[PATCH 5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
Patrick DELAUNAY
patrick.delaunay at st.com
Mon Jan 13 15:04:39 CET 2020
Hi Marek,
> From: Marek Vasut <marex at denx.de>
> Sent: vendredi 10 janvier 2020 01:29
> To: u-boot at lists.denx.de
> Cc: Marek Vasut <marex at denx.de>; Patrick DELAUNAY
> <patrick.delaunay at st.com>; Patrice CHOTARD <patrice.chotard at st.com>
> Subject: [PATCH 5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and
> PDK2 board
> Importance: High
>
> Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board.
> This is an SoM with STM32MP157C and an evaluation kit. The baseboard
> provides Ethernet, UART, USB, CAN and optional display.
> Signed-off-by: Marek Vasut <marex at denx.de>
> Cc: Patrick Delaunay <patrick.delaunay at st.com>
> Cc: Patrice Chotard <patrice.chotard at st.com>
> ---
> arch/arm/dts/Makefile | 1 +
> .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts | 7 +
> arch/arm/dts/stm32mp157c-dhcom-pdk2.dts | 88 ++
> arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi | 238 ++++++
> arch/arm/dts/stm32mp157c-dhcom.dtsi | 379 +++++++++
> arch/arm/mach-stm32mp/Kconfig | 1 +
> board/dhelectronics/dh_stm32mp1/Kconfig | 25 +
> board/dhelectronics/dh_stm32mp1/MAINTAINERS | 7 +
> board/dhelectronics/dh_stm32mp1/Makefile | 12 +
> board/dhelectronics/dh_stm32mp1/board.c | 777 ++++++++++++++++++
> configs/stm32mp15_dhcom_basic_defconfig | 140 ++++
> 11 files changed, 1675 insertions(+)
> create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
> create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
> create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
> create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
> create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
> create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> 983e235f44..82489bc09c 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
> dtb-$(CONFIG_TARGET_STM32MP1) += \
> stm32mp157a-dk1.dtb \
> stm32mp157a-avenger96.dtb \
> + stm32mp157c-dhcom-pdk2-u-boot.dtb \
> stm32mp157c-dk2.dtb \
> stm32mp157c-ed1.dtb \
> stm32mp157c-ev1.dtb
> diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> new file mode 100644
> index 0000000000..fd99988570
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> @@ -0,0 +1,7 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */
> +
> +#include "stm32mp157c-dhcom-pdk2.dts"
> +#include "stm32mp157c-dhcom-u-boot.dtsi"
> diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> new file mode 100644
> index 0000000000..05aa545f55
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> @@ -0,0 +1,88 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */
> +
> +#include "stm32mp157c-dhcom.dtsi"
> +
> +/ {
> + model = "STMicroelectronics STM32MP157C DHCOM Premium
> Developer Kit (2)";
> + compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
> +
> + aliases {
> + serial0 = &uart4;
> + ethernet0 = ðernet0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + ethernet_vio: vioregulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vio";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +};
> +
> +ðernet0 {
> + status = "okay";
> + pinctrl-0 = <ðernet0_rmii_pins_a>;
> + pinctrl-1 = <ðernet0_rmii_pins_sleep_a>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rmii";
> + max-speed = <100>;
> + phy-handle = <&phy0>;
> + st,eth_ref_clk_sel;
> + phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> +
> + phy0: ethernet-phy at 1 {
> + reg = <1>;
> + };
> + };
> +};
> +
> +&pinctrl {
> + ethernet0_rmii_pins_a: rmii-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('G', 13, AF11)>, /*
> ETH1_RMII_TXD0 */
> + <STM32_PINMUX('G', 14, AF11)>, /*
> ETH1_RMII_TXD1 */
> + <STM32_PINMUX('B', 11, AF11)>, /*
> ETH1_RMII_TX_EN */
> + <STM32_PINMUX('A', 1, AF0)>, /*
> ETH1_RMII_REF_CLK */
> + <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO
> */
> + <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC
> */
> + bias-disable;
> + drive-push-pull;
> + slew-rate = <2>;
> + };
> + pins2 {
> + pinmux = <STM32_PINMUX('C', 4, AF11)>, /*
> ETH1_RMII_RXD0 */
> + <STM32_PINMUX('C', 5, AF11)>, /*
> ETH1_RMII_RXD1 */
> + <STM32_PINMUX('A', 7, AF11)>; /*
> ETH1_RMII_CRS_DV */
> + bias-disable;
> + };
> + };
> +
> + ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
> + pins1 {
> + pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*
> ETH1_RMII_TXD0 */
> + <STM32_PINMUX('G', 14, ANALOG)>, /*
> ETH1_RMII_TXD1 */
> + <STM32_PINMUX('B', 11, ANALOG)>, /*
> ETH1_RMII_TX_EN */
> + <STM32_PINMUX('A', 2, ANALOG)>, /*
> ETH1_MDIO */
> + <STM32_PINMUX('C', 1, ANALOG)>, /*
> ETH1_MDC */
> + <STM32_PINMUX('C', 4, ANALOG)>, /*
> ETH1_RMII_RXD0 */
> + <STM32_PINMUX('C', 5, ANALOG)>, /*
> ETH1_RMII_RXD1 */
> + <STM32_PINMUX('A', 1, ANALOG)>, /*
> ETH1_RMII_REF_CLK */
> + <STM32_PINMUX('A', 7, ANALOG)>; /*
> ETH1_RMII_CRS_DV */
> + };
> + };
> +};
> diff --git a/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> new file mode 100644
> index 0000000000..320912edd8
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> @@ -0,0 +1,238 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */
> +
> +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> +#include "stm32mp157-u-boot.dtsi"
> +#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
> +
> +/ {
> + aliases {
> + i2c1 = &i2c2;
> + i2c3 = &i2c4;
> + i2c4 = &i2c5;
> + mmc0 = &sdmmc1;
> + mmc1 = &sdmmc2;
> + spi0 = &qspi;
> + usb0 = &usbotg_hs;
> + };
> +
> + config {
> + u-boot,boot-led = "heartbeat";
> + u-boot,error-led = "error";
Excpet if I miss something, You have no led on your board (named = "heartbeat" or "error" )
This 2 line can be remove I think
> + st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> + st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + led {
> + red {
> + label = "error";
> + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> + default-state = "off";
> + status = "okay";
> + };
> +
> + blue {
> + default-state = "on";
> + };
> + };
This blue overridde can be remove I think.
> +};
> +
> +&i2c4 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&i2c4_pins_a {
> + u-boot,dm-pre-reloc;
> + pins {
> + u-boot,dm-pre-reloc;
> + };
> +};
> +
> +&pmic {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&flash0 {
> + u-boot,dm-spl;
> +};
> +
> +&qspi {
> + u-boot,dm-spl;
> +};
> +
> +&qspi_clk_pins_a {
> + u-boot,dm-spl;
> + pins {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&qspi_bk1_pins_a {
> + u-boot,dm-spl;
> + pins1 {
> + u-boot,dm-spl;
> + };
> + pins2 {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&qspi_bk2_pins_a {
> + u-boot,dm-spl;
> + pins1 {
> + u-boot,dm-spl;
> + };
> + pins2 {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&rcc {
> + st,clksrc = <
> + CLK_MPU_PLL1P
> + CLK_AXI_PLL2P
> + CLK_MCU_PLL3P
> + CLK_PLL12_HSE
> + CLK_PLL3_HSE
> + CLK_PLL4_HSE
> + CLK_RTC_LSE
> + CLK_MCO1_DISABLED
> + CLK_MCO2_DISABLED
> + >;
> +
> + st,clkdiv = <
> + 1 /*MPU*/
> + 0 /*AXI*/
> + 0 /*MCU*/
> + 1 /*APB1*/
> + 1 /*APB2*/
> + 1 /*APB3*/
> + 1 /*APB4*/
> + 2 /*APB5*/
> + 23 /*RTC*/
> + 0 /*MCO1*/
> + 0 /*MCO2*/
> + >;
> +
> + st,pkcs = <
> + CLK_CKPER_HSE
> + CLK_FMC_ACLK
> + CLK_QSPI_ACLK
> + CLK_ETH_PLL4P
> + CLK_SDMMC12_PLL4P
> + CLK_DSI_DSIPLL
> + CLK_STGEN_HSE
> + CLK_USBPHY_HSE
> + CLK_SPI2S1_PLL3Q
> + CLK_SPI2S23_PLL3Q
> + CLK_SPI45_HSI
> + CLK_SPI6_HSI
> + CLK_I2C46_HSI
> + CLK_SDMMC3_PLL4P
> + CLK_USBO_USBPHY
> + CLK_ADC_CKPER
> + CLK_CEC_LSE
> + CLK_I2C12_HSI
> + CLK_I2C35_HSI
> + CLK_UART1_HSI
> + CLK_UART24_HSI
> + CLK_UART35_HSI
> + CLK_UART6_HSI
> + CLK_UART78_HSI
> + CLK_SPDIF_PLL4P
> + CLK_FDCAN_PLL4Q
> + CLK_SAI1_PLL3Q
> + CLK_SAI2_PLL3Q
> + CLK_SAI3_PLL3Q
> + CLK_SAI4_PLL3Q
> + CLK_RNG1_LSI
> + CLK_RNG2_LSI
> + CLK_LPTIM1_PCLK1
> + CLK_LPTIM23_PCLK3
> + CLK_LPTIM45_LSE
> + >;
> +
> + /* VCO = 1300.0 MHz => P = 650 (CPU) */
> + pll1: st,pll at 0 {
> + cfg = < 2 80 0 0 0 PQR(1,0,0) >;
> + frac = < 0x800 >;
> + u-boot,dm-pre-reloc;
> + };
> +
> + /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
> + pll2: st,pll at 1 {
> + cfg = < 2 65 1 0 0 PQR(1,1,1) >;
> + frac = < 0x1400 >;
> + u-boot,dm-pre-reloc;
> + };
> +
> + /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
> + pll3: st,pll at 2 {
> + cfg = < 1 33 1 16 36 PQR(1,1,1) >;
> + frac = < 0x1a04 >;
> + u-boot,dm-pre-reloc;
> + };
> +
> + /* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
> + pll4: st,pll at 3 {
> + cfg = < 1 49 11 11 11 PQR(1,1,1) >;
> + u-boot,dm-pre-reloc;
> + };
> +};
> +
> +&sdmmc1 {
> + u-boot,dm-spl;
> +};
> +
> +&sdmmc1_b4_pins_a {
> + u-boot,dm-spl;
> + pins {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&sdmmc1_dir_pins_a {
> + u-boot,dm-spl;
> + pins1 {
> + u-boot,dm-spl;
> + };
> + pins2 {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&sdmmc2 {
> + u-boot,dm-spl;
> +};
> +
> +&sdmmc2_b4_pins_a {
> + u-boot,dm-spl;
> + pins {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&sdmmc2_d47_pins_a {
> + u-boot,dm-spl;
> + pins {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&uart4 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_a {
> + u-boot,dm-pre-reloc;
> + pins1 {
> + u-boot,dm-pre-reloc;
> + };
> + pins2 {
> + u-boot,dm-pre-reloc;
> + /* pull-up on rx to avoid floating level */
> + bias-pull-up;
> + };
> +};
> diff --git a/arch/arm/dts/stm32mp157c-dhcom.dtsi b/arch/arm/dts/stm32mp157c-
> dhcom.dtsi
> new file mode 100644
> index 0000000000..96661ae783
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom.dtsi
> @@ -0,0 +1,379 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */ /dts-v1/;
> +
> +#include "stm32mp157c.dtsi"
> +#include "stm32mp157xaa-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> + memory at c0000000 {
> + device_type = "memory";
> + reg = <0xC0000000 0x40000000>;
> + };
> +};
> +
> +&cec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&cec_pins_a>;
> + status = "okay";
> +};
> +
> +&dcmi {
> + status = "okay";
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&dcmi_pins_a>;
> + pinctrl-1 = <&dcmi_sleep_pins_a>;
> +};
> +
> +&dts {
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /* spare dmas for other usage */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +
> + pmic: stpmic at 33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "okay";
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> + ldo1-supply = <&v3v3>;
> + ldo2-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo5-supply = <&v3v3>;
> + ldo6-supply = <&v3v3>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + st,mask-reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + vdda: ldo1 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO1 0>;
> + };
> +
> + v2v8: ldo2 {
> + regulator-name = "v2v8";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + interrupts = <IT_CURLIM_LDO2 0>;
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <750000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + interrupts = <IT_CURLIM_LDO4 0>;
> + };
> +
> + vdd_sd: ldo5 {
> + regulator-name = "vdd_sd";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + regulator-boot-on;
> + };
> +
> + v1v8: ldo6 {
> + regulator-name = "v1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + interrupts = <IT_CURLIM_LDO6 0>;
> + };
> +
> + vref_ddr: vref_ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + regulator-active-discharge;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + power-off-time-sec = <10>;
> + status = "okay";
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + status = "disabled";
> + };
> + };
> +
> + eeprom at 50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + pagesize = <16>;
> + };
> +};
> +
> +&i2c5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c5_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> +};
> +
> +&ipcc {
> + status = "okay";
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&m4_rproc {
> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> + mbox-names = "vq0", "vq1", "shutdown";
> + status = "okay";
> +};
> +
> +&pwr {
> + pwr-regulators {
> + vdd-supply = <&vdd>;
> + vdd_3v3_usbfs-supply = <&vdd_usb>;
> + };
> +};
> +
> +&qspi {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
> + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a
> &qspi_bk2_sleep_pins_a>;
> + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + flash0: mx66l51235l at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <108000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +
> + flash1: mx66l51235l at 1 {
> + compatible = "jedec,spi-nor";
> + reg = <1>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <108000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
> + broken-cd;
> + st,sig-dir;
> + st,neg-edge;
> + st,use-ckin;
> + bus-width = <4>;
> + vmmc-supply = <&vdd_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,sig-dir;
> + st,neg-edge;
> + bus-width = <8>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_pins_a>;
> + status = "disabled";
> +};
> +
> +&timers2 {
> + /* spare dmas for other usage (un-delete to enable pwm capture) */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + status = "disabled";
> + pwm {
> + pinctrl-0 = <&pwm2_pins_a>;
> + pinctrl-names = "default";
> + status = "okay";
> + };
> + timer at 1 {
> + status = "okay";
> + };
> +};
> +
> +&timers6 {
> + status = "okay";
> + /* spare dmas for other usage */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + timer at 5 {
> + status = "okay";
> + };
> +};
> +
> +&timers8 {
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + status = "disabled";
> + pwm {
> + pinctrl-0 = <&pwm8_pins_a>;
> + pinctrl-names = "default";
> + status = "okay";
> + };
> + timer at 7 {
> + status = "okay";
> + };
> +};
> +
> +&timers12 {
> + /delete-property/dmas;
> + /delete-property/dma-names;
> + status = "disabled";
> + pwm {
> + pinctrl-0 = <&pwm12_pins_a>;
> + pinctrl-names = "default";
> + status = "okay";
> + };
> + timer at 11 {
> + status = "okay";
> + };
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins_a>;
> + status = "okay";
> +};
> +
> +&usbh_ehci {
> + phys = <&usbphyc_port0>;
> + phy-names = "usb";
> + status = "okay";
> +};
> +
> +&usbotg_hs {
> + dr_mode = "peripheral";
> + phys = <&usbphyc_port1 0>;
> + phy-names = "usb2-phy";
> + vbus-supply = <&vbus_otg>;
> + status = "okay";
> +};
> +
> +&usbphyc {
> + status = "okay";
> +};
> +
> +&usbphyc_port0 {
> + phy-supply = <&vdd_usb>;
> +};
> +
> +&usbphyc_port1 {
> + phy-supply = <&vdd_usb>;
> +};
> diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
> index ae28f6e206..1aa5f8a122 100644
> --- a/arch/arm/mach-stm32mp/Kconfig
> +++ b/arch/arm/mach-stm32mp/Kconfig
> @@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK endif
>
> source "board/st/stm32mp1/Kconfig"
> +source "board/dhelectronics/dh_stm32mp1/Kconfig"
>
> endif
> diff --git a/board/dhelectronics/dh_stm32mp1/Kconfig
> b/board/dhelectronics/dh_stm32mp1/Kconfig
> new file mode 100644
> index 0000000000..e751a3e5ed
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/Kconfig
> @@ -0,0 +1,25 @@
> +config TARGET_DH_STM32MP1_PDK2
> + bool "support of DH STM32MP1 PDK2"
> + default y
Avoid set default y here....
to avoid to activate this config for ST board.
In fact it should be a choice between the 2 targets
- TARGET_DH_STM32MP1_PDK2
- TARGET_ST_STM32MP1
> +
> +if TARGET_DH_STM32MP1_PDK2
> +
> +config SYS_BOARD
> + default "dh_stm32mp1"
> +
> +config SYS_VENDOR
> + default "dhelectronics"
> +
> +config SYS_CONFIG_NAME
> + default "stm32mp1"
> +
> +config ENV_SECT_SIZE
> + default 0x10000 if ENV_IS_IN_SPI_FLASH
> +
> +config ENV_OFFSET
> + default 0x1E0000 if ENV_IS_IN_SPI_FLASH
> +
> +config ENV_OFFSET_REDUND
> + default 0x1F0000 if ENV_IS_IN_SPI_FLASH
> +
> +endif
> diff --git a/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> new file mode 100644
> index 0000000000..38f54a3da4
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> @@ -0,0 +1,7 @@
> +DH_STM32MP1_PDK2 BOARD
> +M: Marek Vasut <marex at denx.de>
> +S: Maintained
> +F: arch/arm/dts/stm32mp157c-dhcom*
> +F: board/dhelectronics/dh_stm32mp1/
> +F: configs/stm32mp15_dhcom_basic_defconfig
> +F: include/configs/stm32mp1.h
> diff --git a/board/dhelectronics/dh_stm32mp1/Makefile
> b/board/dhelectronics/dh_stm32mp1/Makefile
> new file mode 100644
> index 0000000000..a9d28218ef
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/Makefile
> @@ -0,0 +1,12 @@
> +# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
> +2018, STMicroelectronics - All Rights Reserved #
> +
> +ifdef CONFIG_SPL_BUILD
> +obj-y += ../../st/stm32mp1/spl.o
> +else
> +obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif
> +
I don't think you wee to support the command STMicroelctronics board (ref MBxxxx).
it is only a internal command for ST : save/read board id in OTP.
> +obj-y += ../../st/stm32mp1/board.o board.o
> diff --git a/board/dhelectronics/dh_stm32mp1/board.c
> b/board/dhelectronics/dh_stm32mp1/board.c
> new file mode 100644
> index 0000000000..54cc3b7587
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/board.c
> @@ -0,0 +1,777 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved */
> +
> +#include <common.h>
> +#include <adc.h>
> +#include <asm/arch/stm32.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/gpio.h>
> +#include <asm/io.h>
> +#include <bootm.h>
> +#include <clk.h>
> +#include <config.h>
> +#include <dm.h>
> +#include <dm/device.h>
> +#include <dm/uclass.h>
> +#include <env.h>
> +#include <env_internal.h>
> +#include <g_dnl.h>
> +#include <generic-phy.h>
> +#include <i2c.h>
> +#include <i2c_eeprom.h>
> +#include <init.h>
> +#include <led.h>
> +#include <memalign.h>
> +#include <misc.h>
> +#include <mtd.h>
> +#include <mtd_node.h>
> +#include <netdev.h>
> +#include <phy.h>
> +#include <power/regulator.h>
> +#include <remoteproc.h>
> +#include <reset.h>
> +#include <syscon.h>
> +#include <usb.h>
> +#include <usb/dwc2_udc.h>
> +#include <watchdog.h>
> +
> +/* SYSCFG registers */
> +#define SYSCFG_BOOTR 0x00
> +#define SYSCFG_PMCSETR 0x04
> +#define SYSCFG_IOCTRLSETR 0x18
> +#define SYSCFG_ICNR 0x1C
> +#define SYSCFG_CMPCR 0x20
> +#define SYSCFG_CMPENSETR 0x24
> +#define SYSCFG_PMCCLRR 0x44
> +
> +#define SYSCFG_BOOTR_BOOT_MASK GENMASK(2, 0)
> +#define SYSCFG_BOOTR_BOOTPD_SHIFT 4
> +
> +#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE BIT(0)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI BIT(1)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_ETH BIT(2)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC BIT(3)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_SPI BIT(4)
> +
> +#define SYSCFG_CMPCR_SW_CTRL BIT(1)
> +#define SYSCFG_CMPCR_READY BIT(8)
> +
> +#define SYSCFG_CMPENSETR_MPU_EN BIT(0)
> +
> +#define SYSCFG_PMCSETR_ETH_CLK_SEL BIT(16)
> +#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL BIT(17)
> +
> +#define SYSCFG_PMCSETR_ETH_SELMII BIT(20)
> +
> +#define SYSCFG_PMCSETR_ETH_SEL_MASK GENMASK(23, 21)
> +#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII 0
> +#define SYSCFG_PMCSETR_ETH_SEL_RGMII BIT(21)
> +#define SYSCFG_PMCSETR_ETH_SEL_RMII BIT(23)
> +
> +/*
> + * Get a global data pointer
> + */
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int setup_mac_address(void)
> +{
> + struct udevice *dev;
> + ofnode eeprom;
> + unsigned char enetaddr[6];
> + int ret;
> +
> + ret = eth_env_get_enetaddr("ethaddr", enetaddr);
> + if (ret) /* ethaddr is already set */
> + return 0;
> +
> + eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
> + if (!ofnode_valid(eeprom)) {
> + printf("Invalid hardware path to EEPROM!\n");
> + return -ENODEV;
> + }
> +
> + ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,
> &dev);
> + if (ret) {
> + printf("Cannot find EEPROM!\n");
> + return ret;
> + }
> +
> + ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
> + if (ret) {
> + printf("Error reading configuration EEPROM!\n");
> + return ret;
> + }
> +
> + if (is_valid_ethaddr(enetaddr))
> + eth_env_set_enetaddr("ethaddr", enetaddr);
> +
> + return 0;
> +}
> +
> +int checkboard(void)
> +{
> + int ret;
> + char *mode;
> + u32 otp;
> + struct udevice *dev;
> + const char *fdt_compat;
> + int fdt_compat_len;
> +
> + if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
> + mode = "trusted with OP-TEE";
> + else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
> + mode = "trusted";
> + else
> + mode = "basic";
> +
> + printf("Board: stm32mp1 in %s mode", mode);
> + fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> + &fdt_compat_len);
> + if (fdt_compat && fdt_compat_len)
> + printf(" (%s)", fdt_compat);
> + puts("\n");
> +
> + ret = uclass_get_device_by_driver(UCLASS_MISC,
> + DM_GET_DRIVER(stm32mp_bsec),
> + &dev);
> +
> + if (!ret)
> + ret = misc_read(dev,
> STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> + &otp, sizeof(otp));
> + if (ret > 0 && otp) {
> + printf("Board: MB%04x Var%d Rev.%c-%02d\n",
> + otp >> 16,
> + (otp >> 12) & 0xF,
> + ((otp >> 8) & 0xF) - 1 + 'A',
> + otp & 0xF);
> + }
This part (read OTP / / display MBxxx ) can be dropped for your board (it is a ST specific part).
> + return 0;
> +}
> +
> +static void board_key_check(void)
> +{
> +#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
> + ofnode node;
> + struct gpio_desc gpio;
> + enum forced_boot_mode boot_mode = BOOT_NORMAL;
> +
> + node = ofnode_path("/config");
> + if (!ofnode_valid(node)) {
> + debug("%s: no /config node?\n", __func__);
> + return;
> + }
> +#ifdef CONFIG_FASTBOOT
> + if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
> + &gpio, GPIOD_IS_IN)) {
> + debug("%s: could not find a /config/st,fastboot-gpios\n",
> + __func__);
> + } else {
> + if (dm_gpio_get_value(&gpio)) {
> + puts("Fastboot key pressed, ");
> + boot_mode = BOOT_FASTBOOT;
> + }
> +
> + dm_gpio_free(NULL, &gpio);
> + }
> +#endif
> +#ifdef CONFIG_CMD_STM32PROG
> + if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
> + &gpio, GPIOD_IS_IN)) {
> + debug("%s: could not find a /config/st,stm32prog-gpios\n",
> + __func__);
> + } else {
> + if (dm_gpio_get_value(&gpio)) {
> + puts("STM32Programmer key pressed, ");
> + boot_mode = BOOT_STM32PROG;
> + }
> + dm_gpio_free(NULL, &gpio);
> + }
> +#endif
> +
> + if (boot_mode != BOOT_NORMAL) {
> + puts("entering download mode...\n");
> + clrsetbits_le32(TAMP_BOOT_CONTEXT,
> + TAMP_BOOT_FORCED_MASK,
> + boot_mode);
> + }
> +#endif
> +}
Do you support GPIO key press on GPAIOA14 / 15 (as it is done in ST boards EV1 : DK1 / DK2)
If no all this function can be dropped.
> +#if defined(CONFIG_USB_GADGET) &&
> defined(CONFIG_USB_GADGET_DWC2_OTG)
> +
> +/* STMicroelectronics STUSB1600 Type-C controller */
> +#define STUSB1600_CC_CONNECTION_STATUS 0x0E
> +
> +/* STUSB1600_CC_CONNECTION_STATUS bitfields */
> +#define STUSB1600_CC_ATTACH BIT(0)
> +
> +static int stusb1600_init(struct udevice **dev_stusb1600) {
> + ofnode node;
> + struct udevice *dev, *bus;
> + int ret;
> + u32 chip_addr;
> +
> + *dev_stusb1600 = NULL;
> +
> + /* if node stusb1600 is present, means DK1 or DK2 board */
> + node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
> + if (!ofnode_valid(node))
> + return -ENODEV;
> +
> + ret = ofnode_read_u32(node, "reg", &chip_addr);
> + if (ret)
> + return -EINVAL;
> +
> + ret = uclass_get_device_by_ofnode(UCLASS_I2C,
> ofnode_get_parent(node),
> + &bus);
> + if (ret) {
> + printf("bus for stusb1600 not found\n");
> + return -ENODEV;
> + }
> +
> + ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
> + if (!ret)
> + *dev_stusb1600 = dev;
> +
> + return ret;
> +}
> +
> +static int stusb1600_cable_connected(struct udevice *dev) {
> + u8 status;
> +
> + if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,
> 1))
> + return 0;
> +
> + return status & STUSB1600_CC_ATTACH;
> +}
> +
> +#include <usb/dwc2_udc.h>
> +int g_dnl_board_usb_cable_connected(void)
> +{
> + struct udevice *stusb1600;
> + struct udevice *dwc2_udc_otg;
> + int ret;
> +
> + if (!stusb1600_init(&stusb1600))
> + return stusb1600_cable_connected(stusb1600);
> +
> + ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
> + DM_GET_DRIVER(dwc2_udc_otg),
> + &dwc2_udc_otg);
> + if (!ret)
> + debug("dwc2_udc_otg init failed\n");
> +
> + return dwc2_udc_B_session_valid(dwc2_udc_otg);
> +}
> +
If you don't have STUSB1600 (external usb typeC controller)
All this part can dropped.
> +#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
> +STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
> +
> +int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
> +*name) {
> + if (!strcmp(name, "usb_dnl_dfu"))
> + put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
> >idProduct);
> + else if (!strcmp(name, "usb_dnl_fastboot"))
> +
> put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,
> + &dev->idProduct);
> + else
> + put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
> >idProduct);
> +
> + return 0;
> +}
> +
> +#endif /* CONFIG_USB_GADGET */
> +
> +#ifdef CONFIG_LED
> +static int get_led(struct udevice **dev, char *led_string) {
> + char *led_name;
> + int ret;
> +
> + led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
> + if (!led_name) {
> + pr_debug("%s: could not find %s config string\n",
> + __func__, led_string);
> + return -ENOENT;
> + }
> + ret = led_get_by_label(led_name, dev);
> + if (ret) {
> + debug("%s: get=%d\n", __func__, ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int setup_led(enum led_state_t cmd) {
> + struct udevice *dev;
> + int ret;
> +
> + ret = get_led(&dev, "u-boot,boot-led");
> + if (ret)
> + return ret;
> +
> + ret = led_set_state(dev, cmd);
> + return ret;
> +}
> +#endif
> +
> +static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
> +CONFIG_LED
> + int ret;
> + struct udevice *led;
> + u32 i;
> +#endif
> +
> + if (!nb_blink)
> + return;
> +
> +#ifdef CONFIG_LED
> + ret = get_led(&led, "u-boot,error-led");
> + if (!ret) {
> + /* make u-boot,error-led blinking */
> + /* if U32_MAX and 125ms interval, for 17.02 years */
> + for (i = 0; i < 2 * nb_blink; i++) {
> + led_set_state(led, LEDST_TOGGLE);
> + mdelay(125);
> + WATCHDOG_RESET();
> + }
> + }
> +#endif
> +
> + /* infinite: the boot process must be stopped */
> + if (nb_blink == U32_MAX)
> + hang();
> +}
> +
> +static void sysconf_init(void)
> +{
> +#ifndef CONFIG_STM32MP1_TRUSTED
> + u8 *syscfg;
> +#ifdef CONFIG_DM_REGULATOR
> + struct udevice *pwr_dev;
> + struct udevice *pwr_reg;
> + struct udevice *dev;
> + int ret;
> + u32 otp = 0;
> +#endif
> + u32 bootr;
> +
> + syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> +
> + /* interconnect update : select master using the port 1 */
> + /* LTDC = AXI_M9 */
> + /* GPU = AXI_M8 */
> + /* today information is hardcoded in U-Boot */
> + writel(BIT(9), syscfg + SYSCFG_ICNR);
> +
> + /* disable Pull-Down for boot pin connected to VDD */
> + bootr = readl(syscfg + SYSCFG_BOOTR);
> + bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<
> SYSCFG_BOOTR_BOOTPD_SHIFT);
> + bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<
> SYSCFG_BOOTR_BOOTPD_SHIFT;
> + writel(bootr, syscfg + SYSCFG_BOOTR);
> +
> +#ifdef CONFIG_DM_REGULATOR
> + /* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,
> QSPI
> + * and TRACE. Needed above ~50MHz and conditioned by AFMUX
> selection.
> + * The customer will have to disable this for low frequencies
> + * or if AFMUX is selected but the function not used, typically for
> + * TRACE. Otherwise, impact on power consumption.
> + *
> + * WARNING:
> + * enabling High Speed mode while VDD>2.7V
> + * with the OTP product_below_2v5 (OTP 18, BIT 13)
> + * erroneously set to 1 can damage the IC!
> + * => U-Boot set the register only if VDD < 2.7V (in DT)
> + * but this value need to be consistent with board design
> + */
> + ret = uclass_get_device_by_driver(UCLASS_PMIC,
> + DM_GET_DRIVER(stm32mp_pwr_pmic),
> + &pwr_dev);
> + if (!ret) {
> + ret = uclass_get_device_by_driver(UCLASS_MISC,
> +
> DM_GET_DRIVER(stm32mp_bsec),
> + &dev);
> + if (ret) {
> + pr_err("Can't find stm32mp_bsec driver\n");
> + return;
> + }
> +
> + ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
> + if (ret > 0)
> + otp = otp & BIT(13);
> +
> + /* get VDD = vdd-supply */
> + ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
> + &pwr_reg);
> +
> + /* check if VDD is Low Voltage */
> + if (!ret) {
> + if (regulator_get_value(pwr_reg) < 2700000) {
> + writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
> + SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI
> |
> + SYSCFG_IOCTRLSETR_HSLVEN_ETH |
> + SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
> + SYSCFG_IOCTRLSETR_HSLVEN_SPI,
> + syscfg + SYSCFG_IOCTRLSETR);
> +
> + if (!otp)
> + pr_err("product_below_2v5=0: HSLVEN
> protected by HW\n");
> + } else {
> + if (otp)
> + pr_err("product_below_2v5=1: HSLVEN
> update is destructive, no update as VDD>2.7V\n");
> + }
> + } else {
> + debug("VDD unknown");
> + }
> + }
> +#endif
> +
> + /* activate automatic I/O compensation
> + * warning: need to ensure CSI enabled and ready in clock driver
> + */
> + writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +
> SYSCFG_CMPENSETR);
> +
> + while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
> + ;
> + clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
> #endif }
> +
> +/* board dependent setup after realloc */ int board_init(void) {
> + struct udevice *dev;
> +
> + /* address of boot parameters */
> + gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
> +
> + /* probe all PINCTRL for hog */
> + for (uclass_first_device(UCLASS_PINCTRL, &dev);
> + dev;
> + uclass_next_device(&dev)) {
> + pr_debug("probe pincontrol = %s\n", dev->name);
> + }
> +
> + board_key_check();
> +
> +#ifdef CONFIG_DM_REGULATOR
> + regulators_enable_boot_on(_DEBUG);
> +#endif
> +
> + sysconf_init();
> +
> + if (CONFIG_IS_ENABLED(CONFIG_LED))
> + led_default_state();
> +
> + return 0;
> +}
> +
> +int board_late_init(void)
> +{
> + char *boot_device;
> +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> + const void *fdt_compat;
> + int fdt_compat_len;
> + int ret;
> + u32 otp;
> + struct udevice *dev;
> + char buf[10];
> +
> + fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> + &fdt_compat_len);
> + if (fdt_compat && fdt_compat_len) {
> + if (strncmp(fdt_compat, "st,", 3) != 0)
> + env_set("board_name", fdt_compat);
> + else
> + env_set("board_name", fdt_compat + 3);
> + }
> + ret = uclass_get_device_by_driver(UCLASS_MISC,
> + DM_GET_DRIVER(stm32mp_bsec),
> + &dev);
> +
> + if (!ret)
> + ret = misc_read(dev,
> STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> + &otp, sizeof(otp));
> + if (!ret && otp) {
> + snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
> + env_set("board_id", buf);
> +
> + snprintf(buf, sizeof(buf), "0x%04x",
> + ((otp >> 8) & 0xF) - 1 + 0xA);
> + env_set("board_rev", buf);
> + }
> +#endif
> +
> + /* Check the boot-source to disable bootdelay */
> + boot_device = env_get("boot_device");
> + if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
> + env_set("bootdelay", "0");
> +
> + return 0;
> +}
> +
> +void board_quiesce_devices(void)
> +{
> +#ifdef CONFIG_LED
> + setup_led(LEDST_OFF);
> +#endif
> +}
> +
> +/* eth init function : weak called in eqos driver */ int
> +board_interface_eth_init(struct udevice *dev,
> + phy_interface_t interface_type) {
> + u8 *syscfg;
> + u32 value;
> + bool eth_clk_sel_reg = false;
> + bool eth_ref_clk_sel_reg = false;
> +
> + /* Gigabit Ethernet 125MHz clock selection. */
> + eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
> +
> + /* Ethernet 50Mhz RMII clock selection */
> + eth_ref_clk_sel_reg =
> + dev_read_bool(dev, "st,eth_ref_clk_sel");
> +
> + syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> +
> + if (!syscfg)
> + return -ENODEV;
> +
> + switch (interface_type) {
> + case PHY_INTERFACE_MODE_MII:
> + value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> + SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> + debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
> + break;
> + case PHY_INTERFACE_MODE_GMII:
> + if (eth_clk_sel_reg)
> + value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> + SYSCFG_PMCSETR_ETH_CLK_SEL;
> + else
> + value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
> + debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
> + break;
> + case PHY_INTERFACE_MODE_RMII:
> + if (eth_ref_clk_sel_reg)
> + value = SYSCFG_PMCSETR_ETH_SEL_RMII |
> + SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> + else
> + value = SYSCFG_PMCSETR_ETH_SEL_RMII;
> + debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
> + break;
> + case PHY_INTERFACE_MODE_RGMII:
> + case PHY_INTERFACE_MODE_RGMII_ID:
> + case PHY_INTERFACE_MODE_RGMII_RXID:
> + case PHY_INTERFACE_MODE_RGMII_TXID:
> + if (eth_clk_sel_reg)
> + value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
> + SYSCFG_PMCSETR_ETH_CLK_SEL;
> + else
> + value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
> + debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
> + break;
> + default:
> + debug("%s: Do not manage %d interface\n",
> + __func__, interface_type);
> + /* Do not manage others interfaces */
> + return -EINVAL;
> + }
> +
> + /* clear and set ETH configuration bits */
> + writel(SYSCFG_PMCSETR_ETH_SEL_MASK |
> SYSCFG_PMCSETR_ETH_SELMII |
> + SYSCFG_PMCSETR_ETH_REF_CLK_SEL |
> SYSCFG_PMCSETR_ETH_CLK_SEL,
> + syscfg + SYSCFG_PMCCLRR);
> + writel(value, syscfg + SYSCFG_PMCSETR);
> +
> + return 0;
> +}
> +
> +enum env_location env_get_location(enum env_operation op, int prio) {
> + if (prio)
> + return ENVL_UNKNOWN;
> +
> +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
> + return ENVL_SPI_FLASH;
> +#else
> + return ENVL_NOWHERE;
> +#endif
> +}
> +
> +#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
> +
> +#define MTDPARTS_LEN 256
> +#define MTDIDS_LEN 128
> +
> +/**
> + * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
> + * If we need to access it before the env is relocated, then we need
> + * to use our own stack buffer. gd->env_buf will be too small.
> + *
> + * @param buf temporary buffer pointer MTDPARTS_LEN long
> + * @return mtdparts variable string, NULL if not found */ static const
> +char *env_get_mtdparts(const char *str, char *buf) {
> + if (gd->flags & GD_FLG_ENV_READY)
> + return env_get(str);
> + if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
> + return buf;
> +
> + return NULL;
> +}
> +
> +/**
> + * update the variables "mtdids" and "mtdparts" with content of
> +mtdparts_<dev> */ static void board_get_mtdparts(const char *dev,
> + char *mtdids,
> + char *mtdparts)
> +{
> + char env_name[32] = "mtdparts_";
> + char tmp_mtdparts[MTDPARTS_LEN];
> + const char *tmp;
> +
> + /* name of env variable to read = mtdparts_<dev> */
> + strcat(env_name, dev);
> + tmp = env_get_mtdparts(env_name, tmp_mtdparts);
> + if (tmp) {
> + /* mtdids: "<dev>=<dev>, ...." */
> + if (mtdids[0] != '\0')
> + strcat(mtdids, ",");
> + strcat(mtdids, dev);
> + strcat(mtdids, "=");
> + strcat(mtdids, dev);
> +
> + /* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
> + if (mtdparts[0] != '\0')
> + strncat(mtdparts, ";", MTDPARTS_LEN);
> + else
> + strcat(mtdparts, "mtdparts=");
> + strncat(mtdparts, dev, MTDPARTS_LEN);
> + strncat(mtdparts, ":", MTDPARTS_LEN);
> + strncat(mtdparts, tmp, MTDPARTS_LEN);
> + }
> +}
> +
> +void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> +{
> + struct udevice *dev;
> + static char parts[3 * MTDPARTS_LEN + 1];
> + static char ids[MTDIDS_LEN + 1];
> + static bool mtd_initialized;
> +
> + if (mtd_initialized) {
> + *mtdids = ids;
> + *mtdparts = parts;
> + return;
> + }
> +
> + memset(parts, 0, sizeof(parts));
> + memset(ids, 0, sizeof(ids));
> +
> + /* probe all MTD devices */
> + for (uclass_first_device(UCLASS_MTD, &dev);
> + dev;
> + uclass_next_device(&dev)) {
> + pr_debug("mtd device = %s\n", dev->name);
> + }
> +
> + if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> + board_get_mtdparts("nor0", ids, parts);
> +
> + mtd_initialized = true;
> + *mtdids = ids;
> + *mtdparts = parts;
> + debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); } #endif
> +
> +#if defined(CONFIG_OF_BOARD_SETUP)
> +int ft_board_setup(void *blob, bd_t *bd) {
> + return 0;
> +}
> +#endif
> +
> +#ifdef CONFIG_SET_DFU_ALT_INFO
> +#define DFU_ALT_BUF_LEN SZ_1K
> +
> +static void board_get_alt_info(const char *dev, char *buff) {
> + char var_name[32] = "dfu_alt_info_";
> + int ret;
> +
> + ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
> +
> + /* name of env variable to read = dfu_alt_info_<dev> */
> + strcat(var_name, dev);
> + ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
> + if (ret) {
> + if (buff[0] != '\0')
> + strcat(buff, "&");
> + strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
> + }
> +}
> +
> +void set_dfu_alt_info(char *interface, char *devstr) {
> + struct udevice *dev;
> +
> + ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
> +
> + if (env_get("dfu_alt_info"))
> + return;
> +
> + memset(buf, 0, sizeof(buf));
> +
> + /* probe all MTD devices */
> + mtd_probe_devices();
> +
> + board_get_alt_info("ram", buf);
> +
> + if (!uclass_get_device(UCLASS_MMC, 0, &dev))
> + board_get_alt_info("mmc0", buf);
> +
> + if (!uclass_get_device(UCLASS_MMC, 1, &dev))
> + board_get_alt_info("mmc1", buf);
> +
> + if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> + board_get_alt_info("nor0", buf);
> +
> + env_set("dfu_alt_info", buf);
> + puts("DFU alt info setting: done\n");
> +}
> +#endif
> +
> +static void board_copro_image_process(ulong fw_image, size_t fw_size) {
> + int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
> +
> + if (!rproc_is_initialized())
> + if (rproc_init()) {
> + printf("Remote Processor %d initialization failed\n",
> + id);
> + return;
> + }
> +
> + ret = rproc_load(id, fw_image, fw_size);
> + printf("Load Remote Processor %d with data at addr=0x%08lx %u
> bytes:%s\n",
> + id, fw_image, fw_size, ret ? " Failed!" : " Success!");
> +
> + if (!ret) {
> + rproc_start(id);
> + env_set("copro_state", "booted");
> + }
> +}
> +
> +U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,
> board_copro_image_process);
> diff --git a/configs/stm32mp15_dhcom_basic_defconfig
> b/configs/stm32mp15_dhcom_basic_defconfig
> new file mode 100644
> index 0000000000..e4f331a913
> --- /dev/null
> +++ b/configs/stm32mp15_dhcom_basic_defconfig
> @@ -0,0 +1,140 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_STM32MP=y
> +CONFIG_SYS_MALLOC_F_LEN=0x3000
> +CONFIG_SPL_MMC_SUPPORT=y
> +CONFIG_ENV_SIZE=0x4000
> +CONFIG_SPL=y
> +CONFIG_TARGET_STM32MP1=y
> +# CONFIG_TARGET_STM32MP157C_DK2 is not set
CONFIG_TARGET_DH_STM32MP1_PDK2=y
> +CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y #
> +CONFIG_ARMV7_VIRT is not set
> +CONFIG_SPL_TEXT_BASE=0x2FFC2500
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_FIT=y
> +# CONFIG_BOOTSTAGE is not set
> +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> +CONFIG_SPL_I2C_SUPPORT=y
> +CONFIG_SPL_MTD_SUPPORT=y
> +CONFIG_SPL_POWER_SUPPORT=y
> +CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
> +CONFIG_SYS_PROMPT="STM32MP> "
> +# CONFIG_CMD_BOOTD is not set
> +# CONFIG_CMD_ELF is not set
> +# CONFIG_CMD_IMI is not set
> +# CONFIG_CMD_XIMG is not set
> +# CONFIG_CMD_EXPORTENV is not set
> +CONFIG_CMD_EEPROM=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_MEMTEST=y
> +CONFIG_CMD_ADC=y
> +CONFIG_CMD_CLK=y
> +CONFIG_CMD_DFU=y
> +CONFIG_CMD_FUSE=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_MTD=y
> +CONFIG_CMD_REMOTEPROC=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +CONFIG_CMD_BMP=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_TIMER=y
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_CMD_MTDPARTS=y
> +# CONFIG_SPL_DOS_PARTITION is not set
> +CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
> +CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-
> extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names
> assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_USE_ENV_SPI_BUS=y
> +CONFIG_ENV_SPI_BUS=0
> +CONFIG_USE_ENV_SPI_CS=y
> +CONFIG_ENV_SPI_CS=0
> +CONFIG_USE_ENV_SPI_MAX_HZ=y
> +CONFIG_ENV_SPI_MAX_HZ=10000000
> +CONFIG_USE_ENV_SPI_MODE=y
> +CONFIG_ENV_SPI_MODE=0x0
> +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_IP_DEFRAG=y
> +CONFIG_TFTP_BLOCKSIZE=1536
> +CONFIG_STM32_ADC=y
> +CONFIG_SPL_BLOCK_CACHE=y
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_DFU_VIRT=y
> +CONFIG_DM_HWSPINLOCK=y
> +CONFIG_HWSPINLOCK_STM32=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_STM32F7=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_DM_MAILBOX=y
> +CONFIG_STM32_IPCC=y
> +CONFIG_I2C_EEPROM=y
> +CONFIG_DM_MMC=y
> +CONFIG_SUPPORT_EMMC_BOOT=y
> +CONFIG_STM32_SDMMC2=y
> +CONFIG_MTD=y
> +CONFIG_DM_SPI_FLASH=y
> +CONFIG_SPI_FLASH_MACRONIX=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_SPI_FLASH_WINBOND=y
> +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> CONFIG_SPI_FLASH_MTD=y
> +CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y
> CONFIG_DWC_ETH_QOS=y
> +CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y #
> +CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
> +CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
> +CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> CONFIG_DM_REGULATOR_STM32_VREFBUF=y
> +CONFIG_DM_REGULATOR_STPMIC1=y
> +CONFIG_REMOTEPROC_STM32_COPRO=y
> +CONFIG_DM_RTC=y
> +CONFIG_RTC_STM32=y
> +CONFIG_SERIAL_RX_BUFFER=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_STM32_QSPI=y
> +CONFIG_STM32_SPI=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_DM_USB_GADGET=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="dh"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x0483
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
> +CONFIG_USB_GADGET_DWC2_OTG=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_BACKLIGHT_GPIO=y
> +CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
> +CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
> +CONFIG_VIDEO_STM32=y
> +CONFIG_VIDEO_STM32_DSI=y
> +CONFIG_VIDEO_STM32_MAX_XRES=1280
> +CONFIG_VIDEO_STM32_MAX_YRES=800
> +CONFIG_LZO=y
> +CONFIG_FDT_FIXUP_PARTITIONS=y
> --
> 2.24.1
>
Regards
Patrick
More information about the U-Boot
mailing list