[PATCH 5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board
Patrick DELAUNAY
patrick.delaunay at st.com
Fri Jan 17 17:32:16 CET 2020
Hi Marek,
> From: Patrick DELAUNAY
> Sent: lundi 13 janvier 2020 15:05
>
> Hi Marek,
>
> > From: Marek Vasut <marex at denx.de>
> > Sent: vendredi 10 janvier 2020 01:29
> >
> > Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board.
> > This is an SoM with STM32MP157C and an evaluation kit. The baseboard
> > provides Ethernet, UART, USB, CAN and optional display.
> > Signed-off-by: Marek Vasut <marex at denx.de>
> > Cc: Patrick Delaunay <patrick.delaunay at st.com>
> > Cc: Patrice Chotard <patrice.chotard at st.com>
> > ---
For information, I merge the serie, except this patch 5/5 on master brach and I sent a pull request for u-boot-stm32-20200117.
For this patch, I propose a rebase and also many modification liked to my previous remark
(I remove ST only parts for stboard command, and also led and key management) .
This proposal is present in the branch https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/next
https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/db48e11b1eccf23f3f9ba26e886a798e74df6a01
your initial patch is in applied https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh
Can you test the "next" branch and check the difference with your initial patch ( applied in dh branch
https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh
=> https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/0ab3ce72f82b946ac0924dfcdc082792f325eb68 )
I hope that I don't remove something really present on the SOM.
If you are OK, can you send a V2 version with the "next" branch content and I will integrate it in master branch for next pull request.
Thanks,
Patrick
> > arch/arm/dts/Makefile | 1 +
> > .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts | 7 +
> > arch/arm/dts/stm32mp157c-dhcom-pdk2.dts | 88 ++
> > arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi | 238 ++++++
> > arch/arm/dts/stm32mp157c-dhcom.dtsi | 379 +++++++++
> > arch/arm/mach-stm32mp/Kconfig | 1 +
> > board/dhelectronics/dh_stm32mp1/Kconfig | 25 +
> > board/dhelectronics/dh_stm32mp1/MAINTAINERS | 7 +
> > board/dhelectronics/dh_stm32mp1/Makefile | 12 +
> > board/dhelectronics/dh_stm32mp1/board.c | 777 ++++++++++++++++++
> > configs/stm32mp15_dhcom_basic_defconfig | 140 ++++
> > 11 files changed, 1675 insertions(+)
> > create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
> > create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
> > create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
> > create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
> > create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> > 983e235f44..82489bc09c 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
> > dtb-$(CONFIG_TARGET_STM32MP1) += \
> > stm32mp157a-dk1.dtb \
> > stm32mp157a-avenger96.dtb \
> > + stm32mp157c-dhcom-pdk2-u-boot.dtb \
> > stm32mp157c-dk2.dtb \
> > stm32mp157c-ed1.dtb \
> > stm32mp157c-ev1.dtb
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > new file mode 100644
> > index 0000000000..fd99988570
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > @@ -0,0 +1,7 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */
> > +
> > +#include "stm32mp157c-dhcom-pdk2.dts"
> > +#include "stm32mp157c-dhcom-u-boot.dtsi"
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > new file mode 100644
> > index 0000000000..05aa545f55
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > @@ -0,0 +1,88 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */
> > +
> > +#include "stm32mp157c-dhcom.dtsi"
> > +
> > +/ {
> > + model = "STMicroelectronics STM32MP157C DHCOM Premium
> > Developer Kit (2)";
> > + compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
> > +
> > + aliases {
> > + serial0 = &uart4;
> > + ethernet0 = ðernet0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + ethernet_vio: vioregulator {
> > + compatible = "regulator-fixed";
> > + regulator-name = "vio";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +};
> > +
> > +ðernet0 {
> > + status = "okay";
> > + pinctrl-0 = <ðernet0_rmii_pins_a>;
> > + pinctrl-1 = <ðernet0_rmii_pins_sleep_a>;
> > + pinctrl-names = "default", "sleep";
> > + phy-mode = "rmii";
> > + max-speed = <100>;
> > + phy-handle = <&phy0>;
> > + st,eth_ref_clk_sel;
> > + phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
> > +
> > + mdio0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "snps,dwmac-mdio";
> > +
> > + phy0: ethernet-phy at 1 {
> > + reg = <1>;
> > + };
> > + };
> > +};
> > +
> > +&pinctrl {
> > + ethernet0_rmii_pins_a: rmii-0 {
> > + pins1 {
> > + pinmux = <STM32_PINMUX('G', 13, AF11)>, /*
> > ETH1_RMII_TXD0 */
> > + <STM32_PINMUX('G', 14, AF11)>, /*
> > ETH1_RMII_TXD1 */
> > + <STM32_PINMUX('B', 11, AF11)>, /*
> > ETH1_RMII_TX_EN */
> > + <STM32_PINMUX('A', 1, AF0)>, /*
> > ETH1_RMII_REF_CLK */
> > + <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO
> > */
> > + <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC
> > */
> > + bias-disable;
> > + drive-push-pull;
> > + slew-rate = <2>;
> > + };
> > + pins2 {
> > + pinmux = <STM32_PINMUX('C', 4, AF11)>, /*
> > ETH1_RMII_RXD0 */
> > + <STM32_PINMUX('C', 5, AF11)>, /*
> > ETH1_RMII_RXD1 */
> > + <STM32_PINMUX('A', 7, AF11)>; /*
> > ETH1_RMII_CRS_DV */
> > + bias-disable;
> > + };
> > + };
> > +
> > + ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
> > + pins1 {
> > + pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*
> > ETH1_RMII_TXD0 */
> > + <STM32_PINMUX('G', 14, ANALOG)>, /*
> > ETH1_RMII_TXD1 */
> > + <STM32_PINMUX('B', 11, ANALOG)>, /*
> > ETH1_RMII_TX_EN */
> > + <STM32_PINMUX('A', 2, ANALOG)>, /*
> > ETH1_MDIO */
> > + <STM32_PINMUX('C', 1, ANALOG)>, /*
> > ETH1_MDC */
> > + <STM32_PINMUX('C', 4, ANALOG)>, /*
> > ETH1_RMII_RXD0 */
> > + <STM32_PINMUX('C', 5, ANALOG)>, /*
> > ETH1_RMII_RXD1 */
> > + <STM32_PINMUX('A', 1, ANALOG)>, /*
> > ETH1_RMII_REF_CLK */
> > + <STM32_PINMUX('A', 7, ANALOG)>; /*
> > ETH1_RMII_CRS_DV */
> > + };
> > + };
> > +};
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > new file mode 100644
> > index 0000000000..320912edd8
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > @@ -0,0 +1,238 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */
> > +
> > +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> > +#include "stm32mp157-u-boot.dtsi"
> > +#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
> > +
> > +/ {
> > + aliases {
> > + i2c1 = &i2c2;
> > + i2c3 = &i2c4;
> > + i2c4 = &i2c5;
> > + mmc0 = &sdmmc1;
> > + mmc1 = &sdmmc2;
> > + spi0 = &qspi;
> > + usb0 = &usbotg_hs;
> > + };
> > +
> > + config {
> > + u-boot,boot-led = "heartbeat";
> > + u-boot,error-led = "error";
>
> Excpet if I miss something, You have no led on your board (named = "heartbeat"
> or "error" ) This 2 line can be remove I think
>
> > + st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> > + st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
> > + };
> > +
> > + led {
> > + red {
> > + label = "error";
> > + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> > + default-state = "off";
> > + status = "okay";
> > + };
> > +
> > + blue {
> > + default-state = "on";
> > + };
> > + };
>
> This blue overridde can be remove I think.
>
> > +};
> > +
> > +&i2c4 {
> > + u-boot,dm-pre-reloc;
> > +};
> > +
> > +&i2c4_pins_a {
> > + u-boot,dm-pre-reloc;
> > + pins {
> > + u-boot,dm-pre-reloc;
> > + };
> > +};
> > +
> > +&pmic {
> > + u-boot,dm-pre-reloc;
> > +};
> > +
> > +&flash0 {
> > + u-boot,dm-spl;
> > +};
> > +
> > +&qspi {
> > + u-boot,dm-spl;
> > +};
> > +
> > +&qspi_clk_pins_a {
> > + u-boot,dm-spl;
> > + pins {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&qspi_bk1_pins_a {
> > + u-boot,dm-spl;
> > + pins1 {
> > + u-boot,dm-spl;
> > + };
> > + pins2 {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&qspi_bk2_pins_a {
> > + u-boot,dm-spl;
> > + pins1 {
> > + u-boot,dm-spl;
> > + };
> > + pins2 {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&rcc {
> > + st,clksrc = <
> > + CLK_MPU_PLL1P
> > + CLK_AXI_PLL2P
> > + CLK_MCU_PLL3P
> > + CLK_PLL12_HSE
> > + CLK_PLL3_HSE
> > + CLK_PLL4_HSE
> > + CLK_RTC_LSE
> > + CLK_MCO1_DISABLED
> > + CLK_MCO2_DISABLED
> > + >;
> > +
> > + st,clkdiv = <
> > + 1 /*MPU*/
> > + 0 /*AXI*/
> > + 0 /*MCU*/
> > + 1 /*APB1*/
> > + 1 /*APB2*/
> > + 1 /*APB3*/
> > + 1 /*APB4*/
> > + 2 /*APB5*/
> > + 23 /*RTC*/
> > + 0 /*MCO1*/
> > + 0 /*MCO2*/
> > + >;
> > +
> > + st,pkcs = <
> > + CLK_CKPER_HSE
> > + CLK_FMC_ACLK
> > + CLK_QSPI_ACLK
> > + CLK_ETH_PLL4P
> > + CLK_SDMMC12_PLL4P
> > + CLK_DSI_DSIPLL
> > + CLK_STGEN_HSE
> > + CLK_USBPHY_HSE
> > + CLK_SPI2S1_PLL3Q
> > + CLK_SPI2S23_PLL3Q
> > + CLK_SPI45_HSI
> > + CLK_SPI6_HSI
> > + CLK_I2C46_HSI
> > + CLK_SDMMC3_PLL4P
> > + CLK_USBO_USBPHY
> > + CLK_ADC_CKPER
> > + CLK_CEC_LSE
> > + CLK_I2C12_HSI
> > + CLK_I2C35_HSI
> > + CLK_UART1_HSI
> > + CLK_UART24_HSI
> > + CLK_UART35_HSI
> > + CLK_UART6_HSI
> > + CLK_UART78_HSI
> > + CLK_SPDIF_PLL4P
> > + CLK_FDCAN_PLL4Q
> > + CLK_SAI1_PLL3Q
> > + CLK_SAI2_PLL3Q
> > + CLK_SAI3_PLL3Q
> > + CLK_SAI4_PLL3Q
> > + CLK_RNG1_LSI
> > + CLK_RNG2_LSI
> > + CLK_LPTIM1_PCLK1
> > + CLK_LPTIM23_PCLK3
> > + CLK_LPTIM45_LSE
> > + >;
> > +
> > + /* VCO = 1300.0 MHz => P = 650 (CPU) */
> > + pll1: st,pll at 0 {
> > + cfg = < 2 80 0 0 0 PQR(1,0,0) >;
> > + frac = < 0x800 >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +
> > + /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
> > + pll2: st,pll at 1 {
> > + cfg = < 2 65 1 0 0 PQR(1,1,1) >;
> > + frac = < 0x1400 >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +
> > + /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
> > + pll3: st,pll at 2 {
> > + cfg = < 1 33 1 16 36 PQR(1,1,1) >;
> > + frac = < 0x1a04 >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +
> > + /* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
> > + pll4: st,pll at 3 {
> > + cfg = < 1 49 11 11 11 PQR(1,1,1) >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +};
> > +
> > +&sdmmc1 {
> > + u-boot,dm-spl;
> > +};
> > +
> > +&sdmmc1_b4_pins_a {
> > + u-boot,dm-spl;
> > + pins {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&sdmmc1_dir_pins_a {
> > + u-boot,dm-spl;
> > + pins1 {
> > + u-boot,dm-spl;
> > + };
> > + pins2 {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&sdmmc2 {
> > + u-boot,dm-spl;
> > +};
> > +
> > +&sdmmc2_b4_pins_a {
> > + u-boot,dm-spl;
> > + pins {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&sdmmc2_d47_pins_a {
> > + u-boot,dm-spl;
> > + pins {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&uart4 {
> > + u-boot,dm-pre-reloc;
> > +};
> > +
> > +&uart4_pins_a {
> > + u-boot,dm-pre-reloc;
> > + pins1 {
> > + u-boot,dm-pre-reloc;
> > + };
> > + pins2 {
> > + u-boot,dm-pre-reloc;
> > + /* pull-up on rx to avoid floating level */
> > + bias-pull-up;
> > + };
> > +};
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom.dtsi
> > b/arch/arm/dts/stm32mp157c- dhcom.dtsi new file mode 100644 index
> > 0000000000..96661ae783
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom.dtsi
> > @@ -0,0 +1,379 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de> */ /dts-v1/;
> > +
> > +#include "stm32mp157c.dtsi"
> > +#include "stm32mp157xaa-pinctrl.dtsi"
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/mfd/st,stpmic1.h>
> > +
> > +/ {
> > + memory at c0000000 {
> > + device_type = "memory";
> > + reg = <0xC0000000 0x40000000>;
> > + };
> > +};
> > +
> > +&cec {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&cec_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&dcmi {
> > + status = "okay";
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&dcmi_pins_a>;
> > + pinctrl-1 = <&dcmi_sleep_pins_a>;
> > +};
> > +
> > +&dts {
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c2_pins_a>;
> > + i2c-scl-rising-time-ns = <185>;
> > + i2c-scl-falling-time-ns = <20>;
> > + status = "okay";
> > +};
> > +
> > +&i2c4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c4_pins_a>;
> > + i2c-scl-rising-time-ns = <185>;
> > + i2c-scl-falling-time-ns = <20>;
> > + status = "okay";
> > + /* spare dmas for other usage */
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > +
> > + pmic: stpmic at 33 {
> > + compatible = "st,stpmic1";
> > + reg = <0x33>;
> > + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + status = "okay";
> > +
> > + regulators {
> > + compatible = "st,stpmic1-regulators";
> > + ldo1-supply = <&v3v3>;
> > + ldo2-supply = <&v3v3>;
> > + ldo3-supply = <&vdd_ddr>;
> > + ldo5-supply = <&v3v3>;
> > + ldo6-supply = <&v3v3>;
> > + pwr_sw1-supply = <&bst_out>;
> > + pwr_sw2-supply = <&bst_out>;
> > +
> > + vddcore: buck1 {
> > + regulator-name = "vddcore";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-always-on;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd_ddr: buck2 {
> > + regulator-name = "vdd_ddr";
> > + regulator-min-microvolt = <1350000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-always-on;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd: buck3 {
> > + regulator-name = "vdd";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + st,mask-reset;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + v3v3: buck4 {
> > + regulator-name = "v3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + regulator-initial-mode = <0>;
> > + };
> > +
> > + vdda: ldo1 {
> > + regulator-name = "vdda";
> > + regulator-min-microvolt = <2900000>;
> > + regulator-max-microvolt = <2900000>;
> > + interrupts = <IT_CURLIM_LDO1 0>;
> > + };
> > +
> > + v2v8: ldo2 {
> > + regulator-name = "v2v8";
> > + regulator-min-microvolt = <2800000>;
> > + regulator-max-microvolt = <2800000>;
> > + interrupts = <IT_CURLIM_LDO2 0>;
> > + };
> > +
> > + vtt_ddr: ldo3 {
> > + regulator-name = "vtt_ddr";
> > + regulator-min-microvolt = <500000>;
> > + regulator-max-microvolt = <750000>;
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd_usb: ldo4 {
> > + regulator-name = "vdd_usb";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + interrupts = <IT_CURLIM_LDO4 0>;
> > + };
> > +
> > + vdd_sd: ldo5 {
> > + regulator-name = "vdd_sd";
> > + regulator-min-microvolt = <2900000>;
> > + regulator-max-microvolt = <2900000>;
> > + interrupts = <IT_CURLIM_LDO5 0>;
> > + regulator-boot-on;
> > + };
> > +
> > + v1v8: ldo6 {
> > + regulator-name = "v1v8";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + interrupts = <IT_CURLIM_LDO6 0>;
> > + };
> > +
> > + vref_ddr: vref_ddr {
> > + regulator-name = "vref_ddr";
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + };
> > +
> > + bst_out: boost {
> > + regulator-name = "bst_out";
> > + interrupts = <IT_OCP_BOOST 0>;
> > + };
> > +
> > + vbus_otg: pwr_sw1 {
> > + regulator-name = "vbus_otg";
> > + interrupts = <IT_OCP_OTG 0>;
> > + };
> > +
> > + vbus_sw: pwr_sw2 {
> > + regulator-name = "vbus_sw";
> > + interrupts = <IT_OCP_SWOUT 0>;
> > + regulator-active-discharge;
> > + };
> > + };
> > +
> > + onkey {
> > + compatible = "st,stpmic1-onkey";
> > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> > + interrupt-names = "onkey-falling", "onkey-rising";
> > + power-off-time-sec = <10>;
> > + status = "okay";
> > + };
> > +
> > + watchdog {
> > + compatible = "st,stpmic1-wdt";
> > + status = "disabled";
> > + };
> > + };
> > +
> > + eeprom at 50 {
> > + compatible = "atmel,24c02";
> > + reg = <0x50>;
> > + pagesize = <16>;
> > + };
> > +};
> > +
> > +&i2c5 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c5_pins_a>;
> > + i2c-scl-rising-time-ns = <185>;
> > + i2c-scl-falling-time-ns = <20>;
> > + status = "okay";
> > +};
> > +
> > +&ipcc {
> > + status = "okay";
> > +};
> > +
> > +&iwdg2 {
> > + timeout-sec = <32>;
> > + status = "okay";
> > +};
> > +
> > +&m4_rproc {
> > + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> > + mbox-names = "vq0", "vq1", "shutdown";
> > + status = "okay";
> > +};
> > +
> > +&pwr {
> > + pwr-regulators {
> > + vdd-supply = <&vdd>;
> > + vdd_3v3_usbfs-supply = <&vdd_usb>;
> > + };
> > +};
> > +
> > +&qspi {
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
> > + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a
> > &qspi_bk2_sleep_pins_a>;
> > + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + status = "okay";
> > +
> > + flash0: mx66l51235l at 0 {
> > + compatible = "jedec,spi-nor";
> > + reg = <0>;
> > + spi-rx-bus-width = <4>;
> > + spi-max-frequency = <108000000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + };
> > +
> > + flash1: mx66l51235l at 1 {
> > + compatible = "jedec,spi-nor";
> > + reg = <1>;
> > + spi-rx-bus-width = <4>;
> > + spi-max-frequency = <108000000>;
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + };
> > +};
> > +
> > +&rng1 {
> > + status = "okay";
> > +};
> > +
> > +&rtc {
> > + status = "okay";
> > +};
> > +
> > +&sdmmc1 {
> > + pinctrl-names = "default", "opendrain", "sleep";
> > + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> > + pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
> > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
> > + broken-cd;
> > + st,sig-dir;
> > + st,neg-edge;
> > + st,use-ckin;
> > + bus-width = <4>;
> > + vmmc-supply = <&vdd_sd>;
> > + status = "okay";
> > +};
> > +
> > +&sdmmc2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> > + non-removable;
> > + no-sd;
> > + no-sdio;
> > + st,sig-dir;
> > + st,neg-edge;
> > + bus-width = <8>;
> > + vmmc-supply = <&v3v3>;
> > + status = "okay";
> > +};
> > +
> > +&spi1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&spi1_pins_a>;
> > + status = "disabled";
> > +};
> > +
> > +&timers2 {
> > + /* spare dmas for other usage (un-delete to enable pwm capture) */
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm2_pins_a>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > + };
> > + timer at 1 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers6 {
> > + status = "okay";
> > + /* spare dmas for other usage */
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + timer at 5 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers8 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm8_pins_a>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > + };
> > + timer at 7 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers12 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm12_pins_a>;
> > + pinctrl-names = "default";
> > + status = "okay";
> > + };
> > + timer at 11 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart4_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&usbh_ehci {
> > + phys = <&usbphyc_port0>;
> > + phy-names = "usb";
> > + status = "okay";
> > +};
> > +
> > +&usbotg_hs {
> > + dr_mode = "peripheral";
> > + phys = <&usbphyc_port1 0>;
> > + phy-names = "usb2-phy";
> > + vbus-supply = <&vbus_otg>;
> > + status = "okay";
> > +};
> > +
> > +&usbphyc {
> > + status = "okay";
> > +};
> > +
> > +&usbphyc_port0 {
> > + phy-supply = <&vdd_usb>;
> > +};
> > +
> > +&usbphyc_port1 {
> > + phy-supply = <&vdd_usb>;
> > +};
> > diff --git a/arch/arm/mach-stm32mp/Kconfig
> > b/arch/arm/mach-stm32mp/Kconfig index ae28f6e206..1aa5f8a122 100644
> > --- a/arch/arm/mach-stm32mp/Kconfig
> > +++ b/arch/arm/mach-stm32mp/Kconfig
> > @@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK endif
> >
> > source "board/st/stm32mp1/Kconfig"
> > +source "board/dhelectronics/dh_stm32mp1/Kconfig"
> >
> > endif
> > diff --git a/board/dhelectronics/dh_stm32mp1/Kconfig
> > b/board/dhelectronics/dh_stm32mp1/Kconfig
> > new file mode 100644
> > index 0000000000..e751a3e5ed
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/Kconfig
> > @@ -0,0 +1,25 @@
> > +config TARGET_DH_STM32MP1_PDK2
> > + bool "support of DH STM32MP1 PDK2"
> > + default y
>
> Avoid set default y here....
> to avoid to activate this config for ST board.
>
> In fact it should be a choice between the 2 targets
> - TARGET_DH_STM32MP1_PDK2
> - TARGET_ST_STM32MP1
>
> > +
> > +if TARGET_DH_STM32MP1_PDK2
> > +
> > +config SYS_BOARD
> > + default "dh_stm32mp1"
> > +
> > +config SYS_VENDOR
> > + default "dhelectronics"
> > +
> > +config SYS_CONFIG_NAME
> > + default "stm32mp1"
> > +
> > +config ENV_SECT_SIZE
> > + default 0x10000 if ENV_IS_IN_SPI_FLASH
> > +
> > +config ENV_OFFSET
> > + default 0x1E0000 if ENV_IS_IN_SPI_FLASH
> > +
> > +config ENV_OFFSET_REDUND
> > + default 0x1F0000 if ENV_IS_IN_SPI_FLASH
> > +
> > +endif
> > diff --git a/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > new file mode 100644
> > index 0000000000..38f54a3da4
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > @@ -0,0 +1,7 @@
> > +DH_STM32MP1_PDK2 BOARD
> > +M: Marek Vasut <marex at denx.de>
> > +S: Maintained
> > +F: arch/arm/dts/stm32mp157c-dhcom*
> > +F: board/dhelectronics/dh_stm32mp1/
> > +F: configs/stm32mp15_dhcom_basic_defconfig
> > +F: include/configs/stm32mp1.h
> > diff --git a/board/dhelectronics/dh_stm32mp1/Makefile
> > b/board/dhelectronics/dh_stm32mp1/Makefile
> > new file mode 100644
> > index 0000000000..a9d28218ef
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/Makefile
> > @@ -0,0 +1,12 @@
> > +# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
> > +2018, STMicroelectronics - All Rights Reserved #
> > +
> > +ifdef CONFIG_SPL_BUILD
> > +obj-y += ../../st/stm32mp1/spl.o
> > +else
> > +obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif
> > +
>
> I don't think you wee to support the command STMicroelctronics board (ref
> MBxxxx).
> it is only a internal command for ST : save/read board id in OTP.
>
> > +obj-y += ../../st/stm32mp1/board.o board.o
> > diff --git a/board/dhelectronics/dh_stm32mp1/board.c
> > b/board/dhelectronics/dh_stm32mp1/board.c
> > new file mode 100644
> > index 0000000000..54cc3b7587
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/board.c
> > @@ -0,0 +1,777 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved */
> > +
> > +#include <common.h>
> > +#include <adc.h>
> > +#include <asm/arch/stm32.h>
> > +#include <asm/arch/sys_proto.h>
> > +#include <asm/gpio.h>
> > +#include <asm/io.h>
> > +#include <bootm.h>
> > +#include <clk.h>
> > +#include <config.h>
> > +#include <dm.h>
> > +#include <dm/device.h>
> > +#include <dm/uclass.h>
> > +#include <env.h>
> > +#include <env_internal.h>
> > +#include <g_dnl.h>
> > +#include <generic-phy.h>
> > +#include <i2c.h>
> > +#include <i2c_eeprom.h>
> > +#include <init.h>
> > +#include <led.h>
> > +#include <memalign.h>
> > +#include <misc.h>
> > +#include <mtd.h>
> > +#include <mtd_node.h>
> > +#include <netdev.h>
> > +#include <phy.h>
> > +#include <power/regulator.h>
> > +#include <remoteproc.h>
> > +#include <reset.h>
> > +#include <syscon.h>
> > +#include <usb.h>
> > +#include <usb/dwc2_udc.h>
> > +#include <watchdog.h>
> > +
> > +/* SYSCFG registers */
> > +#define SYSCFG_BOOTR 0x00
> > +#define SYSCFG_PMCSETR 0x04
> > +#define SYSCFG_IOCTRLSETR 0x18
> > +#define SYSCFG_ICNR 0x1C
> > +#define SYSCFG_CMPCR 0x20
> > +#define SYSCFG_CMPENSETR 0x24
> > +#define SYSCFG_PMCCLRR 0x44
> > +
> > +#define SYSCFG_BOOTR_BOOT_MASK GENMASK(2, 0)
> > +#define SYSCFG_BOOTR_BOOTPD_SHIFT 4
> > +
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE BIT(0)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI BIT(1)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_ETH BIT(2)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC BIT(3)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_SPI BIT(4)
> > +
> > +#define SYSCFG_CMPCR_SW_CTRL BIT(1)
> > +#define SYSCFG_CMPCR_READY BIT(8)
> > +
> > +#define SYSCFG_CMPENSETR_MPU_EN BIT(0)
> > +
> > +#define SYSCFG_PMCSETR_ETH_CLK_SEL BIT(16)
> > +#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL BIT(17)
> > +
> > +#define SYSCFG_PMCSETR_ETH_SELMII BIT(20)
> > +
> > +#define SYSCFG_PMCSETR_ETH_SEL_MASK GENMASK(23, 21)
> > +#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII 0
> > +#define SYSCFG_PMCSETR_ETH_SEL_RGMII BIT(21)
> > +#define SYSCFG_PMCSETR_ETH_SEL_RMII BIT(23)
> > +
> > +/*
> > + * Get a global data pointer
> > + */
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +int setup_mac_address(void)
> > +{
> > + struct udevice *dev;
> > + ofnode eeprom;
> > + unsigned char enetaddr[6];
> > + int ret;
> > +
> > + ret = eth_env_get_enetaddr("ethaddr", enetaddr);
> > + if (ret) /* ethaddr is already set */
> > + return 0;
> > +
> > + eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
> > + if (!ofnode_valid(eeprom)) {
> > + printf("Invalid hardware path to EEPROM!\n");
> > + return -ENODEV;
> > + }
> > +
> > + ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,
> > &dev);
> > + if (ret) {
> > + printf("Cannot find EEPROM!\n");
> > + return ret;
> > + }
> > +
> > + ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
> > + if (ret) {
> > + printf("Error reading configuration EEPROM!\n");
> > + return ret;
> > + }
> > +
> > + if (is_valid_ethaddr(enetaddr))
> > + eth_env_set_enetaddr("ethaddr", enetaddr);
> > +
> > + return 0;
> > +}
> > +
> > +int checkboard(void)
> > +{
> > + int ret;
> > + char *mode;
> > + u32 otp;
> > + struct udevice *dev;
> > + const char *fdt_compat;
> > + int fdt_compat_len;
> > +
> > + if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
> > + mode = "trusted with OP-TEE";
> > + else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
> > + mode = "trusted";
> > + else
> > + mode = "basic";
> > +
> > + printf("Board: stm32mp1 in %s mode", mode);
> > + fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> > + &fdt_compat_len);
> > + if (fdt_compat && fdt_compat_len)
> > + printf(" (%s)", fdt_compat);
> > + puts("\n");
> > +
> > + ret = uclass_get_device_by_driver(UCLASS_MISC,
> > + DM_GET_DRIVER(stm32mp_bsec),
> > + &dev);
> > +
> > + if (!ret)
> > + ret = misc_read(dev,
> > STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> > + &otp, sizeof(otp));
> > + if (ret > 0 && otp) {
> > + printf("Board: MB%04x Var%d Rev.%c-%02d\n",
> > + otp >> 16,
> > + (otp >> 12) & 0xF,
> > + ((otp >> 8) & 0xF) - 1 + 'A',
> > + otp & 0xF);
> > + }
>
> This part (read OTP / / display MBxxx ) can be dropped for your board (it is a ST
> specific part).
>
> > + return 0;
> > +}
> > +
> > +static void board_key_check(void)
> > +{
> > +#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
> > + ofnode node;
> > + struct gpio_desc gpio;
> > + enum forced_boot_mode boot_mode = BOOT_NORMAL;
> > +
> > + node = ofnode_path("/config");
> > + if (!ofnode_valid(node)) {
> > + debug("%s: no /config node?\n", __func__);
> > + return;
> > + }
> > +#ifdef CONFIG_FASTBOOT
> > + if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
> > + &gpio, GPIOD_IS_IN)) {
> > + debug("%s: could not find a /config/st,fastboot-gpios\n",
> > + __func__);
> > + } else {
> > + if (dm_gpio_get_value(&gpio)) {
> > + puts("Fastboot key pressed, ");
> > + boot_mode = BOOT_FASTBOOT;
> > + }
> > +
> > + dm_gpio_free(NULL, &gpio);
> > + }
> > +#endif
> > +#ifdef CONFIG_CMD_STM32PROG
> > + if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
> > + &gpio, GPIOD_IS_IN)) {
> > + debug("%s: could not find a /config/st,stm32prog-gpios\n",
> > + __func__);
> > + } else {
> > + if (dm_gpio_get_value(&gpio)) {
> > + puts("STM32Programmer key pressed, ");
> > + boot_mode = BOOT_STM32PROG;
> > + }
> > + dm_gpio_free(NULL, &gpio);
> > + }
> > +#endif
> > +
> > + if (boot_mode != BOOT_NORMAL) {
> > + puts("entering download mode...\n");
> > + clrsetbits_le32(TAMP_BOOT_CONTEXT,
> > + TAMP_BOOT_FORCED_MASK,
> > + boot_mode);
> > + }
> > +#endif
> > +}
>
> Do you support GPIO key press on GPAIOA14 / 15 (as it is done in ST boards
> EV1 : DK1 / DK2) If no all this function can be dropped.
>
> > +#if defined(CONFIG_USB_GADGET) &&
> > defined(CONFIG_USB_GADGET_DWC2_OTG)
> > +
> > +/* STMicroelectronics STUSB1600 Type-C controller */
> > +#define STUSB1600_CC_CONNECTION_STATUS 0x0E
> > +
> > +/* STUSB1600_CC_CONNECTION_STATUS bitfields */
> > +#define STUSB1600_CC_ATTACH BIT(0)
> > +
> > +static int stusb1600_init(struct udevice **dev_stusb1600) {
> > + ofnode node;
> > + struct udevice *dev, *bus;
> > + int ret;
> > + u32 chip_addr;
> > +
> > + *dev_stusb1600 = NULL;
> > +
> > + /* if node stusb1600 is present, means DK1 or DK2 board */
> > + node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
> > + if (!ofnode_valid(node))
> > + return -ENODEV;
> > +
> > + ret = ofnode_read_u32(node, "reg", &chip_addr);
> > + if (ret)
> > + return -EINVAL;
> > +
> > + ret = uclass_get_device_by_ofnode(UCLASS_I2C,
> > ofnode_get_parent(node),
> > + &bus);
> > + if (ret) {
> > + printf("bus for stusb1600 not found\n");
> > + return -ENODEV;
> > + }
> > +
> > + ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
> > + if (!ret)
> > + *dev_stusb1600 = dev;
> > +
> > + return ret;
> > +}
> > +
> > +static int stusb1600_cable_connected(struct udevice *dev) {
> > + u8 status;
> > +
> > + if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,
> > 1))
> > + return 0;
> > +
> > + return status & STUSB1600_CC_ATTACH; }
> > +
> > +#include <usb/dwc2_udc.h>
> > +int g_dnl_board_usb_cable_connected(void)
> > +{
> > + struct udevice *stusb1600;
> > + struct udevice *dwc2_udc_otg;
> > + int ret;
> > +
> > + if (!stusb1600_init(&stusb1600))
> > + return stusb1600_cable_connected(stusb1600);
> > +
> > + ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
> > + DM_GET_DRIVER(dwc2_udc_otg),
> > + &dwc2_udc_otg);
> > + if (!ret)
> > + debug("dwc2_udc_otg init failed\n");
> > +
> > + return dwc2_udc_B_session_valid(dwc2_udc_otg);
> > +}
> > +
>
> If you don't have STUSB1600 (external usb typeC controller) All this part can
> dropped.
>
> > +#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
> > +STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
> > +
> > +int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
> > +*name) {
> > + if (!strcmp(name, "usb_dnl_dfu"))
> > + put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
> > >idProduct);
> > + else if (!strcmp(name, "usb_dnl_fastboot"))
> > +
> > put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,
> > + &dev->idProduct);
> > + else
> > + put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
> > >idProduct);
> > +
> > + return 0;
> > +}
> > +
> > +#endif /* CONFIG_USB_GADGET */
> > +
> > +#ifdef CONFIG_LED
> > +static int get_led(struct udevice **dev, char *led_string) {
> > + char *led_name;
> > + int ret;
> > +
> > + led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
> > + if (!led_name) {
> > + pr_debug("%s: could not find %s config string\n",
> > + __func__, led_string);
> > + return -ENOENT;
> > + }
> > + ret = led_get_by_label(led_name, dev);
> > + if (ret) {
> > + debug("%s: get=%d\n", __func__, ret);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int setup_led(enum led_state_t cmd) {
> > + struct udevice *dev;
> > + int ret;
> > +
> > + ret = get_led(&dev, "u-boot,boot-led");
> > + if (ret)
> > + return ret;
> > +
> > + ret = led_set_state(dev, cmd);
> > + return ret;
> > +}
> > +#endif
> > +
> > +static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
> > +CONFIG_LED
> > + int ret;
> > + struct udevice *led;
> > + u32 i;
> > +#endif
> > +
> > + if (!nb_blink)
> > + return;
> > +
> > +#ifdef CONFIG_LED
> > + ret = get_led(&led, "u-boot,error-led");
> > + if (!ret) {
> > + /* make u-boot,error-led blinking */
> > + /* if U32_MAX and 125ms interval, for 17.02 years */
> > + for (i = 0; i < 2 * nb_blink; i++) {
> > + led_set_state(led, LEDST_TOGGLE);
> > + mdelay(125);
> > + WATCHDOG_RESET();
> > + }
> > + }
> > +#endif
> > +
> > + /* infinite: the boot process must be stopped */
> > + if (nb_blink == U32_MAX)
> > + hang();
> > +}
> > +
> > +static void sysconf_init(void)
> > +{
> > +#ifndef CONFIG_STM32MP1_TRUSTED
> > + u8 *syscfg;
> > +#ifdef CONFIG_DM_REGULATOR
> > + struct udevice *pwr_dev;
> > + struct udevice *pwr_reg;
> > + struct udevice *dev;
> > + int ret;
> > + u32 otp = 0;
> > +#endif
> > + u32 bootr;
> > +
> > + syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> > +
> > + /* interconnect update : select master using the port 1 */
> > + /* LTDC = AXI_M9 */
> > + /* GPU = AXI_M8 */
> > + /* today information is hardcoded in U-Boot */
> > + writel(BIT(9), syscfg + SYSCFG_ICNR);
> > +
> > + /* disable Pull-Down for boot pin connected to VDD */
> > + bootr = readl(syscfg + SYSCFG_BOOTR);
> > + bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<
> > SYSCFG_BOOTR_BOOTPD_SHIFT);
> > + bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<
> > SYSCFG_BOOTR_BOOTPD_SHIFT;
> > + writel(bootr, syscfg + SYSCFG_BOOTR);
> > +
> > +#ifdef CONFIG_DM_REGULATOR
> > + /* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,
> > QSPI
> > + * and TRACE. Needed above ~50MHz and conditioned by AFMUX
> > selection.
> > + * The customer will have to disable this for low frequencies
> > + * or if AFMUX is selected but the function not used, typically for
> > + * TRACE. Otherwise, impact on power consumption.
> > + *
> > + * WARNING:
> > + * enabling High Speed mode while VDD>2.7V
> > + * with the OTP product_below_2v5 (OTP 18, BIT 13)
> > + * erroneously set to 1 can damage the IC!
> > + * => U-Boot set the register only if VDD < 2.7V (in DT)
> > + * but this value need to be consistent with board design
> > + */
> > + ret = uclass_get_device_by_driver(UCLASS_PMIC,
> > + DM_GET_DRIVER(stm32mp_pwr_pmic),
> > + &pwr_dev);
> > + if (!ret) {
> > + ret = uclass_get_device_by_driver(UCLASS_MISC,
> > +
> > DM_GET_DRIVER(stm32mp_bsec),
> > + &dev);
> > + if (ret) {
> > + pr_err("Can't find stm32mp_bsec driver\n");
> > + return;
> > + }
> > +
> > + ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
> > + if (ret > 0)
> > + otp = otp & BIT(13);
> > +
> > + /* get VDD = vdd-supply */
> > + ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
> > + &pwr_reg);
> > +
> > + /* check if VDD is Low Voltage */
> > + if (!ret) {
> > + if (regulator_get_value(pwr_reg) < 2700000) {
> > + writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
> > + SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI
> > |
> > + SYSCFG_IOCTRLSETR_HSLVEN_ETH |
> > + SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
> > + SYSCFG_IOCTRLSETR_HSLVEN_SPI,
> > + syscfg + SYSCFG_IOCTRLSETR);
> > +
> > + if (!otp)
> > + pr_err("product_below_2v5=0: HSLVEN
> > protected by HW\n");
> > + } else {
> > + if (otp)
> > + pr_err("product_below_2v5=1: HSLVEN
> > update is destructive, no update as VDD>2.7V\n");
> > + }
> > + } else {
> > + debug("VDD unknown");
> > + }
> > + }
> > +#endif
> > +
> > + /* activate automatic I/O compensation
> > + * warning: need to ensure CSI enabled and ready in clock driver
> > + */
> > + writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +
> > SYSCFG_CMPENSETR);
> > +
> > + while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
> > + ;
> > + clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
> > #endif }
> > +
> > +/* board dependent setup after realloc */ int board_init(void) {
> > + struct udevice *dev;
> > +
> > + /* address of boot parameters */
> > + gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
> > +
> > + /* probe all PINCTRL for hog */
> > + for (uclass_first_device(UCLASS_PINCTRL, &dev);
> > + dev;
> > + uclass_next_device(&dev)) {
> > + pr_debug("probe pincontrol = %s\n", dev->name);
> > + }
> > +
> > + board_key_check();
> > +
> > +#ifdef CONFIG_DM_REGULATOR
> > + regulators_enable_boot_on(_DEBUG);
> > +#endif
> > +
> > + sysconf_init();
> > +
> > + if (CONFIG_IS_ENABLED(CONFIG_LED))
> > + led_default_state();
> > +
> > + return 0;
> > +}
> > +
> > +int board_late_init(void)
> > +{
> > + char *boot_device;
> > +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> > + const void *fdt_compat;
> > + int fdt_compat_len;
> > + int ret;
> > + u32 otp;
> > + struct udevice *dev;
> > + char buf[10];
> > +
> > + fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> > + &fdt_compat_len);
> > + if (fdt_compat && fdt_compat_len) {
> > + if (strncmp(fdt_compat, "st,", 3) != 0)
> > + env_set("board_name", fdt_compat);
> > + else
> > + env_set("board_name", fdt_compat + 3);
> > + }
> > + ret = uclass_get_device_by_driver(UCLASS_MISC,
> > + DM_GET_DRIVER(stm32mp_bsec),
> > + &dev);
> > +
> > + if (!ret)
> > + ret = misc_read(dev,
> > STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> > + &otp, sizeof(otp));
> > + if (!ret && otp) {
> > + snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
> > + env_set("board_id", buf);
> > +
> > + snprintf(buf, sizeof(buf), "0x%04x",
> > + ((otp >> 8) & 0xF) - 1 + 0xA);
> > + env_set("board_rev", buf);
> > + }
> > +#endif
> > +
> > + /* Check the boot-source to disable bootdelay */
> > + boot_device = env_get("boot_device");
> > + if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
> > + env_set("bootdelay", "0");
> > +
> > + return 0;
> > +}
> > +
> > +void board_quiesce_devices(void)
> > +{
> > +#ifdef CONFIG_LED
> > + setup_led(LEDST_OFF);
> > +#endif
> > +}
> > +
> > +/* eth init function : weak called in eqos driver */ int
> > +board_interface_eth_init(struct udevice *dev,
> > + phy_interface_t interface_type) {
> > + u8 *syscfg;
> > + u32 value;
> > + bool eth_clk_sel_reg = false;
> > + bool eth_ref_clk_sel_reg = false;
> > +
> > + /* Gigabit Ethernet 125MHz clock selection. */
> > + eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
> > +
> > + /* Ethernet 50Mhz RMII clock selection */
> > + eth_ref_clk_sel_reg =
> > + dev_read_bool(dev, "st,eth_ref_clk_sel");
> > +
> > + syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> > +
> > + if (!syscfg)
> > + return -ENODEV;
> > +
> > + switch (interface_type) {
> > + case PHY_INTERFACE_MODE_MII:
> > + value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> > + SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> > + debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
> > + break;
> > + case PHY_INTERFACE_MODE_GMII:
> > + if (eth_clk_sel_reg)
> > + value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> > + SYSCFG_PMCSETR_ETH_CLK_SEL;
> > + else
> > + value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
> > + debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
> > + break;
> > + case PHY_INTERFACE_MODE_RMII:
> > + if (eth_ref_clk_sel_reg)
> > + value = SYSCFG_PMCSETR_ETH_SEL_RMII |
> > + SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> > + else
> > + value = SYSCFG_PMCSETR_ETH_SEL_RMII;
> > + debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
> > + break;
> > + case PHY_INTERFACE_MODE_RGMII:
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > + if (eth_clk_sel_reg)
> > + value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
> > + SYSCFG_PMCSETR_ETH_CLK_SEL;
> > + else
> > + value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
> > + debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
> > + break;
> > + default:
> > + debug("%s: Do not manage %d interface\n",
> > + __func__, interface_type);
> > + /* Do not manage others interfaces */
> > + return -EINVAL;
> > + }
> > +
> > + /* clear and set ETH configuration bits */
> > + writel(SYSCFG_PMCSETR_ETH_SEL_MASK |
> > SYSCFG_PMCSETR_ETH_SELMII |
> > + SYSCFG_PMCSETR_ETH_REF_CLK_SEL |
> > SYSCFG_PMCSETR_ETH_CLK_SEL,
> > + syscfg + SYSCFG_PMCCLRR);
> > + writel(value, syscfg + SYSCFG_PMCSETR);
> > +
> > + return 0;
> > +}
> > +
> > +enum env_location env_get_location(enum env_operation op, int prio) {
> > + if (prio)
> > + return ENVL_UNKNOWN;
> > +
> > +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
> > + return ENVL_SPI_FLASH;
> > +#else
> > + return ENVL_NOWHERE;
> > +#endif
> > +}
> > +
> > +#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
> > +
> > +#define MTDPARTS_LEN 256
> > +#define MTDIDS_LEN 128
> > +
> > +/**
> > + * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
> > + * If we need to access it before the env is relocated, then we need
> > + * to use our own stack buffer. gd->env_buf will be too small.
> > + *
> > + * @param buf temporary buffer pointer MTDPARTS_LEN long
> > + * @return mtdparts variable string, NULL if not found */ static
> > +const char *env_get_mtdparts(const char *str, char *buf) {
> > + if (gd->flags & GD_FLG_ENV_READY)
> > + return env_get(str);
> > + if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
> > + return buf;
> > +
> > + return NULL;
> > +}
> > +
> > +/**
> > + * update the variables "mtdids" and "mtdparts" with content of
> > +mtdparts_<dev> */ static void board_get_mtdparts(const char *dev,
> > + char *mtdids,
> > + char *mtdparts)
> > +{
> > + char env_name[32] = "mtdparts_";
> > + char tmp_mtdparts[MTDPARTS_LEN];
> > + const char *tmp;
> > +
> > + /* name of env variable to read = mtdparts_<dev> */
> > + strcat(env_name, dev);
> > + tmp = env_get_mtdparts(env_name, tmp_mtdparts);
> > + if (tmp) {
> > + /* mtdids: "<dev>=<dev>, ...." */
> > + if (mtdids[0] != '\0')
> > + strcat(mtdids, ",");
> > + strcat(mtdids, dev);
> > + strcat(mtdids, "=");
> > + strcat(mtdids, dev);
> > +
> > + /* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
> > + if (mtdparts[0] != '\0')
> > + strncat(mtdparts, ";", MTDPARTS_LEN);
> > + else
> > + strcat(mtdparts, "mtdparts=");
> > + strncat(mtdparts, dev, MTDPARTS_LEN);
> > + strncat(mtdparts, ":", MTDPARTS_LEN);
> > + strncat(mtdparts, tmp, MTDPARTS_LEN);
> > + }
> > +}
> > +
> > +void board_mtdparts_default(const char **mtdids, const char
> > +**mtdparts) {
> > + struct udevice *dev;
> > + static char parts[3 * MTDPARTS_LEN + 1];
> > + static char ids[MTDIDS_LEN + 1];
> > + static bool mtd_initialized;
> > +
> > + if (mtd_initialized) {
> > + *mtdids = ids;
> > + *mtdparts = parts;
> > + return;
> > + }
> > +
> > + memset(parts, 0, sizeof(parts));
> > + memset(ids, 0, sizeof(ids));
> > +
> > + /* probe all MTD devices */
> > + for (uclass_first_device(UCLASS_MTD, &dev);
> > + dev;
> > + uclass_next_device(&dev)) {
> > + pr_debug("mtd device = %s\n", dev->name);
> > + }
> > +
> > + if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> > + board_get_mtdparts("nor0", ids, parts);
> > +
> > + mtd_initialized = true;
> > + *mtdids = ids;
> > + *mtdparts = parts;
> > + debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); }
> > +#endif
> > +
> > +#if defined(CONFIG_OF_BOARD_SETUP)
> > +int ft_board_setup(void *blob, bd_t *bd) {
> > + return 0;
> > +}
> > +#endif
> > +
> > +#ifdef CONFIG_SET_DFU_ALT_INFO
> > +#define DFU_ALT_BUF_LEN SZ_1K
> > +
> > +static void board_get_alt_info(const char *dev, char *buff) {
> > + char var_name[32] = "dfu_alt_info_";
> > + int ret;
> > +
> > + ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
> > +
> > + /* name of env variable to read = dfu_alt_info_<dev> */
> > + strcat(var_name, dev);
> > + ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
> > + if (ret) {
> > + if (buff[0] != '\0')
> > + strcat(buff, "&");
> > + strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
> > + }
> > +}
> > +
> > +void set_dfu_alt_info(char *interface, char *devstr) {
> > + struct udevice *dev;
> > +
> > + ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
> > +
> > + if (env_get("dfu_alt_info"))
> > + return;
> > +
> > + memset(buf, 0, sizeof(buf));
> > +
> > + /* probe all MTD devices */
> > + mtd_probe_devices();
> > +
> > + board_get_alt_info("ram", buf);
> > +
> > + if (!uclass_get_device(UCLASS_MMC, 0, &dev))
> > + board_get_alt_info("mmc0", buf);
> > +
> > + if (!uclass_get_device(UCLASS_MMC, 1, &dev))
> > + board_get_alt_info("mmc1", buf);
> > +
> > + if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> > + board_get_alt_info("nor0", buf);
> > +
> > + env_set("dfu_alt_info", buf);
> > + puts("DFU alt info setting: done\n"); } #endif
> > +
> > +static void board_copro_image_process(ulong fw_image, size_t fw_size) {
> > + int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
> > +
> > + if (!rproc_is_initialized())
> > + if (rproc_init()) {
> > + printf("Remote Processor %d initialization failed\n",
> > + id);
> > + return;
> > + }
> > +
> > + ret = rproc_load(id, fw_image, fw_size);
> > + printf("Load Remote Processor %d with data at addr=0x%08lx %u
> > bytes:%s\n",
> > + id, fw_image, fw_size, ret ? " Failed!" : " Success!");
> > +
> > + if (!ret) {
> > + rproc_start(id);
> > + env_set("copro_state", "booted");
> > + }
> > +}
> > +
> > +U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,
> > board_copro_image_process);
> > diff --git a/configs/stm32mp15_dhcom_basic_defconfig
> > b/configs/stm32mp15_dhcom_basic_defconfig
> > new file mode 100644
> > index 0000000000..e4f331a913
> > --- /dev/null
> > +++ b/configs/stm32mp15_dhcom_basic_defconfig
> > @@ -0,0 +1,140 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_STM32MP=y
> > +CONFIG_SYS_MALLOC_F_LEN=0x3000
> > +CONFIG_SPL_MMC_SUPPORT=y
> > +CONFIG_ENV_SIZE=0x4000
> > +CONFIG_SPL=y
> > +CONFIG_TARGET_STM32MP1=y
> > +# CONFIG_TARGET_STM32MP157C_DK2 is not set
>
> CONFIG_TARGET_DH_STM32MP1_PDK2=y
>
> > +CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y #
> > +CONFIG_ARMV7_VIRT is not set
> > +CONFIG_SPL_TEXT_BASE=0x2FFC2500
> > +CONFIG_DISTRO_DEFAULTS=y
> > +CONFIG_FIT=y
> > +# CONFIG_BOOTSTAGE is not set
> > +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +CONFIG_SPL_MTD_SUPPORT=y
> > +CONFIG_SPL_POWER_SUPPORT=y
> > +CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
> > +CONFIG_SYS_PROMPT="STM32MP> "
> > +# CONFIG_CMD_BOOTD is not set
> > +# CONFIG_CMD_ELF is not set
> > +# CONFIG_CMD_IMI is not set
> > +# CONFIG_CMD_XIMG is not set
> > +# CONFIG_CMD_EXPORTENV is not set
> > +CONFIG_CMD_EEPROM=y
> > +CONFIG_CMD_MEMINFO=y
> > +CONFIG_CMD_MEMTEST=y
> > +CONFIG_CMD_ADC=y
> > +CONFIG_CMD_CLK=y
> > +CONFIG_CMD_DFU=y
> > +CONFIG_CMD_FUSE=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_GPT=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_MTD=y
> > +CONFIG_CMD_REMOTEPROC=y
> > +CONFIG_CMD_SPI=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_CMD_USB_MASS_STORAGE=y
> > +CONFIG_CMD_BMP=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_TIME=y
> > +CONFIG_CMD_TIMER=y
> > +CONFIG_CMD_PMIC=y
> > +CONFIG_CMD_REGULATOR=y
> > +CONFIG_CMD_EXT4_WRITE=y
> > +CONFIG_CMD_MTDPARTS=y
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
> > +CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-
> > extended interrupt-controller \\\#interrupt-cells interrupt-parent
> > dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-
> parents hwlocks"
> > +CONFIG_ENV_IS_IN_SPI_FLASH=y
> > +CONFIG_USE_ENV_SPI_BUS=y
> > +CONFIG_ENV_SPI_BUS=0
> > +CONFIG_USE_ENV_SPI_CS=y
> > +CONFIG_ENV_SPI_CS=0
> > +CONFIG_USE_ENV_SPI_MAX_HZ=y
> > +CONFIG_ENV_SPI_MAX_HZ=10000000
> > +CONFIG_USE_ENV_SPI_MODE=y
> > +CONFIG_ENV_SPI_MODE=0x0
> > +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> > +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> > +CONFIG_NET_RANDOM_ETHADDR=y
> > +CONFIG_IP_DEFRAG=y
> > +CONFIG_TFTP_BLOCKSIZE=1536
> > +CONFIG_STM32_ADC=y
> > +CONFIG_SPL_BLOCK_CACHE=y
> > +CONFIG_DFU_MMC=y
> > +CONFIG_DFU_RAM=y
> > +CONFIG_DFU_VIRT=y
> > +CONFIG_DM_HWSPINLOCK=y
> > +CONFIG_HWSPINLOCK_STM32=y
> > +CONFIG_DM_I2C=y
> > +CONFIG_SYS_I2C_STM32F7=y
> > +CONFIG_LED=y
> > +CONFIG_LED_GPIO=y
> > +CONFIG_DM_MAILBOX=y
> > +CONFIG_STM32_IPCC=y
> > +CONFIG_I2C_EEPROM=y
> > +CONFIG_DM_MMC=y
> > +CONFIG_SUPPORT_EMMC_BOOT=y
> > +CONFIG_STM32_SDMMC2=y
> > +CONFIG_MTD=y
> > +CONFIG_DM_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_MACRONIX=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_SPI_FLASH_WINBOND=y
> > +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> > CONFIG_SPI_FLASH_MTD=y
> > +CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y
> > CONFIG_DWC_ETH_QOS=y
> > +CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y
> #
> > +CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
> > +CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
> > +CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
> > +CONFIG_DM_REGULATOR_GPIO=y
> > CONFIG_DM_REGULATOR_STM32_VREFBUF=y
> > +CONFIG_DM_REGULATOR_STPMIC1=y
> > +CONFIG_REMOTEPROC_STM32_COPRO=y
> > +CONFIG_DM_RTC=y
> > +CONFIG_RTC_STM32=y
> > +CONFIG_SERIAL_RX_BUFFER=y
> > +CONFIG_SPI=y
> > +CONFIG_DM_SPI=y
> > +CONFIG_STM32_QSPI=y
> > +CONFIG_STM32_SPI=y
> > +CONFIG_USB=y
> > +CONFIG_DM_USB=y
> > +CONFIG_DM_USB_GADGET=y
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_USB_EHCI_GENERIC=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="dh"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x0483
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
> > +CONFIG_USB_GADGET_DWC2_OTG=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > +CONFIG_USB_HOST_ETHER=y
> > +CONFIG_USB_ETHER_ASIX=y
> > +CONFIG_DM_VIDEO=y
> > +CONFIG_BACKLIGHT_GPIO=y
> > +CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
> > +CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
> > +CONFIG_VIDEO_STM32=y
> > +CONFIG_VIDEO_STM32_DSI=y
> > +CONFIG_VIDEO_STM32_MAX_XRES=1280
> > +CONFIG_VIDEO_STM32_MAX_YRES=800
> > +CONFIG_LZO=y
> > +CONFIG_FDT_FIXUP_PARTITIONS=y
> > --
> > 2.24.1
> >
>
> Regards
>
> Patrick
More information about the U-Boot
mailing list