[PATCH v3 06/10] riscv: sifive: fu540: add SPL configuration

Anup Patel anup at brainfault.org
Sat Jan 25 09:35:44 CET 2020


On Fri, Jan 24, 2020 at 11:21 AM Pragnesh Patel
<pragnesh.patel at sifive.com> wrote:
>
> Add a support for SPL which will boot from L2 LIM (0x0800_0000) and
> then boot U-boot FIT image including OpenSBI FW_DYNAMIC firmware
> and U-Boot proper images from 1st partition of MMC boot devices.
>
> SPL related code is leverage from FSBL
> (https://github.com/sifive/freedom-u540-c000-bootloader.git)
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel at sifive.com>
> ---
>  board/sifive/fu540/Kconfig            |   8 +
>  board/sifive/fu540/Makefile           |   1 +
>  board/sifive/fu540/fu540-memory-map.h |  33 ++++
>  board/sifive/fu540/fu540.c            |  24 +++
>  board/sifive/fu540/spl.c              | 252 ++++++++++++++++++++++++++
>  board/sifive/fu540/ux00prci.h         |  56 ++++++
>  include/configs/sifive-fu540.h        |  18 ++
>  7 files changed, 392 insertions(+)
>  create mode 100644 board/sifive/fu540/fu540-memory-map.h
>  create mode 100644 board/sifive/fu540/spl.c
>  create mode 100644 board/sifive/fu540/ux00prci.h
>
> diff --git a/board/sifive/fu540/Kconfig b/board/sifive/fu540/Kconfig
> index 5ca21474de..edb224ed7a 100644
> --- a/board/sifive/fu540/Kconfig
> +++ b/board/sifive/fu540/Kconfig
> @@ -13,12 +13,20 @@ config SYS_CONFIG_NAME
>         default "sifive-fu540"
>
>  config SYS_TEXT_BASE
> +       default 0x80200000 if SPL
>         default 0x80000000 if !RISCV_SMODE
>         default 0x80200000 if RISCV_SMODE
>
> +config SPL_TEXT_BASE
> +       default 0x08000000
> +
> +config SPL_OPENSBI_LOAD_ADDR
> +       default 0x80000000
> +
>  config BOARD_SPECIFIC_OPTIONS # dummy
>         def_bool y
>         select GENERIC_RISCV
> +       select SUPPORT_SPL
>         imply CMD_DHCP
>         imply CMD_EXT2
>         imply CMD_EXT4
> diff --git a/board/sifive/fu540/Makefile b/board/sifive/fu540/Makefile
> index e4e76e1de3..cdcf894ade 100644
> --- a/board/sifive/fu540/Makefile
> +++ b/board/sifive/fu540/Makefile
> @@ -5,5 +5,6 @@
>  obj-y  += fu540.o
>
>  ifdef CONFIG_SPL_BUILD
> +obj-y += spl.o
>  obj-y += ddr.o
>  endif
> diff --git a/board/sifive/fu540/fu540-memory-map.h b/board/sifive/fu540/fu540-memory-map.h
> new file mode 100644
> index 0000000000..c65203726b
> --- /dev/null
> +++ b/board/sifive/fu540/fu540-memory-map.h
> @@ -0,0 +1,33 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (c) 2019 SiFive, Inc
> + */
> +
> +#ifndef FU540_MEMORY_MAP
> +#define FU540_MEMORY_MAP
> +
> +#include <asm/arch/gpio.h>
> +#include "ux00prci.h"
> +
> +/****************************************************************************
> + * Platform definitions
> + *****************************************************************************/
> +
> +/* Memory map */
> +#define GPIO_CTRL_ADDR                 _AC(0x10060000, UL)
> +
> +#define PHYSICAL_FILTER_CTRL_ADDR      _AC(0x100b8000, UL)
> +
> +#define UX00DDR_CTRL_ADDR              _AC(0x100b0000, UL)
> +#define UX00PRCI_CTRL_ADDR             _AC(0x10000000, UL)
> +
> +/* Helper functions */
> +#define _REG32(p, i)    (*(volatile uint32_t *)((p) + (i)))
> +
> +#define UX00PRCI_REG(offset)  \
> +       _REG32(UX00PRCI_CTRL_ADDR, \
> +                       offset)
> +
> +#define GPIO_REG(offset)      _REG32(GPIO_CTRL_ADDR, offset)
> +
> +#endif /* FU540_MEMORY_MAP */
> diff --git a/board/sifive/fu540/fu540.c b/board/sifive/fu540/fu540.c
> index 3a5e74f1fb..b81003aa6f 100644
> --- a/board/sifive/fu540/fu540.c
> +++ b/board/sifive/fu540/fu540.c
> @@ -11,6 +11,7 @@
>  #include <linux/delay.h>
>  #include <linux/io.h>
>  #include <misc.h>
> +#include <spl.h>
>
>  /*
>   * This define is a value used for error/unknown serial.
> @@ -114,3 +115,26 @@ int board_init(void)
>
>         return 0;
>  }
> +
> +#ifdef CONFIG_SPL
> +void board_boot_order(u32 *spl_boot_list)
> +{
> +       u8 i;
> +       u32 boot_devices[] = {
> +#ifdef CONFIG_SPL_MMC_SUPPORT
> +               BOOT_DEVICE_MMC1,
> +#endif
> +       };
> +
> +       for (i = 0; i < ARRAY_SIZE(boot_devices); i++)
> +               spl_boot_list[i] = boot_devices[i];
> +}
> +#endif
> +
> +#ifdef CONFIG_SPL_LOAD_FIT
> +int board_fit_config_name_match(const char *name)
> +{
> +       /* boot using first FIT config */
> +       return 0;
> +}
> +#endif
> diff --git a/board/sifive/fu540/spl.c b/board/sifive/fu540/spl.c
> new file mode 100644
> index 0000000000..c7ae4aa292
> --- /dev/null
> +++ b/board/sifive/fu540/spl.c
> @@ -0,0 +1,252 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (c) 2019 SiFive, Inc
> + */
> +
> +#include <common.h>
> +#include <spl.h>
> +#include <misc.h>
> +
> +#include "ux00ddr.h"
> +#include "fu540-memory-map.h"
> +
> +#define DDR_SIZE  (8UL * 1024UL * 1024UL * 1024UL)
> +#define DDRCTLPLL_F 55
> +#define DDRCTLPLL_Q 2
> +
> +#define PHY_NRESET 0x1000
> +
> +static inline int ux00prci_select_corepll(volatile u32 *coreclkselreg,
> +                                         volatile u32 *corepllcfg,
> +                                         volatile u32 *corepllout,
> +                                         u32 pllconfigval)
> +{
> +       (*corepllcfg) = pllconfigval;
> +
> +       // Wait for lock
> +       while (((*corepllcfg) & (PLL_LOCK(1))) == 0)
> +               ;
> +
> +       u32 core_out =
> +               (PLLOUT_DIV(PLLOUT_DIV_default)) |
> +               (PLLOUT_DIV_BY_1(PLLOUT_DIV_BY_1_default)) |
> +               (PLLOUT_CLK_EN(1));
> +       (*corepllout) = core_out;
> +
> +       // Set CORECLKSELREG to select COREPLL
> +       (*coreclkselreg) = PLL_CORECLKSEL_COREPLL;
> +
> +       return 0;
> +}
> +
> +static inline int ux00prci_select_corepll_500mhz(volatile u32 *coreclkselreg,
> +                                                volatile u32 *corepllcfg,
> +                                                volatile u32 *corepllout)
> +{
> +       /*
> +        * CORE pll init
> +        * Set corepll 33MHz -> 1GHz
> +        */
> +
> +       u32 core500mhz =
> +               (PLL_R(0)) |
> +               (PLL_F(59)) |            // 4000MHz VCO
> +               (PLL_Q(3)) |             /* /8 Output divider */
> +               (PLL_RANGE(0x4)) |
> +               (PLL_BYPASS(0)) |
> +               (PLL_FSE(1));
> +
> +       return ux00prci_select_corepll(coreclkselreg, corepllcfg, corepllout,
> +                       core500mhz);
> +}
> +
> +static inline int ux00prci_select_corepll_1ghz(volatile u32 *coreclkselreg,
> +                                              volatile u32 *corepllcfg,
> +                                              volatile u32 *corepllout)
> +{
> +       /*
> +        * CORE pll init
> +        * Set corepll 33MHz -> 1GHz
> +        */
> +
> +       u32 core1ghz =
> +               (PLL_R(0)) |
> +               (PLL_F(59)) |            // 4000MHz VCO
> +               (PLL_Q(2)) |             /* /4 Output divider */
> +               (PLL_RANGE(0x4)) |
> +               (PLL_BYPASS(0)) |
> +               (PLL_FSE(1));
> +
> +       return ux00prci_select_corepll(coreclkselreg, corepllcfg, corepllout,
> +                       core1ghz);
> +}
> +
> +long nsec_per_cyc = 300; // 33.333MHz
> +void nsleep(long nsec)
> +{
> +       long step = nsec_per_cyc * 2;
> +
> +       while (nsec > 0)
> +               nsec -= step;
> +}
> +
> +void init_clk_and_ddr(void)
> +{
> +       // PRCI init
> +
> +       // Check Reset Values (lock don't care)
> +       u32 pll_default =
> +               (PLL_R(PLL_R_default)) |
> +               (PLL_F(PLL_F_default)) |
> +               (PLL_Q(PLL_Q_default)) |
> +               (PLL_RANGE(PLL_RANGE_default)) |
> +               (PLL_BYPASS(PLL_BYPASS_default)) |
> +               (PLL_FSE(PLL_FSE_default));
> +       u32 lockmask = ~PLL_LOCK(1);
> +       u32 pllout_default =
> +               (PLLOUT_DIV(PLLOUT_DIV_default)) |
> +               (PLLOUT_DIV_BY_1(PLLOUT_DIV_BY_1_default)) |
> +               (PLLOUT_CLK_EN(PLLOUT_CLK_EN_default));
> +
> +       if ((UX00PRCI_REG(UX00PRCI_COREPLLCFG)     ^ pll_default) & lockmask)
> +               return;
> +       if ((UX00PRCI_REG(UX00PRCI_COREPLLOUT)     ^ pllout_default))
> +               return;
> +       if ((UX00PRCI_REG(UX00PRCI_DDRPLLCFG)      ^ pll_default) & lockmask)
> +               return;
> +       if ((UX00PRCI_REG(UX00PRCI_DDRPLLOUT)      ^ pllout_default))
> +               return;
> +       if (((UX00PRCI_REG(UX00PRCI_GEMGXLPLLCFG)) ^ pll_default) & lockmask)
> +               return;
> +       if (((UX00PRCI_REG(UX00PRCI_GEMGXLPLLOUT)) ^ pllout_default))
> +               return;
> +
> +       /* CORE pll init
> +        * If tlclksel is set for 2:1 operation,
> +        * Set corepll 33Mhz -> 1GHz
> +        * Otherwise, set corepll 33MHz -> 500MHz.
> +        */
> +
> +       if (UX00PRCI_REG(UX00PRCI_CLKMUXSTATUSREG) & CLKMUX_STATUS_TLCLKSEL) {
> +               ux00prci_select_corepll_500mhz
> +                       (&UX00PRCI_REG(UX00PRCI_CORECLKSELREG),
> +                        &UX00PRCI_REG(UX00PRCI_COREPLLCFG),
> +                        &UX00PRCI_REG(UX00PRCI_COREPLLOUT));
> +       } else {
> +               ux00prci_select_corepll_1ghz
> +                       (&UX00PRCI_REG(UX00PRCI_CORECLKSELREG),
> +                        &UX00PRCI_REG(UX00PRCI_COREPLLCFG),
> +                        &UX00PRCI_REG(UX00PRCI_COREPLLOUT));
> +       }
> +
> +       //DDR init
> +       u32 ddrctlmhz =
> +               (PLL_R(0)) |
> +               (PLL_F(DDRCTLPLL_F)) |
> +               (PLL_Q(DDRCTLPLL_Q)) |
> +               (PLL_RANGE(0x4)) |
> +               (PLL_BYPASS(0)) |
> +               (PLL_FSE(1));
> +       UX00PRCI_REG(UX00PRCI_DDRPLLCFG) = ddrctlmhz;
> +
> +       // Wait for lock
> +       while ((UX00PRCI_REG(UX00PRCI_DDRPLLCFG) & PLL_LOCK(1)) == 0)
> +               ;
> +
> +       u32 ddrctl_out =
> +               (PLLOUT_DIV(PLLOUT_DIV_default)) |
> +               (PLLOUT_DIV_BY_1(PLLOUT_DIV_BY_1_default)) |
> +               (PLLOUT_CLK_EN(1));
> +       (UX00PRCI_REG(UX00PRCI_DDRPLLOUT)) = ddrctl_out;
> +
> +       //Release DDR reset.
> +       UX00PRCI_REG(UX00PRCI_DEVICESRESETREG) |=
> +               DEVICESRESET_DDR_CTRL_RST_N(1);
> +
> +       // HACK to get the '1 full controller clock cycle'.
> +       asm volatile ("fence");
> +       UX00PRCI_REG(UX00PRCI_DEVICESRESETREG) |= DEVICESRESET_DDR_AXI_RST_N(1)
> +               | DEVICESRESET_DDR_AHB_RST_N(1) | DEVICESRESET_DDR_PHY_RST_N(1);
> +       // HACK to get the '1 full controller clock cycle'.
> +       asm volatile ("fence");
> +
> +       /* These take like 16 cycles to actually propagate. We can't go sending
> +        * stuff before they come out of reset. So wait. (TODO: Add a register
> +        * to read the current reset states, or DDR Control device?)
> +        */
> +       for (int i = 0; i < 256; i++)
> +               asm volatile ("nop");
> +
> +       ux00ddr_writeregmap(UX00DDR_CTRL_ADDR, ddr_ctl_settings,
> +                           ddr_phy_settings);
> +       ux00ddr_disableaxireadinterleave(UX00DDR_CTRL_ADDR);
> +
> +       ux00ddr_disableoptimalrmodw(UX00DDR_CTRL_ADDR);
> +
> +       ux00ddr_enablewriteleveling(UX00DDR_CTRL_ADDR);
> +       ux00ddr_enablereadleveling(UX00DDR_CTRL_ADDR);
> +       ux00ddr_enablereadlevelinggate(UX00DDR_CTRL_ADDR);
> +       if (ux00ddr_getdramclass(UX00DDR_CTRL_ADDR) == DRAM_CLASS_DDR4)
> +               ux00ddr_enablevreftraining(UX00DDR_CTRL_ADDR);
> +       //mask off interrupts for leveling completion
> +       ux00ddr_mask_leveling_completed_interrupt(UX00DDR_CTRL_ADDR);
> +
> +       ux00ddr_mask_mc_init_complete_interrupt(UX00DDR_CTRL_ADDR);
> +       ux00ddr_mask_outofrange_interrupts(UX00DDR_CTRL_ADDR);
> +       ux00ddr_setuprangeprotection(UX00DDR_CTRL_ADDR, DDR_SIZE);
> +       ux00ddr_mask_port_command_error_interrupt(UX00DDR_CTRL_ADDR);
> +
> +       const u64 ddr_size = DDR_SIZE;
> +       const u64 ddr_end = CONFIG_SYS_SDRAM_BASE + ddr_size;
> +
> +       ux00ddr_start(UX00DDR_CTRL_ADDR, PHYSICAL_FILTER_CTRL_ADDR, ddr_end);
> +       ux00ddr_phy_fixup(UX00DDR_CTRL_ADDR);
> +
> +       //GEMGXL init
> +       u32 gemgxl125mhz =
> +               (PLL_R(0)) |
> +               (PLL_F(59)) |  //4000Mhz VCO
> +               (PLL_Q(5)) |   /* /32 */
> +               (PLL_RANGE(0x4)) |
> +               (PLL_BYPASS(0)) |
> +               (PLL_FSE(1));
> +       UX00PRCI_REG(UX00PRCI_GEMGXLPLLCFG) = gemgxl125mhz;
> +
> +       // Wait for lock
> +       while ((UX00PRCI_REG(UX00PRCI_GEMGXLPLLCFG) & PLL_LOCK(1)) == 0)
> +               ;
> +
> +       u32 gemgxlctl_out =
> +               (PLLOUT_DIV(PLLOUT_DIV_default)) |
> +               (PLLOUT_DIV_BY_1(PLLOUT_DIV_BY_1_default)) |
> +               (PLLOUT_CLK_EN(1));
> +       UX00PRCI_REG(UX00PRCI_GEMGXLPLLOUT) = gemgxlctl_out;
> +
> +       //Release GEMGXL reset (set bit DEVICESRESET_GEMGXL to 1)
> +       UX00PRCI_REG(UX00PRCI_DEVICESRESETREG) |= DEVICESRESET_GEMGXL_RST_N(1);
> +
> +       // VSC8541 PHY reset sequence; leave pull-down active for 2ms
> +       nsleep(2000000);
> +       // Set GPIO 12 (PHY NRESET) to OE=1 and OVAL=1
> +       GPIO_REG(GPIO_OUTPUT_VAL) |= PHY_NRESET;
> +       GPIO_REG(GPIO_OUTPUT_EN) |= PHY_NRESET;
> +       nsleep(100);
> +
> +       // Procmon => core clock
> +       UX00PRCI_REG(UX00PRCI_PROCMONCFG) = 0x1 << 24;
> +}
> +
> +void board_init_f(ulong dummy)
> +{
> +       int ret;
> +
> +       ret = spl_early_init();
> +       if (ret)
> +               panic("spl_early_init() failed: %d\n", ret);
> +
> +       arch_cpu_init_dm();
> +
> +       init_clk_and_ddr();
> +
> +       preloader_console_init();
> +}
> diff --git a/board/sifive/fu540/ux00prci.h b/board/sifive/fu540/ux00prci.h
> new file mode 100644
> index 0000000000..90ca3cd258
> --- /dev/null
> +++ b/board/sifive/fu540/ux00prci.h
> @@ -0,0 +1,56 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (c) 2019 SiFive, Inc
> + */
> +
> +#ifndef _SIFIVE_UX00PRCI_H
> +#define _SIFIVE_UX00PRCI_H
> +
> +/* Register offsets */
> +#define UX00PRCI_HFROSCCFG          (0x0000)
> +#define UX00PRCI_COREPLLCFG         (0x0004)
> +#define UX00PRCI_COREPLLOUT         (0x0008)
> +#define UX00PRCI_DDRPLLCFG          (0x000C)
> +#define UX00PRCI_DDRPLLOUT          (0x0010)
> +#define UX00PRCI_GEMGXLPLLCFG       (0x001C)
> +#define UX00PRCI_GEMGXLPLLOUT       (0x0020)
> +#define UX00PRCI_CORECLKSELREG      (0x0024)
> +#define UX00PRCI_DEVICESRESETREG    (0x0028)
> +#define UX00PRCI_CLKMUXSTATUSREG    (0x002C)
> +#define UX00PRCI_PROCMONCFG         (0x00F0)
> +
> +#define PLL_R(x)              (((x) & 0x3F) << 0)
> +#define PLL_F(x)              (((x) & 0x1FF) << 6)
> +#define PLL_Q(x)              (((x) & 0x7) << 15)
> +#define PLL_RANGE(x)          (((x) & 0x7) << 18)
> +#define PLL_BYPASS(x)         (((x) & 0x1) << 24)
> +#define PLL_FSE(x)            (((x) & 0x1) << 25)
> +#define PLL_LOCK(x)           (((x) & 0x1) << 31)
> +
> +#define PLLOUT_DIV(x)         (((x) & 0x7F) << 0)
> +#define PLLOUT_DIV_BY_1(x)    (((x) & 0x1) << 8)
> +#define PLLOUT_CLK_EN(x)      (((x) & 0x1) << 31)
> +
> +#define PLL_R_default              0x1
> +#define PLL_F_default              0x1F
> +#define PLL_Q_default              0x3
> +#define PLL_RANGE_default          0x0
> +#define PLL_BYPASS_default         0x1
> +#define PLL_FSE_default            0x1
> +
> +#define PLLOUT_DIV_default         0x0
> +#define PLLOUT_DIV_BY_1_default    0x0
> +#define PLLOUT_CLK_EN_default      0x0
> +
> +#define PLL_CORECLKSEL_HFXIN       0x1
> +#define PLL_CORECLKSEL_COREPLL     0x0
> +
> +#define DEVICESRESET_DDR_CTRL_RST_N(x)    (((x) & 0x1) << 0)
> +#define DEVICESRESET_DDR_AXI_RST_N(x)     (((x) & 0x1) << 1)
> +#define DEVICESRESET_DDR_AHB_RST_N(x)     (((x) & 0x1) << 2)
> +#define DEVICESRESET_DDR_PHY_RST_N(x)     (((x) & 0x1) << 3)
> +#define DEVICESRESET_GEMGXL_RST_N(x)      (((x) & 0x1) << 5)
> +
> +#define CLKMUX_STATUS_TLCLKSEL         (0x1 << 1)
> +
> +#endif // _SIFIVE_UX00PRCI_H
> diff --git a/include/configs/sifive-fu540.h b/include/configs/sifive-fu540.h
> index 2756ed5a77..ef3ae9b650 100644
> --- a/include/configs/sifive-fu540.h
> +++ b/include/configs/sifive-fu540.h
> @@ -11,6 +11,22 @@
>
>  #include <linux/sizes.h>
>
> +#ifdef CONFIG_SPL
> +
> +#define CONFIG_SPL_MAX_SIZE            0x00100000
> +#define CONFIG_SPL_BSS_START_ADDR      0x85000000
> +#define CONFIG_SPL_BSS_MAX_SIZE                0x00100000
> +#define CONFIG_SYS_SPL_MALLOC_START    (CONFIG_SPL_BSS_START_ADDR + \
> +                                        CONFIG_SPL_BSS_MAX_SIZE)
> +#define CONFIG_SYS_SPL_MALLOC_SIZE     0x00100000
> +
> +#define CONFIG_SPL_LOAD_FIT_ADDRESS    0x84000000
> +
> +#define CONFIG_SPL_STACK       (0x08000000 + 0x001D0000 - \
> +                                GENERATED_GBL_DATA_SIZE)
> +
> +#endif
> +
>  #define CONFIG_SYS_SDRAM_BASE          0x80000000
>  #define CONFIG_SYS_INIT_SP_ADDR                (CONFIG_SYS_SDRAM_BASE + SZ_2M)
>
> @@ -24,6 +40,7 @@
>
>  /* Environment options */
>
> +#ifndef CONFIG_SPL_BUILD
>  #define BOOT_TARGET_DEVICES(func) \
>         func(MMC, mmc, 0) \
>         func(DHCP, dhcp, na)
> @@ -43,5 +60,6 @@
>  #define CONFIG_PREBOOT \
>         "setenv fdt_addr ${fdtcontroladdr};" \
>         "fdt addr ${fdtcontroladdr};"
> +#endif
>
>  #endif /* __CONFIG_H */
> --
> 2.17.1
>

LGTM.

Reviewed-by: Anup Patel <anup.patel at wdc.com>

Regards,
Anup


More information about the U-Boot mailing list