test/py GPIO failure in u-boot/master

[Tom Rini]

On Wed, Jul 08, 2020 at 09:50:06AM -0600, Stephen Warren wrote:
> Latest u-boot/master is failing a couple test/py test_ut tests for GPIO:
> 
> > => ut dm gpio
> > Test: dm_test_gpio: gpio.c
> > extra-gpios: get_value: error: gpio b5 not reserved
> > /var/lib/jenkins/workspace/u-boot-denx_uboot-master-build/src/u-boot/test/dm/gpio.c:137, dm_test_gpio (): 0 == gpio_lookup_name ("hog_input_active_low", & dev, & offset, & gpio): Expected 0x0 (0), got 0xffffffea (-22)
> > Test: dm_test_gpio: gpio.c (flat tree)
> > extra-gpios: get_value: error: gpio b5 not reserved
> > /var/lib/jenkins/workspace/u-boot-denx_uboot-master-build/src/u-boot/test/dm/gpio.c:137, dm_test_gpio (): 0 == gpio_lookup_name ("hog_input_active_low", & dev, & offset, & gpio): Expected 0x0 (0), got 0xffffffea (-22)
> > Failures: 2
> 
> 
> > => ut dm gpio_leak
> > Test: dm_test_gpio_leak: gpio.c
> > extra-gpios: get_value: error: gpio b5 not reserved
> > /var/lib/jenkins/workspace/u-boot-denx_uboot-master-build/src/u-boot/test/dm/gpio.c:137, dm_test_gpio (): 0 == gpio_lookup_name ("hog_input_active_low", & dev, & offset, & gpio): Expected 0x0 (0), got 0xffffffea (-22)
> > /var/lib/jenkins/workspace/u-boot-denx_uboot-master-build/src/u-boot/test/dm/gpio.c:302, dm_test_gpio_leak (): 0 == dm_test_gpio (ut): Expected 0x0 ( 0), got 0x1 (1)
> > Test: dm_test_gpio_leak: gpio.c (flat tree)
> > extra-gpios: get_value: error: gpio b5 not reserved
> > /var/lib/jenkins/workspace/u-boot-denx_uboot-master-build/src/u-boot/test/dm/gpio.c:137, dm_test_gpio (): 0 == gpio_lookup_name ("hog_input_active_low", & dev, & offset, & gpio): Expected 0x0 (0), got 0xffffffea (-22)
> > /var/lib/jenkins/workspace/u-boot-denx_uboot-master-build/src/u-boot/test/dm/gpio.c:302, dm_test_gpio_leak (): 0 == dm_test_gpio (ut): Expected 0x0 ( 0), got 0x1 (1)
> > Failures: 4
> 
> This was introduced by one of the following changes; I'd assume due to
> the GPIO patch:
> 
> > cmd: part: Add subcommand to list supported partition tables (detail)
> > cmd: fs: Add command to list supported fs types (detail)
> > cmd: dm: Fixed/Added DM driver listing subcommands (detail)
> > cmd: blkls: Add blkls command (detail)
> > image: Add support for ZSTD decompression (detail)
> > Actions: OWL: Calculate SDRAM size (detail)
> > arm: actions: remove "CONFIG_SYS_SDRAM_SIZE" for Actions Owl Semi SoCs (detail)
> > clk: actions: Add Ethernet clocks (detail)
> > net: phy: realtek: Add support for RTL8201F PHY module. (detail)
> > net: phy: realtek: Introduce PHY_RTL8201F_S700_RMII_TIMINGS to adjust (detail)
> > net: designware: s700: Add glue code for S700 mac (detail)
> > arm: dts: s700: add node for ethernet controller (detail)
> > owl: Kconfig: Enable DM eth for OWL platform (detail)
> > configs: Enable mac and phy configs (detail)
> > gpio: search for gpio label if gpio is not found through bank name (detail)
> > test_sleep.py: make sleep time and margin configurable (detail)
> > fs: fat_write: fix short name creation. (detail)
> > trace: clang compatible handling of gd register (detail)
> > arm: remove outdated comment concerning -ffixed-x18 (detail)
> > arm: use correct argument size of special registers (detail)
> > arm: vexpress64: Fix counter frequency (detail)
> > net: dm: Remove warning about EEPROM provided MAC address (detail)
> > net: smc911x: Properly handle EEPROM MAC address (detail)
> > arm: juno: Enable DM_ETH (detail)
> > sata_sil: Enable DM_PCI operation (detail)
> > arm: juno: Enable PCI (detail)
> > arm: juno: Enable SATA controller (detail)
> 
> I see what was probably an attempt to fix this:
> 
> > commit 7012865e961ca2645d783adf4b75ca4abdbfe5a7 (u-boot/master)
> > Author: Heiko Schocher <hs at denx.de>
> > Date:   Wed Jul 8 10:24:00 2020 +0200
> > 
> >     gpio: fix test.py for gpio label lookup
> 
> ... but the tests are still failing after that. Did that patch edit the
> wrong defconfig, or is there an incremental build issue that prevented
> that patch being effective?

The tests are passing here and in GitLab again, so I'm not sure what's
happening on your end.

-- 
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200708/d28d637c/attachment.sig>