[PATCH v2 2/6] dt-bindings: usb: mtu3: add bindings for MediaTek USB3 DRD

[Chunfeng Yun]

Add dt-binding for MediaTek USB3 DRD Driver

Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
---
v2: no changes
---
 doc/device-tree-bindings/usb/mediatek,mtu3.txt | 74 ++++++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 doc/device-tree-bindings/usb/mediatek,mtu3.txt

diff --git a/doc/device-tree-bindings/usb/mediatek,mtu3.txt b/doc/device-tree-bindings/usb/mediatek,mtu3.txt
new file mode 100644
index 0000000..75a6785
--- /dev/null
+++ b/doc/device-tree-bindings/usb/mediatek,mtu3.txt
@@ -0,0 +1,74 @@
+The device node for Mediatek USB3.0 DRD controller
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3",
+	soc-model is the name of SoC, such as mt8512 etc,
+	when using "mediatek,mtu3" compatible string, you need SoC specific
+	ones in addition, one of:
+	- "mediatek,mt8512-mtu3"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be
+ 	- "mac" : device IP,
+	- "ippc" : IP port control
+ - interrupts : interrupt used by the device IP
+ - power-domains : a phandle to USB power domain node to control USB's MTCMOS
+ - vusb33-supply : regulator of USB AVDD3.3v
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+	entry in clock-names
+ - clock-names : must contain "sys_ck" for clock of controller,
+	the following clocks are optional:
+	"ref_ck", "mcu_ck" and "dma_ck";
+ - phys : list of all the USB PHYs on this HCD
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+	see : usb/generic.txt
+
+Optional properties:
+ - #address-cells, #size-cells : should be '2' if the device has sub-nodes
+	with 'reg' property
+ - ranges : allows valid 1:1 translation between child's address space and
+	parent's address space
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+	dual-role mode.
+ - pinctrl-names : a pinctrl state named "default" is optional
+ - pinctrl-0 : pin control group
+	See: pinctrl/pinctrl-bindings.txt
+
+ - maximum-speed : valid arguments are "full-speed", "high-speed",
+	"super-speed" and "super-speed-plus",
+	see: usb/generic.txt.
+
+Sub-nodes:
+The xhci should be added as subnode to mtu3 as shown in the following example
+if host mode is enabled. The DT binding details of xhci can be found in:
+	- usb/mediatek,mtk-xhci.txt
+
+Example:
+ssusb: usb at 11271000 {
+	compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3";
+	reg = <0 0x11271000 0 0x3000>,
+	      <0 0x11280700 0 0x0100>;
+	reg-names = "mac", "ippc";
+	interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
+	phys = <&phy_port0 PHY_TYPE_USB3>,
+	       <&phy_port1 PHY_TYPE_USB2>;
+	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+	clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+	clock-names = "sys_ck", "ref_ck";
+	vusb33-supply = <&mt6397_vusb_reg>;
+	vbus-supply = <&usb_p0_vbus>;
+	dr_mode = "otg";
+	#address-cells = <2>;
+	#size-cells = <2>;
+	ranges;
+
+	usb_host: xhci at 11270000 {
+		compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci";
+		reg = <0 0x11270000 0 0x1000>;
+		reg-names = "mac";
+		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+		clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>;
+		clock-names = "sys_ck", "ref_ck";
+		vusb33-supply = <&mt6397_vusb_reg>;
+	};
+};
-- 
1.9.1