[PATCH 02/10] board_f: m68k: Factor out m68k-specific bdinfo setup

Ovidiu Panait ovidiu.panait at windriver.com
Thu Jul 9 10:04:49 CEST 2020


Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in
arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where
possible.

Signed-off-by: Ovidiu Panait <ovidiu.panait at windriver.com>
---

 arch/m68k/lib/bdinfo.c | 32 ++++++++++++++++++++++++++++++++
 common/board_f.c       | 14 ++++----------
 2 files changed, 36 insertions(+), 10 deletions(-)

diff --git a/arch/m68k/lib/bdinfo.c b/arch/m68k/lib/bdinfo.c
index 971c47c306..83e367b502 100644
--- a/arch/m68k/lib/bdinfo.c
+++ b/arch/m68k/lib/bdinfo.c
@@ -11,6 +11,38 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
+int arch_setup_bdinfo(void)
+{
+	bd_t *bd = gd->bd;
+
+	/*
+	 * Save local variables to board info struct
+	 */
+	bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;	/* start of memory */
+	bd->bi_memsize = gd->ram_size;			/* size in bytes */
+
+#ifdef CONFIG_SYS_SRAM_BASE
+	bd->bi_sramstart = CONFIG_SYS_SRAM_BASE; /* start of SRAM */
+	bd->bi_sramsize = CONFIG_SYS_SRAM_SIZE;  /* size  of SRAM */
+#endif
+
+	bd->bi_mbar_base = CONFIG_SYS_MBAR; /* base of internal registers */
+
+	bd->bi_intfreq = gd->cpu_clk;	/* Internal Freq, in Hz */
+	bd->bi_busfreq = gd->bus_clk;	/* Bus Freq,      in Hz */
+
+	if (IS_ENABLED(CONFIG_PCI))
+		bd->bi_pcifreq = gd->pci_clk;
+
+#if defined(CONFIG_EXTRA_CLOCK)
+	bd->bi_inpfreq = gd->arch.inp_clk;	/* input Freq in Hz */
+	bd->bi_vcofreq = gd->arch.vco_clk;	/* vco Freq in Hz */
+	bd->bi_flbfreq = gd->arch.flb_clk;	/* flexbus Freq in Hz */
+#endif
+
+	return 0;
+}
+
 void arch_print_bdinfo(void)
 {
 	bd_t *bd = gd->bd;
diff --git a/common/board_f.c b/common/board_f.c
index e597749d2f..7d65879b93 100644
--- a/common/board_f.c
+++ b/common/board_f.c
@@ -602,7 +602,7 @@ __weak int arch_setup_bdinfo(void)
 	return 0;
 }
 
-#if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
+#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 static int setup_board_part1(void)
 {
@@ -622,9 +622,6 @@ static int setup_board_part1(void)
 #if defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
 	bd->bi_immr_base = CONFIG_SYS_IMMR;	/* base  of IMMR register     */
 #endif
-#if defined(CONFIG_M68K)
-	bd->bi_mbar_base = CONFIG_SYS_MBAR;	/* base of internal registers */
-#endif
 #if defined(CONFIG_MPC83xx)
 	bd->bi_immrbar = CONFIG_SYS_IMMR;
 #endif
@@ -633,7 +630,7 @@ static int setup_board_part1(void)
 }
 #endif
 
-#if defined(CONFIG_PPC) || defined(CONFIG_M68K)
+#if defined(CONFIG_PPC)
 static int setup_board_part2(void)
 {
 	bd_t *bd = gd->bd;
@@ -646,9 +643,6 @@ static int setup_board_part2(void)
 	bd->bi_sccfreq = gd->arch.scc_clk;
 	bd->bi_vco = gd->arch.vco_out;
 #endif /* CONFIG_CPM2 */
-#if defined(CONFIG_M68K) && defined(CONFIG_PCI)
-	bd->bi_pcifreq = gd->pci_clk;
-#endif
 #if defined(CONFIG_EXTRA_CLOCK)
 	bd->bi_inpfreq = gd->arch.inp_clk;	/* input Freq in Hz */
 	bd->bi_vcofreq = gd->arch.vco_clk;	/* vco Freq in Hz */
@@ -980,11 +974,11 @@ static const init_fnc_t init_sequence_f[] = {
 	dram_init_banksize,
 	show_dram_config,
 	arch_setup_bdinfo,
-#if defined(CONFIG_M68K) || defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
+#if defined(CONFIG_MIPS) || defined(CONFIG_PPC) || \
 	defined(CONFIG_SH)
 	setup_board_part1,
 #endif
-#if defined(CONFIG_PPC) || defined(CONFIG_M68K)
+#if defined(CONFIG_PPC)
 	INIT_FUNC_WATCHDOG_RESET
 	setup_board_part2,
 #endif
-- 
2.17.1



More information about the U-Boot mailing list