[PATCH v2 1/3] lib: fdt: Introduce fdtdec_setup_mem_size_base_lowest()

[Michal Simek]

New function should be called from board dram_init() because it initialized
gd->ram_base/ram_size. It finds the lowest available memory.

On systems with multiple memory nodes finding out the first memory node by
fdtdec_setup_mem_size_base() is not enough because this memory can be above
actual U-Boot VA mapping. Currently only mapping till 39bit is supported
(Full 44bit mapping was removed by commit 7985cdf74b28 ("arm64: Remove
non-full-va map code")).
If DT starts with the first memory node above 39bit address then system can
be unpredictable.

The function is available only when multiple memory bank support is
enabled.

Calling fdtdec_setup_memory_banksize() from dram_init() is not possible
because fdtdec_setup_memory_banksize() is saving dram information to bd
structure which is placed on stack but not initialized at this time. Also
stack is placed at location setup in dram_init().

Signed-off-by: Michal Simek <michal.simek at xilinx.com>
---

Changes in v2:
- Separate Xilinx change from generic patch

 include/fdtdec.h | 17 +++++++++++++++++
 lib/fdtdec.c     | 45 +++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 62 insertions(+)

diff --git a/include/fdtdec.h b/include/fdtdec.h
index 760b392bdfbc..bc79389260ab 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -926,6 +926,23 @@ int fdtdec_decode_display_timing(const void *blob, int node, int index,
  */
 int fdtdec_setup_mem_size_base(void);
 
+/**
+ * fdtdec_setup_mem_size_base_lowest() - decode and setup gd->ram_size and
+ * gd->ram_start by lowest available memory base
+ *
+ * Decode the /memory 'reg' property to determine the lowest start of the memory
+ * bank bank and populate the global data with it.
+ *
+ * This function should be called from a boards dram_init(). This helper
+ * function allows for boards to query the device tree for DRAM size and start
+ * address instead of hard coding the value in the case where the memory size
+ * and start address cannot be detected automatically.
+ *
+ * @return 0 if OK, -EINVAL if the /memory node or reg property is missing or
+ * invalid
+ */
+int fdtdec_setup_mem_size_base_lowest(void);
+
 /**
  * fdtdec_setup_memory_banksize() - decode and populate gd->bd->bi_dram
  *
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index fa523ce2e908..a10120baa895 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -1106,6 +1106,51 @@ int fdtdec_setup_memory_banksize(void)
 
 	return 0;
 }
+
+int fdtdec_setup_mem_size_base_lowest(void)
+{
+	int bank, ret, mem, reg = 0;
+	struct fdt_resource res;
+	unsigned long base;
+	phys_size_t size;
+	const void *blob = gd->fdt_blob;
+
+	gd->ram_base = (unsigned long)~0;
+
+	mem = get_next_memory_node(blob, -1);
+	if (mem < 0) {
+		debug("%s: Missing /memory node\n", __func__);
+		return -EINVAL;
+	}
+
+	for (bank = 0; bank < CONFIG_NR_DRAM_BANKS; bank++) {
+		ret = fdt_get_resource(blob, mem, "reg", reg++, &res);
+		if (ret == -FDT_ERR_NOTFOUND) {
+			reg = 0;
+			mem = get_next_memory_node(blob, mem);
+			if (mem == -FDT_ERR_NOTFOUND)
+				break;
+
+			ret = fdt_get_resource(blob, mem, "reg", reg++, &res);
+			if (ret == -FDT_ERR_NOTFOUND)
+				break;
+		}
+		if (ret != 0)
+			return -EINVAL;
+
+		base = (unsigned long)res.start;
+		size = (phys_size_t)(res.end - res.start + 1);
+
+		if (gd->ram_base > base && size) {
+			gd->ram_base = base;
+			gd->ram_size = size;
+			debug("%s: Initial DRAM base %lx size %lx\n",
+			      __func__, base, (unsigned long)size);
+		}
+	}
+
+	return 0;
+}
 #endif
 
 #if CONFIG_IS_ENABLED(MULTI_DTB_FIT)
-- 
2.27.0