[U-Boot] rk3288 (Tinkerboard) not booting【请注意，邮件由u-boot-bounces at lists.denx.de代发】

[Jonathan Gray]

On Mon, Sep 23, 2019 at 01:06:35PM +0000, Alexander von Gluck IV wrote:
> Ok, looking for differences now..
> 
> * Older Tinker Board?  (I'm not using the Tinker Board S)

yes, the original one

> * Same steps?

along the lines of

gmake CROSS_COMPILE="arm-none-eabi-" tinker-rk3288_defconfig
gmake CROSS_COMPILE="arm-none-eabi-" all
tools/mkimage -n rk3288 -T rksd -d tpl/u-boot-tpl.bin idbloader.img && \
    cat spl/u-boot-spl-dtb.bin >> idbloader.img

> * Same config?  tinker-rk3288_defconfig?

yes

> * Uart 115200?

yes

> * Any HDMI Video output?

no hdmi connected only serial

> * GCC version?

gcc-linaro-6.3.2017.02 binutils 2.27 arm-none-eabi target

> 
> September 23, 2019 12:34 AM, "Jonathan Gray" <jsg at jsg.id.au> wrote:
> 
> > On Mon, Sep 23, 2019 at 01:17:40AM +0000, Alexander von Gluck IV wrote:
> > 
> >> Hello!
> >> 
> >> There is no uart output and no video with u-boot master.
> >> The board works as expected booting the Asus Armbian image on an SD.
> >> 
> >> At this point i'd be happy to get some u-boot uart output :-)
> >> 
> >> -- Alex
> > 
> > uart output works here with the latest master
> > (780a17e814503f71d1b51d578b32bc9c89933183)
> > 
> > U-Boot TPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20)
> > Trying to boot from BOOTROM
> > Returning to boot ROM...
> > 
> > U-Boot SPL 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> > Trying to boot from MMC1
> > 
> > U-Boot 2019.10-rc3-00401-ge23a6e5c43 (Sep 23 2019 - 15:13:20 +1000)
> > 
> > Model: Tinker-RK3288
> > DRAM: 2 GiB
> > MMC: dwmmc at ff0c0000: 1
> > Loading Environment from MMC... *** Warning - bad CRC, using default environment
> > 
> > In: serial
> > Out: serial
> > Err: serial
> > Model: Tinker-RK3288
> > rockchip_dnl_key_pressed: adc_channel_single_shot fail!
> > Net: eth0: ethernet at ff290000
> > Hit any key to stop autoboot: 0
> > switch to partitions #0, OK
> > mmc1 is current device
> > Scanning mmc 1:1...
> > Found EFI removable media binary efi/boot/bootarm.efi
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> > Scanning disk dwmmc at ff0c0000.blk...
> > Found 3 disks
> > BootOrder not defined
> > EFI boot manager: Cannot load any image
> > 88176 bytes read in 9 ms (9.3 MiB/s)
> > libfdt fdt_check_header(): FDT_ERR_BADMAGIC
> >>> OpenBSD/armv7 BOOTARM 1.6
> > 
> > boot>
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> https://lists.denx.de/listinfo/u-boot