0x00000642, 0x00000000, 0x00000004,
+ 0x00000000, 0x00000080, 0x00000000, 0x00000000,
+ 0x00000000, 0xffffffff
+};
+
+void lowlevel_init(void)
+{
+ struct mxs_pinctrl_regs *pinctrl_regs =
+ (struct mxs_pinctrl_regs *)MXS_PINCTRL_BASE;
+
+ /* Set EMI drive strength */
+ writel(0x00003fff, &pinctrl_regs->hw_pinctrl_emi_ds_ctrl_clr);
+ writel(0x00002aaa, &pinctrl_regs->hw_pinctrl_emi_ds_ctrl_set);
+
+ mxs_common_spl_init(0, NULL, iomux_setup, ARRAY_SIZE(iomux_setup));
+}
diff --git a/board/liebherr/xea/xea.c b/board/liebherr/xea/xea.c
new file mode 100644
index 0000000000..7291313e95
--- /dev/null
+++ b/board/liebherr/xea/xea.c
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * XEA iMX28 board
+ *
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans at mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut at gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ *
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux-mx28.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/sys_proto.h>
+#include <linux/mii.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <errno.h>
+#include <usb.h>
+
+#ifdef CONFIG_SPL_BUILD
+#include <spl.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Functions
+ */
+
+static void init_clocks(void)
+{
+ /* IO0 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK0, 480000);
+ /* IO1 clock at 480MHz */
+ mxs_set_ioclk(MXC_IOCLK1, 480000);
+
+ /* SSP0 clock at 96MHz */
+ mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
+ /* SSP2 clock at 160MHz */
+ mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
+ /* SSP3 clock at 96MHz */
+ mxs_set_sspclk(MXC_SSPCLK3, 96000, 0);
+}
+
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong arg)
+{
+ init_clocks();
+ preloader_console_init();
+}
+
+static int boot_tiva0, boot_tiva1;
+
+/* Check if TIVAs request booting via U-Boot proper */
+void spl_board_init(void)
+{
+ struct gpio_desc btiva0, btiva1;
+ int ret;
+
+ ret = dm_gpio_lookup_name("GPIO0_23", &btiva0);
+ if (ret)
+ printf("Cannot get GPIO0_23\n");
+
+ ret = dm_gpio_lookup_name("GPIO0_25", &btiva1);
+ if (ret)
+ printf("Cannot get GPIO0_25\n");
+
+ ret = dm_gpio_request(&btiva0, "boot-tiva0");
+ if (ret)
+ printf("Cannot request GPIO0_23\n");
+
+ ret = dm_gpio_request(&btiva1, "boot-tiva1");
+ if (ret)
+ printf("Cannot request GPIO0_25\n");
+
+ dm_gpio_set_dir_flags(&btiva0, GPIOD_IS_IN);
+ dm_gpio_set_dir_flags(&btiva1, GPIOD_IS_IN);
+
+ udelay(1000);
+
+ boot_tiva0 = dm_gpio_get_value(&btiva0);
+ boot_tiva1 = dm_gpio_get_value(&btiva1);
+}
+
+void board_boot_order(u32 *spl_boot_list)
+{
+ spl_boot_list[0] = BOOT_DEVICE_MMC1;
+ spl_boot_list[1] = BOOT_DEVICE_SPI;
+}
+
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ if (serial_tstc() && serial_getc() == 'c')
+ return 1;
+
+ debug("%s: btiva0: %d btiva1: %d\n", __func__, boot_tiva0, boot_tiva1);
+ return !boot_tiva0 || !boot_tiva1;
+}
+#else
+
+int board_early_init_f(void)
+{
+ init_clocks();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ struct gpio_desc phy_rst;
+ int ret;
+
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ cpu_eth_init(NULL);
+
+ /* PHY INT#/PWDN# */
+ ret = dm_gpio_lookup_name("GPIO4_13", &phy_rst);
+ if (ret) {
+ printf("Cannot get GPIO4_13\n");
+ return ret;
+ }
+
+ ret = dm_gpio_request(&phy_rst, "phy-rst");
+ if (ret) {
+ printf("Cannot request GPIO4_13\n");
+ return ret;
+ }
+
+ dm_gpio_set_dir_flags(&phy_rst, GPIOD_IS_IN);
+ udelay(1000);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ return mxs_dram_init();
+}
+
+#endif /* CONFIG_SPL_BUILD */
diff --git a/configs/imx28_xea_defconfig b/configs/imx28_xea_defconfig
new file mode 100644
index 0000000000..33ec7a80c5
--- /dev/null
+++ b/configs/imx28_xea_defconfig
@@ -0,0 +1,110 @@
+CONFIG_ARM=y
+CONFIG_SPL_SYS_THUMB_BUILD=y
+CONFIG_ARCH_MX28=y
+CONFIG_SYS_TEXT_BASE=0x40002000
+CONFIG_SPL_GPIO_SUPPORT=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_SYS_MALLOC_F_LEN=0x800
+CONFIG_TARGET_XEA=y
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_SPL_SERIAL_SUPPORT=y
+CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_SPL=y
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+CONFIG_SPL_TEXT_BASE=0x1000
+CONFIG_FIT=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_SPL_BOARD_INIT=y
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0
+CONFIG_SPL_DMA_SUPPORT=y
+CONFIG_SPL_DM_GPIO=y
+CONFIG_SPL_MMC_TINY=y
+CONFIG_SPL_DM_SPI=y
+CONFIG_SPL_DM_SPI_FLASH=y
+CONFIG_SPL_OS_BOOT=y
+CONFIG_SPL_PAYLOAD="u-boot.img"
+CONFIG_SPL_SPI_LOAD=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
+CONFIG_HUSH_PARSER=y
+CONFIG_CMD_SPL=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_GREPENV=y
+CONFIG_CMD_DM=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+# CONFIG_CMD_PINMUX is not set
+CONFIG_CMD_SF=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDIDS_DEFAULT="nor0=spi3.0"
+CONFIG_MTDPARTS_DEFAULT="spi3.0:64k(SPL),448k(uboot),128k(envs),384k(unused1),4096k(kernel),8192k(swupdate),-(unused2)"
+CONFIG_DOS_PARTITION=y
+CONFIG_OF_CONTROL=y
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_DEFAULT_DEVICE_TREE="imx28-xea"
+CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent interrupts"
+CONFIG_SPL_OF_PLATDATA=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=3
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=40000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_DM=y
+CONFIG_SPL_DM=y
+CONFIG_DEVRES=y
+CONFIG_DM_GPIO=y
+CONFIG_MXS_GPIO=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_MMC_MXS=y
+CONFIG_MTD=y
+CONFIG_MTD_DEVICE=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH=y
+CONFIG_SF_DEFAULT_BUS=3
+CONFIG_SF_DEFAULT_MODE=0x0
+CONFIG_SF_DEFAULT_SPEED=40000000
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
+CONFIG_SPI_FLASH_ISSI=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_ADDR_ENABLE=y
+CONFIG_PHY_ADDR=1
+CONFIG_PHY_FIXED=y
+CONFIG_DM_ETH=y
+CONFIG_FEC_MXC=y
+CONFIG_MII=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MXS=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_CONS_INDEX=0
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_MXS_SPI=y
+CONFIG_FS_FAT=y
+# CONFIG_SPL_OF_LIBFDT is not set
+# CONFIG_EFI_LOADER is not set
diff --git a/include/configs/xea.h b/include/configs/xea.h
new file mode 100644
index 0000000000..1edc5e268e
--- /dev/null
+++ b/include/configs/xea.h
@@ -0,0 +1,192 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2019 DENX Software Engineering
+ * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
+ *
+ * Copyright (C) 2018 DENX Software Engineering
+ * Måns Rullgård, DENX Software Engineering, mans at mansr.com
+ *
+ * Copyright (C) 2011 Marek Vasut <marek.vasut at gmail.com>
+ * on behalf of DENX Software Engineering GmbH
+ */
+#ifndef __CONFIGS_XEA_H__
+#define __CONFIGS_XEA_H__
+
+#include <linux/sizes.h>
+
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+/* SPL */
+#define CONFIG_SPL_STACK 0x20000
+
+#define CONFIG_SYS_SPL_ARGS_ADDR 0x44000000
+
+#define CONFIG_SYS_SPI_KERNEL_OFFS SZ_1M
+#define CONFIG_SYS_SPI_ARGS_OFFS SZ_512K
+#define CONFIG_SYS_SPI_ARGS_SIZE SZ_32K
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (SZ_512K / 0x200)
+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (SZ_32K / 0x200)
+#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (SZ_1M / 0x200)
+
+/* Memory configuration */
+#define PHYS_SDRAM_1 0x40000000 /* Base address */
+#define PHYS_SDRAM_1_SIZE 0x10000000 /* Max 256 MB RAM */
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Environment */
+#define CONFIG_ENV_OVERWRITE
+
+/* Booting Linux */
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 "
+#define CONFIG_BOOTCOMMAND "run ${bootpri} ; run ${bootsec}"
+#define CONFIG_LOADADDR 0x42000000
+#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
+
+/* Extra Environment */
+#define CONFIG_PREBOOT "run prebootcmd"
+#define CONFIG_HOSTNAME "xea"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "bootmode=update\0" \
+ "bootpri=mmc_mmc\0" \
+ "bootsec=sf_swu\0" \
+ "consdev=ttyAMA0\0" \
+ "baudrate=115200\0" \
+ "dtbaddr=0x44000000\0" \
+ "dtbfile=imx28-xea.dtb\0" \
+ "rootdev=/dev/mmcblk0p2\0" \
+ "netdev=eth0\0" \
+ "rdaddr=0x43000000\0" \
+ "swufile=swupdate.img\0" \
+ "sf_kernel_offset=0x100000\0" \
+ "sf_kernel_size=0x400000\0" \
+ "sf_swu_offset=0x500000\0" \
+ "sf_swu_size=0x800000\0" \
+ "rootpath=/opt/eldk-5.5/armv5te/rootfs-qte-sdk\0" \
+ "do_update_mmc=" \
+ "if mmc rescan ; then " \
+ "mmc dev 0 ${update_mmc_part} ; " \
+ "if dhcp ${hostname}/${update_filename} ; then " \
+ "setexpr fw_sz ${filesize} / 0x200 ; " /* SD block size */ \
+ "setexpr fw_sz ${fw_sz} + 1 ; " \
+ "mmc write ${loadaddr} ${update_offset} ${fw_sz} ; " \
+ "fi ; " \
+ "fi\0" \
+ "do_update_sf=" \
+ "if sf probe ; then " \
+ "if dhcp ${hostname}/${update_filename} ; then " \
+ "sf erase ${update_offset} +${filesize} ; " \
+ "sf write ${loadaddr} ${update_offset} ${filesize} ; " \
+ "fi ; " \
+ "fi\0" \
+ "update_spl_filename=u-boot.sb\0" \
+ "update_spl=" \
+ "setenv update_filename ${update_spl_filename} ; " \
+ "setenv update_offset 0 ; " \
+ "run do_update_sf\0" \
+ "update_uboot_filename=u-boot.img\0" \
+ "update_uboot=" \
+ "setenv update_filename ${update_uboot_filename} ; " \
+ "setenv update_offset 0x10000 ; " \
+ "run do_update_sf ; " \
+ "setenv update_mmc_part 1 ; " \
+ "setenv update_offset 0 ; " \
+ "run do_update_mmc\0" \
+ "update_kernel_filename=uImage\0" \
+ "update_kernel=" \
+ "setenv update_mmc_part 1 ; " \
+ "setenv update_filename ${update_kernel_filename} ; " \
+ "setenv update_offset 0x800 ; " \
+ "run do_update_mmc ; " \
+ "setenv update_filename ${dtbfile} ; " \
+ "setenv update_offset 0x400 ; " \
+ "run do_update_mmc\0" \
+ "update_sfkernel=" \
+ "setenv update_filename fitImage ; " \
+ "setenv update_offset ${sf_kernel_offset} ; " \
+ "run do_update_sf\0" \
+ "update_swu=" \
+ "setenv update_filename ${swufile} ; " \
+ "setenv update_offset ${sf_swu_offset} ; " \
+ "run do_update_sf\0" \
+ "addcons=" \
+ "setenv bootargs ${bootargs} " \
+ "console=${consdev},${baudrate}\0" \
+ "addip=" \
+ "setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:" \
+ "${netmask}:${hostname}:${netdev}:off\0" \
+ "addmisc=" \
+ "setenv bootargs ${bootargs} ${miscargs}\0" \
+ "addargs=run addcons addmisc\0" \
+ "mmcload=" \
+ "mmc rescan ; " \
+ "mmc dev 0 1 ; " \
+ "mmc read ${loadaddr} 0x800 0x2000 ; " \
+ "mmc read ${dtbaddr} 0x400 0x80\0" \
+ "netload=" \
+ "dhcp ${loadaddr} ${hostname}/${bootfile} ; " \
+ "tftp ${dtbaddr} ${hostname}/${dtbfile}\0" \
+ "sfload=" \
+ "sf probe ; " \
+ "sf read ${loadaddr} ${sf_kernel_offset} ${sf_kernel_size}\0" \
+ "usbload=" \
+ "usb start ; " \
+ "load usb 0:1 ${loadaddr} ${bootfile}\0" \
+ "miscargs=panic=1\0" \
+ "mmcargs=setenv bootargs root=${rootdev} rw rootwait\0" \
+ "nfsargs=" \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath},v3,tcp\0" \
+ "mmc_mmc=" \
+ "if run mmcload mmcargs addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "mmc_nfs=" \
+ "if run mmcload nfsargs addip addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "sf_mmc=" \
+ "if run sfload mmcargs addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "sf_swu=" \
+ "if run sfload ; then " \
+ "sf read ${rdaddr} ${sf_swu_offset} ${sf_swu_size} ; " \
+ "setenv bootargs root=/dev/ram0 rw ; " \
+ "run addargs ; " \
+ "bootm ${loadaddr} ${rdaddr} ; " \
+ "fi\0" \
+ "net_mmc=" \
+ "if run netload mmcargs addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "net_nfs=" \
+ "if run netload nfsargs addip addargs ; then " \
+ "bootm ${loadaddr} - ${dtbaddr} ; " \
+ "fi\0" \
+ "prebootcmd=" \
+ "if test \"${envsaved}\" != y ; then ; " \
+ "setenv envsaved y ; " \
+ "saveenv ; " \
+ "fi ; " \
+ "if test \"${bootmode}\" = normal ; then " \
+ "setenv bootdelay 0 ; " \
+ "setenv bootpri mmc_mmc ; " \
+ "elif test \"${bootmode}\" = devel ; then " \
+ "setenv bootdelay 3 ; " \
+ "setenv bootpri net_mmc ; " \
+ "else " \
+ "if test \"${bootmode}\" != update ; then " \
+ "echo Warning: unknown bootmode \"${bootmode}\" ; " \
+ "fi ; " \
+ "setenv bootdelay 1 ; " \
+ "setenv bootpri sf_swu ; " \
+ "fi\0"
+
+/* The rest of the configuration is shared */
+#include <configs/mxs.h>
+
+#endif /* __CONFIGS_XEA_H__ */
--
2.11.0
More information about the U-Boot
mailing list