[PATCH v2 5/6] arm64: dts: meson: import libretech-pc from linux v5.6-rc2
Neil Armstrong
narmstrong at baylibre.com
Mon Mar 2 10:34:09 CET 2020
On 27/02/2020 12:27, Jerome Brunet wrote:
> Sync the libretech-pc device tree from Linux v5.6-rc2
> 11a48a5a18c6 ("Linux 5.6-rc2")
>
> Signed-off-by: Jerome Brunet <jbrunet at baylibre.com>
> ---
> arch/arm/dts/meson-gx-libretech-pc.dtsi | 375 ++++++++++++++++++
> arch/arm/dts/meson-gxl-s905d-libretech-pc.dts | 16 +
> arch/arm/dts/meson-gxl-s905d.dtsi | 12 +
> arch/arm/dts/meson-gxm-s912-libretech-pc.dts | 62 +++
> 4 files changed, 465 insertions(+)
> create mode 100644 arch/arm/dts/meson-gx-libretech-pc.dtsi
> create mode 100644 arch/arm/dts/meson-gxl-s905d-libretech-pc.dts
> create mode 100644 arch/arm/dts/meson-gxl-s905d.dtsi
> create mode 100644 arch/arm/dts/meson-gxm-s912-libretech-pc.dts
>
> diff --git a/arch/arm/dts/meson-gx-libretech-pc.dtsi b/arch/arm/dts/meson-gx-libretech-pc.dtsi
> new file mode 100644
> index 000000000000..248b018c83d5
> --- /dev/null
> +++ b/arch/arm/dts/meson-gx-libretech-pc.dtsi
> @@ -0,0 +1,375 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 BayLibre SAS.
> + * Author: Jerome Brunet <jbrunet at baylibre.com>
> + */
> +
> +/* Libretech Amlogic GX PC form factor - AKA: Tartiflette */
> +
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + adc-keys {
> + compatible = "adc-keys";
> + io-channels = <&saradc 0>;
> + io-channel-names = "buttons";
> + keyup-threshold-microvolt = <1800000>;
> +
> + update-button {
> + label = "update";
> + linux,code = <KEY_VENDOR>;
> + press-threshold-microvolt = <1300000>;
> + };
> + };
> +
> + aliases {
> + serial0 = &uart_AO;
> + ethernet0 = ðmac;
> + spi0 = &spifc;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + cvbs-connector {
> + compatible = "composite-video-connector";
> + status = "disabled";
> +
> + port {
> + cvbs_connector_in: endpoint {
> + remote-endpoint = <&cvbs_vdac_out>;
> + };
> + };
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> + };
> +
> + hdmi-connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&hdmi_tx_tmds_out>;
> + };
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + poll-interval = <100>;
> +
> + power-button {
> + label = "power";
> + linux,code = <KEY_POWER>;
> + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + memory at 0 {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + ao_5v: regulator-ao_5v {
> + compatible = "regulator-fixed";
> + regulator-name = "AO_5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&dc_in>;
> + regulator-always-on;
> + };
> +
> + dc_in: regulator-dc_in {
> + compatible = "regulator-fixed";
> + regulator-name = "DC_IN";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + green {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_DISK_ACTIVITY;
> + gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "disk-activity";
> + };
> +
> + blue {
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + panic-indicator;
> + };
> + };
> +
> + vcc_card: regulator-vcc_card {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC_CARD";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&vddio_ao3v3>;
> +
> + gpio = <&gpio GPIODV_4 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + vcc5v: regulator-vcc5v {
> + compatible = "regulator-fixed";
> + regulator-name = "VCC5V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&ao_5v>;
> +
> + gpio = <&gpio GPIOH_3 GPIO_OPEN_DRAIN>;
> + };
> +
> + vddio_ao18: regulator-vddio_ao18 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&ao_5v>;
> + regulator-always-on;
> + };
> +
> + vddio_ao3v3: regulator-vddio_ao3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_AO3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ao_5v>;
> + regulator-always-on;
> + };
> +
> + vddio_boot: regulator-vddio_boot {
> + compatible = "regulator-fixed";
> + regulator-name = "VDDIO_BOOT";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vddio_ao3v3>;
> + regulator-always-on;
> + };
> +
> + vddio_card: regulator-vddio-card {
> + compatible = "regulator-gpio";
> + regulator-name = "VDDIO_CARD";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&gpio GPIODV_5 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> +
> + states = <3300000 0>,
> + <1800000 1>;
> +
> + regulator-settling-time-up-us = <200>;
> + regulator-settling-time-down-us = <50000>;
> + };
> +};
> +
> +&cec_AO {
> + pinctrl-0 = <&ao_cec_pins>;
> + pinctrl-names = "default";
> + hdmi-phandle = <&hdmi_tx>;
> + status = "okay";
> +};
> +
> +&cvbs_vdac_port {
> + cvbs_vdac_out: endpoint {
> + remote-endpoint = <&cvbs_connector_in>;
> + };
> +};
> +
> +ðmac {
> + pinctrl-0 = <ð_pins>, <ð_phy_irq_pins>;
> + pinctrl-names = "default";
> + phy-handle = <&external_phy>;
> + amlogic,tx-delay-ns = <2>;
> + phy-mode = "rgmii";
> + status = "okay";
> +};
> +
> +&external_mdio {
> + external_phy: ethernet-phy at 0 {
> + reg = <0>;
> + max-speed = <1000>;
> + reset-assert-us = <10000>;
> + reset-deassert-us = <30000>;
> + reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
> + interrupt-parent = <&gpio_intc>;
> + interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
> + };
> +};
> +
> +&pinctrl_periphs {
> + /*
> + * Make sure the reset pin of the usb HUB is driven high to take
> + * it out of reset.
> + */
> + usb1_rst_pins: usb1_rst_irq {
> + mux {
> + groups = "GPIODV_3";
> + function = "gpio_periphs";
> + bias-disable;
> + output-high;
> + };
> + };
> +
> + /* Make sure the phy irq pin is properly configured as input */
> + eth_phy_irq_pins: eth_phy_irq {
> + mux {
> + groups = "GPIOZ_15";
> + function = "gpio_periphs";
> + bias-disable;
> + output-disable;
> + };
> + };
> +};
> +
> +&hdmi_tx {
> + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> + pinctrl-names = "default";
> + hdmi-supply = <&vcc5v>;
> + status = "okay";
> +};
> +
> +&hdmi_tx_tmds_port {
> + hdmi_tx_tmds_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> +};
> +
> +&ir {
> + pinctrl-0 = <&remote_input_ao_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&i2c_C {
> + pinctrl-0 = <&i2c_c_dv18_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + rtc: rtc at 51 {
> + reg = <0x51>;
> + compatible = "nxp,pcf8563";
> + #clock-cells = <0>;
> + clock-output-names = "rtc_clkout";
> + };
> +};
> +
> +&pwm_AO_ab {
> + pinctrl-0 = <&pwm_ao_a_3_pins>;
> + pinctrl-names = "default";
> + clocks = <&clkc CLKID_FCLK_DIV4>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
> +&pwm_ab {
> + pinctrl-0 = <&pwm_b_pins>;
> + pinctrl-names = "default";
> + clocks = <&clkc CLKID_FCLK_DIV4>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
> +&pwm_ef {
> + pinctrl-0 = <&pwm_e_pins>, <&pwm_f_clk_pins>;
> + pinctrl-names = "default";
> + clocks = <&clkc CLKID_FCLK_DIV4>;
> + clock-names = "clkin0";
> + status = "okay";
> +};
> +
> +&saradc {
> + vref-supply = <&vddio_ao18>;
> + status = "okay";
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> + pinctrl-0 = <&sdcard_pins>;
> + pinctrl-1 = <&sdcard_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-ddr50;
> + max-frequency = <200000000>;
> + disable-wp;
> +
> + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
> +
> + vmmc-supply = <&vcc_card>;
> + vqmmc-supply = <&vddio_card>;
> +
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> + pinctrl-0 = <&emmc_pins>;
> + pinctrl-1 = <&emmc_clk_gate_pins>;
> + pinctrl-names = "default", "clk-gate";
> +
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + mmc-ddr-1_8v;
> + mmc-hs200-1_8v;
> + max-frequency = <200000000>;
> + disable-wp;
> +
> + mmc-pwrseq = <&emmc_pwrseq>;
> + vmmc-supply = <&vddio_ao3v3>;
> + vqmmc-supply = <&vddio_boot>;
> +
> + status = "okay";
> +};
> +
> +&spifc {
> + pinctrl-0 = <&nor_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + gd25lq128: spi-flash at 0 {
> + compatible = "jedec,spi-nor";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + reg = <0>;
> + spi-max-frequency = <12000000>;
> + };
> +};
> +
> +&uart_AO {
> + pinctrl-0 = <&uart_ao_a_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&usb2_phy0 {
> + pinctrl-0 = <&usb1_rst_pins>;
> + pinctrl-names = "default";
> + phy-supply = <&vcc5v>;
> +};
> +
> +&usb2_phy1 {
> + phy-supply = <&vcc5v>;
> +};
> diff --git a/arch/arm/dts/meson-gxl-s905d-libretech-pc.dts b/arch/arm/dts/meson-gxl-s905d-libretech-pc.dts
> new file mode 100644
> index 000000000000..100a1cfeea15
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxl-s905d-libretech-pc.dts
> @@ -0,0 +1,16 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 BayLibre SAS. All rights reserved.
> + * Author: Jerome Brunet <jbrunet at baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-gxl-s905d.dtsi"
> +#include "meson-gx-libretech-pc.dtsi"
> +
> +/ {
> + compatible = "libretech,aml-s905d-pc", "amlogic,s905d",
> + "amlogic,meson-gxl";
> + model = "Libre Computer AML-S905D-PC";
> +};
> diff --git a/arch/arm/dts/meson-gxl-s905d.dtsi b/arch/arm/dts/meson-gxl-s905d.dtsi
> new file mode 100644
> index 000000000000..43321919547a
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxl-s905d.dtsi
> @@ -0,0 +1,12 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2016 Endless Computers, Inc.
> + * Author: Carlo Caione <carlo at endlessm.com>
> + */
> +
> +#include "meson-gxl.dtsi"
> +#include "meson-gxl-mali.dtsi"
> +
> +/ {
> + compatible = "amlogic,s905d", "amlogic,meson-gxl";
> +};
> diff --git a/arch/arm/dts/meson-gxm-s912-libretech-pc.dts b/arch/arm/dts/meson-gxm-s912-libretech-pc.dts
> new file mode 100644
> index 000000000000..444c249863cb
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxm-s912-libretech-pc.dts
> @@ -0,0 +1,62 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019 BayLibre SAS. All rights reserved.
> + * Author: Jerome Brunet <jbrunet at baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-gxm.dtsi"
> +#include "meson-gx-libretech-pc.dtsi"
> +
> +/ {
> + compatible = "libretech,aml-s912-pc", "amlogic,s912",
> + "amlogic,meson-gxm";
> + model = "Libre Computer AML-S912-PC";
> +
> + typec2_vbus: regulator-typec2_vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "TYPEC2_VBUS";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&vcc5v>;
> +
> + gpio = <&gpio GPIODV_1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +};
> +
> +&pinctrl_periphs {
> + /*
> + * Make sure the irq pin of the TYPE C controller is not driven
> + * by the SoC.
> + */
> + fusb302_irq_pins: fusb302_irq {
> + mux {
> + groups = "GPIODV_0";
> + function = "gpio_periphs";
> + bias-pull-up;
> + output-disable;
> + };
> + };
> +};
> +
> +&i2c_C {
> + fusb302 at 22 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;
> +
> + pinctrl-0 = <&fusb302_irq_pins>;
> + pinctrl-names = "default";
> + interrupt-parent = <&gpio_intc>;
> + interrupts = <59 IRQ_TYPE_LEVEL_LOW>;
> +
> + vbus-supply = <&typec2_vbus>;
> +
> + status = "okay";
> + };
> +};
> +
> +&usb2_phy2 {
> + phy-supply = <&typec2_vbus>;
> +};
>
Acked-by: Neil Armstrong <narmstrong at baylibre.com>
More information about the U-Boot
mailing list