[PATCH v2] ARM: dts: stm32: add seeed studio odyssey-stm32mp157c board
Patrick DELAUNAY
patrick.delaunay at st.com
Wed Jul 1 13:02:34 CEST 2020
Hi,
> From: Patrick DELAUNAY
> Sent: mercredi 1 juillet 2020 11:59
>
> Hi Marcin,
>
> > From: Marcin Sloniewski <marcin.sloniewski at gmail.com>
> > Sent: mardi 30 juin 2020 22:02
> >
> > This commit adds device tree files supporting SBC from Seeed Studio
> > based on STM32MP157C.
> >
> > This works with generic stm32mp1 config.
> > Right now only booting from SD card is supported.
> >
> > Signed-off-by: Marcin Sloniewski <marcin.sloniewski at gmail.com>
> > ---
> >
> > Changes in v2:
> > - removed `st,adc_usb_pd` from config since that
> > adc connection is non-existent which caused
> > warning or hang during boot
> >
> > arch/arm/dts/Makefile | 3 +-
> > .../dts/odyssey-stm32mp157c-som-u-boot.dtsi | 134 +++++++
> > arch/arm/dts/odyssey-stm32mp157c-som.dtsi | 364 ++++++++++++++++++
> > arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi | 64 +++
> > arch/arm/dts/odyssey-stm32mp157c.dts | 161 ++++++++
> > 5 files changed, 725 insertions(+), 1 deletion(-) create mode 100644
> > arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi
> > create mode 100644 arch/arm/dts/odyssey-stm32mp157c-som.dtsi
> > create mode 100644 arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
> > create mode 100644 arch/arm/dts/odyssey-stm32mp157c.dts
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> > 9900b44274..dd617c7188 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -918,7 +918,8 @@ dtb-$(CONFIG_STM32MP15x) += \
> > stm32mp157c-ed1.dtb \
> > stm32mp157c-ev1.dtb \
> > stm32mp15xx-dhcom-pdk2.dtb \
> > - stm32mp15xx-dhcor-avenger96.dtb
> > + stm32mp15xx-dhcor-avenger96.dtb \
> > + odyssey-stm32mp157c.dtb
>
> Minor remarks, I try to follow alphabetics order when it is possible, so :
>
> dtb-$(CONFIG_STM32MP15x) += \
> + odyssey-stm32mp157c.dtb \
> stm32mp157a-dk1.dtb \
>
>
> > dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-
> base-
> > board.dtb
> > dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \ diff
> > --git a/arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi
> > b/arch/arm/dts/odyssey- stm32mp157c-som-u-boot.dtsi new file mode
> > 100644 index 0000000000..cf08efae09
> > --- /dev/null
> > +++ b/arch/arm/dts/odyssey-stm32mp157c-som-u-boot.dtsi
> > @@ -0,0 +1,134 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
> > +*/
> > +
> > +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> > +#include "stm32mp15-u-boot.dtsi"
> > +#include "stm32mp15-ddr3-1x4Gb-1066-binG.dtsi"
> > +
> > +/ {
> > + config {
> > + u-boot,boot-led = "heartbeat";
> > + };
> > +};
> > +
> > +&clk_hse {
> > + st,digbypass;
> > +};
> > +
> > +&i2c2 {
> > + u-boot,dm-pre-reloc;
> > +};
> > +
> > +&i2c2_pins_a {
> > + u-boot,dm-pre-reloc;
> > + pins {
> > + u-boot,dm-pre-reloc;
> > + };
> > +};
> > +
> > +&pmic {
> > + u-boot,dm-pre-reloc;
> > +};
> > +
> > +&rcc {
> > + st,clksrc = <
> > + CLK_MPU_PLL1P
> > + CLK_AXI_PLL2P
> > + CLK_MCU_PLL3P
> > + CLK_PLL12_HSE
> > + CLK_PLL3_HSE
> > + CLK_PLL4_HSE
> > + CLK_RTC_LSE
> > + CLK_MCO1_DISABLED
> > + CLK_MCO2_DISABLED
> > + >;
> > +
> > + st,clkdiv = <
> > + 1 /*MPU*/
> > + 0 /*AXI*/
> > + 0 /*MCU*/
> > + 1 /*APB1*/
> > + 1 /*APB2*/
> > + 1 /*APB3*/
> > + 1 /*APB4*/
> > + 2 /*APB5*/
> > + 23 /*RTC*/
> > + 0 /*MCO1*/
> > + 0 /*MCO2*/
> > + >;
> > +
> > + st,pkcs = <
> > + CLK_CKPER_HSE
> > + CLK_FMC_ACLK
> > + CLK_QSPI_ACLK
> > + CLK_ETH_DISABLED
> > + CLK_SDMMC12_PLL4P
> > + CLK_DSI_DSIPLL
> > + CLK_STGEN_HSE
> > + CLK_USBPHY_HSE
> > + CLK_SPI2S1_PLL3Q
> > + CLK_SPI2S23_PLL3Q
> > + CLK_SPI45_HSI
> > + CLK_SPI6_HSI
> > + CLK_I2C46_HSI
> > + CLK_SDMMC3_PLL4P
> > + CLK_USBO_USBPHY
> > + CLK_ADC_CKPER
> > + CLK_CEC_LSE
> > + CLK_I2C12_HSI
> > + CLK_I2C35_HSI
> > + CLK_UART1_HSI
> > + CLK_UART24_HSI
> > + CLK_UART35_HSI
> > + CLK_UART6_HSI
> > + CLK_UART78_HSI
> > + CLK_SPDIF_PLL4P
> > + CLK_FDCAN_PLL4R
> > + CLK_SAI1_PLL3Q
> > + CLK_SAI2_PLL3Q
> > + CLK_SAI3_PLL3Q
> > + CLK_SAI4_PLL3Q
> > + CLK_RNG1_LSI
> > + CLK_RNG2_LSI
> > + CLK_LPTIM1_PCLK1
> > + CLK_LPTIM23_PCLK3
> > + CLK_LPTIM45_LSE
> > + >;
> > +
> > + /* VCO = 1300.0 MHz => P = 650 (CPU) */
> > + pll1: st,pll at 0 {
> > + compatible = "st,stm32mp1-pll";
> > + reg = <0>;
> > + cfg = < 2 80 0 0 0 PQR(1,0,0) >;
> > + frac = < 0x800 >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +
>
> For information pll1 configuration will be comes optional with
> http://patchwork.ozlabs.org/project/uboot/list/?series=179056
>
> > + /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
> > + pll2: st,pll at 1 {
> > + compatible = "st,stm32mp1-pll";
> > + reg = <1>;
> > + cfg = < 2 65 1 0 0 PQR(1,1,1) >;
> > + frac = < 0x1400 >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +
> > + /* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
> > + pll3: st,pll at 2 {
> > + compatible = "st,stm32mp1-pll";
> > + reg = <2>;
> > + cfg = < 1 33 1 16 36 PQR(1,1,1) >;
> > + frac = < 0x1a04 >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +
> > + /* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
> > + pll4: st,pll at 3 {
> > + compatible = "st,stm32mp1-pll";
> > + reg = <3>;
> > + cfg = < 3 98 5 7 7 PQR(1,1,1) >;
> > + u-boot,dm-pre-reloc;
> > + };
> > +};
> > diff --git a/arch/arm/dts/odyssey-stm32mp157c-som.dtsi
> > b/arch/arm/dts/odyssey- stm32mp157c-som.dtsi new file mode 100644
> > index 0000000000..855de9523c
> > --- /dev/null
> > +++ b/arch/arm/dts/odyssey-stm32mp157c-som.dtsi
> > @@ -0,0 +1,364 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
> > +*/
> > +
> > +/dts-v1/;
> > +
> > +#include "stm32mp157.dtsi"
> > +#include "stm32mp15xc.dtsi"
> > +#include "stm32mp15-pinctrl.dtsi"
> > +#include "stm32mp15xxac-pinctrl.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/mfd/st,stpmic1.h>
> > +
> > +/ {
> > +
> > + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> > + compatible = "seeed,odyssey-stm32mp157c-som", "st,stm32mp157";
> > +
> > + memory at c0000000 {
> > + device_type = "memory";
> > + reg = <0xc0000000 0x20000000>;
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > +
> > + mcuram2: mcuram2 at 10000000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10000000 0x40000>;
> > + no-map;
> > + };
> > +
> > + vdev0vring0: vdev0vring0 at 10040000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10040000 0x1000>;
> > + no-map;
> > + };
> > +
> > + vdev0vring1: vdev0vring1 at 10041000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10041000 0x1000>;
> > + no-map;
> > + };
> > +
> > + vdev0buffer: vdev0buffer at 10042000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x10042000 0x4000>;
> > + no-map;
> > + };
> > +
> > + mcuram: mcuram at 30000000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x30000000 0x40000>;
> > + no-map;
> > + };
> > +
> > + retram: retram at 38000000 {
> > + compatible = "shared-dma-pool";
> > + reg = <0x38000000 0x10000>;
> > + no-map;
> > + };
> > +
> > + gpu_reserved: gpu at d4000000 {
> > + reg = <0xd4000000 0x4000000>;
> > + no-map;
> > + };
> > +
> > + optee at de000000 {
> > + reg = <0xde000000 0x02000000>;
> > + no-map;
> > + };
> > + };
> > +
> > + led {
> > + compatible = "gpio-leds";
> > + blue {
> > + label = "heartbeat";
> > + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + default-state = "off";
> > + };
> > + };
> > +
> > +};
> > +
> > +&gpu {
> > + contiguous-area = <&gpu_reserved>;
> > + status = "okay";
> > +};
> > +
> > +&i2c2 {
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&i2c2_pins_a>;
> > + pinctrl-1 = <&i2c2_pins_sleep_a>;
> > + i2c-scl-rising-time-ns = <185>;
> > + i2c-scl-falling-time-ns = <20>;
> > + clock-frequency = <400000>;
> > + status = "okay";
> > + /* spare dmas for other usage */
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > +
> > + pmic: stpmic at 33 {
> > + compatible = "st,stpmic1";
> > + reg = <0x33>;
> > + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> > + interrupt-controller;
> > + #interrupt-cells = <2>;
> > + status = "okay";
> > +
> > + regulators {
> > + compatible = "st,stpmic1-regulators";
> > + ldo1-supply = <&v3v3>;
> > + ldo3-supply = <&vdd_ddr>;
> > + ldo6-supply = <&v3v3>;
> > + pwr_sw1-supply = <&bst_out>;
> > + pwr_sw2-supply = <&bst_out>;
> > +
> > + vddcore: buck1 {
> > + regulator-name = "vddcore";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-always-on;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd_ddr: buck2 {
> > + regulator-name = "vdd_ddr";
> > + regulator-min-microvolt = <1350000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-always-on;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd: buck3 {
> > + regulator-name = "vdd";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + st,mask-reset;
> > + regulator-initial-mode = <0>;
> > + regulator-over-current-protection;
> > + };
> > +
> > + v3v3: buck4 {
> > + regulator-name = "v3v3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + regulator-initial-mode = <0>;
> > + };
> > +
> > + v1v8_audio: ldo1 {
> > + regulator-name = "v1v8_audio";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + interrupts = <IT_CURLIM_LDO1 0>;
> > + };
> > +
> > + v3v3_hdmi: ldo2 {
> > + regulator-name = "v3v3_hdmi";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + interrupts = <IT_CURLIM_LDO2 0>;
> > + };
> > +
> > + vtt_ddr: ldo3 {
> > + regulator-name = "vtt_ddr";
> > + regulator-min-microvolt = <500000>;
> > + regulator-max-microvolt = <750000>;
> > + regulator-always-on;
> > + regulator-over-current-protection;
> > + };
> > +
> > + vdd_usb: ldo4 {
> > + regulator-name = "vdd_usb";
> > + interrupts = <IT_CURLIM_LDO4 0>;
> > + };
> > +
> > + vdda: ldo5 {
> > + regulator-name = "vdda";
> > + regulator-min-microvolt = <2900000>;
> > + regulator-max-microvolt = <2900000>;
> > + interrupts = <IT_CURLIM_LDO5 0>;
> > + regulator-boot-on;
> > + };
> > +
> > + v1v2_hdmi: ldo6 {
> > + regulator-name = "v1v2_hdmi";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-always-on;
> > + interrupts = <IT_CURLIM_LDO6 0>;
> > + };
> > +
> > + vref_ddr: vref_ddr {
> > + regulator-name = "vref_ddr";
> > + regulator-always-on;
> > + };
> > +
> > + bst_out: boost {
> > + regulator-name = "bst_out";
> > + interrupts = <IT_OCP_BOOST 0>;
> > + };
> > +
> > + vbus_otg: pwr_sw1 {
> > + regulator-name = "vbus_otg";
> > + interrupts = <IT_OCP_OTG 0>;
> > + };
> > +
> > + vbus_sw: pwr_sw2 {
> > + regulator-name = "vbus_sw";
> > + interrupts = <IT_OCP_SWOUT 0>;
> > + regulator-active-discharge = <1>;
> > + };
> > + };
> > +
> > + onkey {
> > + compatible = "st,stpmic1-onkey";
> > + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> > + interrupt-names = "onkey-falling", "onkey-rising";
> > + power-off-time-sec = <10>;
> > + status = "okay";
> > + };
> > +
> > + watchdog {
> > + compatible = "st,stpmic1-wdt";
> > + status = "disabled";
> > + };
> > + };
> > +};
> > +
> > +&ipcc {
> > + status = "okay";
> > +};
> > +
> > +&iwdg2 {
> > + timeout-sec = <32>;
> > + status = "okay";
> > +};
> > +
> > +&m4_rproc {
> > + memory-region = <&retram>, <&mcuram>, <&mcuram2>,
> > <&vdev0vring0>,
> > + <&vdev0vring1>, <&vdev0buffer>;
> > + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> > + mbox-names = "vq0", "vq1", "shutdown";
> > + interrupt-parent = <&exti>;
> > + interrupts = <68 1>;
> > + status = "okay";
> > +};
> > +
> > +&sdmmc2 {
> > + pinctrl-names = "default", "opendrain", "sleep";
> > + pinctrl-0 = <&sdmmc2_b4_pins_a>;
> > + pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
> > + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
> > + broken-cd;
> > + disable-wp;
> > + st,neg-edge;
> > + bus-width = <4>;
> > + vmmc-supply = <&v3v3>;
> > + status = "okay";
> > +};
> > +
> > +&timers1 {
> > + /* spare dmas for other usage */
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm1_pins_a>;
> > + pinctrl-1 = <&pwm1_sleep_pins_a>;
> > + pinctrl-names = "default", "sleep";
> > + status = "okay";
> > + };
> > + timer at 0 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers3 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm3_pins_a>;
> > + pinctrl-1 = <&pwm3_sleep_pins_a>;
> > + pinctrl-names = "default", "sleep";
> > + status = "okay";
> > + };
> > + timer at 2 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers4 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>;
> > + pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>;
> > + pinctrl-names = "default", "sleep";
> > + status = "okay";
> > + };
> > + timer at 3 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers5 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm5_pins_a>;
> > + pinctrl-1 = <&pwm5_sleep_pins_a>;
> > + pinctrl-names = "default", "sleep";
> > + status = "okay";
> > + };
> > + timer at 4 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers6 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + timer at 5 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&timers12 {
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > + status = "disabled";
> > + pwm {
> > + pinctrl-0 = <&pwm12_pins_a>;
> > + pinctrl-1 = <&pwm12_sleep_pins_a>;
> > + pinctrl-names = "default", "sleep";
> > + status = "okay";
> > + };
> > + timer at 11 {
> > + status = "okay";
> > + };
> > +};
> > +
> > +&vrefbuf {
> > + regulator-min-microvolt = <2500000>;
> > + regulator-max-microvolt = <2500000>;
> > + vdda-supply = <&vdd>;
> > + status = "okay";
> > +};
> > diff --git a/arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
> > b/arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
> > new file mode 100644
> > index 0000000000..12073b3616
> > --- /dev/null
> > +++ b/arch/arm/dts/odyssey-stm32mp157c-u-boot.dtsi
> > @@ -0,0 +1,64 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
> > +*/
> > +
> > + #include "odyssey-stm32mp157c-som-u-boot.dtsi"
> > +
> > +/ {
> > + aliases {
> > + mmc0 = &sdmmc1;
> > + usb0 = &usbotg_hs;
> > + };
> > + config {
> > + u-boot,boot-led = "heartbeat";
> > + u-boot,error-led = "error";
> > + };
> > + led {
> > + red {
> > + label = "error";
> > + gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> > + default-state = "off";
> > + status = "okay";
> > + };
> > + };
> > +};
> > +
> > +&adc {
> > + status = "okay";
> > +};
> > +
> > +&sdmmc1 {
> > + u-boot,dm-spl;
> > +};
> > +
> > +&sdmmc1_b4_pins_a {
> > + u-boot,dm-spl;
> > + pins1 {
> > + u-boot,dm-spl;
> > + };
> > + pins2 {
> > + u-boot,dm-spl;
> > + };
> > +};
> > +
> > +&uart4 {
> > + u-boot,dm-pre-reloc;
> > +};
> > +
> > +&uart4_pins_a {
> > + u-boot,dm-pre-reloc;
> > + pins1 {
> > + u-boot,dm-pre-reloc;
> > + };
> > + pins2 {
> > + u-boot,dm-pre-reloc;
> > + /* pull-up on rx to avoid floating level */
> > + bias-pull-up;
> > + };
> > +};
> > +
> > +&usbotg_hs {
> > + u-boot,force-b-session-valid;
> > + hnp-srp-disable;
> > +};
>
> I think this part can be removed
> u-boot,force-b-session-valid => activated to force peripheral mode, used in
> DK1/DK2 only because we are using USB TypeC controller STUSB1600 for USB
> cable detection hnp-srp-disable => activated to avoid issue in HOST mode, and
> USTOTG is configured in PERIPHERAL after.
>
> > diff --git a/arch/arm/dts/odyssey-stm32mp157c.dts
> > b/arch/arm/dts/odyssey- stm32mp157c.dts new file mode 100644 index
> > 0000000000..949081ca84
> > --- /dev/null
> > +++ b/arch/arm/dts/odyssey-stm32mp157c.dts
> > @@ -0,0 +1,161 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniewski at gmail.com>
> > +*/
> > +
> > +/dts-v1/;
> > +
> > +#include "odyssey-stm32mp157c-som.dtsi"
> > +
> > +/ {
> > +
> > + model = "Seeed Studio Odyssey-STM32MP157C Board";
> > + compatible = "seeed,odyssey-stm32mp157c", "st,stm32mp157";
> > +
> > + aliases {
> > + ethernet0 = ðernet0;
> > + serial0 = &uart4;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + led {
> > + compatible = "gpio-leds";
> > + blue {
> > + label = "heartbeat";
> > + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + default-state = "off";
> > + };
> > + };
> > +
> > +};
> > +
> > +&adc {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&adc12_ain_pins_a>, <&adc12_usb_cc_pins_a>;
> > + vdd-supply = <&vdd>;
> > + vdda-supply = <&vdd>;
> > + vref-supply = <&vrefbuf>;
> > + status = "disabled";
> > + adc1: adc at 0 {
> > + /*
> > + * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19.
> > + * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C:
> > + * 5 * (56 + 47kOhms) * 5pF => 2.5us.
> > + * Use arbitrary margin here (e.g. 5us).
> > + */
> > + st,min-sample-time-nsecs = <5000>;
> > + /* AIN connector, USB Type-C CC1 & CC2 */
> > + st,adc-channels = <0 1 6 13 18 19>;
> > + status = "okay";
> > + };
> > + adc2: adc at 100 {
> > + /* AIN connector, USB Type-C CC1 & CC2 */
> > + st,adc-channels = <0 1 2 6 18 19>;
> > + st,min-sample-time-nsecs = <5000>;
> > + status = "okay";
> > + };
> > +};
> > +
> > +&cec {
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&cec_pins_b>;
> > + pinctrl-1 = <&cec_pins_sleep_b>;
> > + status = "okay";
> > +};
> > +
> > +ðernet0 {
> > + status = "okay";
> > + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> > + pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
> > + pinctrl-names = "default", "sleep";
> > + phy-mode = "rgmii-id";
> > + max-speed = <1000>;
> > + phy-handle = <&phy0>;
> > +
> > + mdio0 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + compatible = "snps,dwmac-mdio";
> > + phy0: ethernet-phy at 0 {
> > + reg = <0>;
> > + };
> > + };
> > +};
> > +
> > +&gpu {
> > + contiguous-area = <&gpu_reserved>;
> > + status = "okay";
> > +};
> > +
> > +&i2c1 {
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&i2c1_pins_a>;
> > + pinctrl-1 = <&i2c1_pins_sleep_a>;
> > + i2c-scl-rising-time-ns = <100>;
> > + i2c-scl-falling-time-ns = <7>;
> > + status = "okay";
> > + /delete-property/dmas;
> > + /delete-property/dma-names;
> > +};
> > +
> > +&i2s2 {
> > + clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
> > + clock-names = "pclk", "i2sclk", "x8k", "x11k";
> > + pinctrl-names = "default", "sleep";
> > + pinctrl-0 = <&i2s2_pins_a>;
> > + pinctrl-1 = <&i2s2_pins_sleep_a>;
> > + status = "okay";
> > +};
> > +
> > +&pwr_regulators {
> > + vdd-supply = <&vdd>;
> > + vdd_3v3_usbfs-supply = <&vdd_usb>;
> > +};
> > +
> > +&sdmmc1 {
> > + pinctrl-names = "default", "opendrain", "sleep";
> > + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> > + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> > + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> > + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> > + disable-wp;
> > + st,neg-edge;
> > + bus-width = <4>;
> > + vmmc-supply = <&v3v3>;
> > + status = "okay";
> > +};
> > +
> > +&uart4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart4_pins_a>;
> > + status = "okay";
> > +};
> > +
> > +&usbh_ehci {
> > + phys = <&usbphyc_port0>;
> > + status = "okay";
> > +};
> > +
> > +&usbotg_hs {
> > + dr_mode = "peripheral";
> > + phys = <&usbphyc_port1 0>;
> > + phy-names = "usb2-phy";
> > + status = "okay";
> > +};
> > +
> > +&usbphyc {
> > + status = "okay";
> > +};
> > +
> > +&usbphyc_port0 {
> > + phy-supply = <&vdd_usb>;
> > +};
> > +
> > +&usbphyc_port1 {
> > + phy-supply = <&vdd_usb>;
> > +};
> > +
> > --
> > 2.26.2
>
> If you correct the minor remarks
>
> Reviewed-by: Patrick Delaunay <patrick.delaunay at st.com>
>
> Thanks
>
> Patrick
>
An other minor remarks: need to update a board MAINTAINERS
or it is in a other serie ...
board/seeed/odyssey-stm32mp157c/MAINTAINERS ?
regards
Patrick
More information about the U-Boot
mailing list