[PATCH v5 33/33] riscv: Add Sipeed Maix support
Rick Chen
rickchen36 at gmail.com
Wed Mar 4 08:47:09 CET 2020
Hi Sean
This patch series become larger and larger from v1 with 11 patches to
v5 with 33 patches.
You shall just fix the suggestions from the previous version in the
next version.
Additional extra features and subsystem drivers that you want to
support, you shall send them individually instead of mixing them
together.
If you can separate them into different series(spi, gpio,led ,
pinctrl, watchdog, those drivers were not present in v1) and they will
not block the reviewing schedule each other.
Narrow down the dependency, it can help to speed up the patch work.
And I am happy to help pulling the RISC-V relative patchs via riscv
tree ASAP.
Thanks,
Rick
>
> > The Sipeed Maix series is a collection of boards built around the RISC-V
> > Kendryte K210 processor. This processor contains several peripherals to
> > accelerate neural network processing and other "ai" tasks. This includes a
> > "KPU" neural network processor, an audio processor supporting beamforming
> > reception, and a digital video port supporting capture and output at VGA
> > resolution. Other peripherals include 8M of sram (accessible with and
> > without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
> > accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
> > peripherals vary, but include spi flash; on-board usb-serial bridges; ports
> > for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
> > Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
> > similar.
> >
> > Documentation for Maix boards is located at
> > <http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
> > located at <https://kendryte.com/downloads/>. However, hardware details are
> > rather lacking, so most technical reference has been taken from the
> > standalone sdk located at
> > <https://github.com/kendryte/kendryte-standalone-sdk>.
> >
> > Signed-off-by: Sean Anderson <seanga2 at gmail.com>
> > ---
>
> Please check patch, it can not apply
>
>
> Applying: riscv: Add Sipeed Maix support
> .git/rebase-apply/patch:344: trailing whitespace.
>
> .git/rebase-apply/patch:346: trailing whitespace.
>
> .git/rebase-apply/patch:368: trailing whitespace.
>
> .git/rebase-apply/patch:370: trailing whitespace.
>
> .git/rebase-apply/patch:377: trailing whitespace.
> Bytes Sent:2478208 BPS:72937
> error: patch failed: doc/board/index.rst:16
> error: doc/board/index.rst: patch does not apply
> Patch failed at 0001 riscv: Add Sipeed Maix support
>
> Thanks,
> Rick
>
> >
> > Changes in v5:
> > - Configure relocation location with CONFIG_SYS_SDRAM_*
> > - Enable ram clocks
> > - Add pinmux/gpio/led support
> > - Remove (broken) MMC support
> > - Store the environment in flash
> > - Add partitions
> > - Add bootcmd
> > - Add docs for pinctrl and booting
> >
> > Changes in v4:
> > - Rework documentation to be organized by board mfg not cpu mfg
> > - Update docs to reflect working SPI support
> > - Add proper spi support
> > - Don't define unneecessary macros in config.h
> > - Lower the default stack so it isn't clobbered on relocation
> > - Update MAINTAINERS
> > - Update copyright
> >
> > Changes in v3:
> > - Reorder to be last in the patch series
> > - Add documentation for the board
> > - Generate defconfig with "make savedefconfig"
> > - Update Kconfig to imply most features we need
> > - Update MAINTAINERS
> >
> > Changes in v2:
> > - Select CONFIG_SYS_RISCV_NOCOUNTER
> > - Imply CONFIG_CLK_K210
> > - Remove spurious references to CONFIG_ARCH_K210
> > - Remove many configs from defconfig where the defaults were fine
> > - Add a few "not set" lines to suppress unneeded defaults
> > - Reduce pre-reloc malloc space, now that clocks initialization happens
> > later
> >
> > arch/riscv/Kconfig | 4 +
> > board/sipeed/maix/Kconfig | 72 ++++++++++
> > board/sipeed/maix/MAINTAINERS | 11 ++
> > board/sipeed/maix/Makefile | 5 +
> > board/sipeed/maix/maix.c | 54 +++++++
> > configs/sipeed_maix_bitm_defconfig | 16 +++
> > doc/board/index.rst | 1 +
> > doc/board/sipeed/index.rst | 9 ++
> > doc/board/sipeed/maix.rst | 223 +++++++++++++++++++++++++++++
> > include/configs/sipeed-maix.h | 24 ++++
> > 10 files changed, 419 insertions(+)
> > create mode 100644 board/sipeed/maix/Kconfig
> > create mode 100644 board/sipeed/maix/MAINTAINERS
> > create mode 100644 board/sipeed/maix/Makefile
> > create mode 100644 board/sipeed/maix/maix.c
> > create mode 100644 configs/sipeed_maix_bitm_defconfig
> > create mode 100644 doc/board/sipeed/index.rst
> > create mode 100644 doc/board/sipeed/maix.rst
> > create mode 100644 include/configs/sipeed-maix.h
> >
> > diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> > index b7a5757584..d016dd75d7 100644
> > --- a/arch/riscv/Kconfig
> > +++ b/arch/riscv/Kconfig
> > @@ -20,6 +20,9 @@ config TARGET_QEMU_VIRT
> > config TARGET_SIFIVE_FU540
> > bool "Support SiFive FU540 Board"
> >
> > +config TARGET_SIPEED_MAIX
> > + bool "Support Sipeed Maix Board"
> > +
> > endchoice
> >
> > config SYS_ICACHE_OFF
> > @@ -53,6 +56,7 @@ source "board/AndesTech/ax25-ae350/Kconfig"
> > source "board/emulation/qemu-riscv/Kconfig"
> > source "board/microchip/mpfs_icicle/Kconfig"
> > source "board/sifive/fu540/Kconfig"
> > +source "board/sipeed/maix/Kconfig"
> >
> > # platform-specific options below
> > source "arch/riscv/cpu/ax25/Kconfig"
> > diff --git a/board/sipeed/maix/Kconfig b/board/sipeed/maix/Kconfig
> > new file mode 100644
> > index 0000000000..939eb4829a
> > --- /dev/null
> > +++ b/board/sipeed/maix/Kconfig
> > @@ -0,0 +1,72 @@
> > +# SPDX-License-Identifier: GPL-2.0+
> > +# Copyright (C) 2019-20 Sean Anderson <seanga2 at gmail.com>
> > +
> > +if TARGET_SIPEED_MAIX
> > +
> > +config SYS_BOARD
> > + default "maix"
> > +
> > +config SYS_VENDOR
> > + default "sipeed"
> > +
> > +config SYS_CPU
> > + default "generic"
> > +
> > +config SYS_CONFIG_NAME
> > + default "sipeed-maix"
> > +
> > +config SYS_TEXT_BASE
> > + default 0x80000000
> > +
> > +config DEFAULT_DEVICE_TREE
> > + default "k210-maix-bit"
> > +
> > +config NR_CPUS
> > + default 2
> > +
> > +config NR_DRAM_BANKS
> > + default 3
> > +
> > +config SF_DEFAULT_BUS
> > + default 3
> > +
> > +config BOARD_SPECIFIC_OPTIONS
> > + def_bool y
> > + select GENERIC_RISCV
> > + select RISCV_PRIV_1_9
> > + imply SMP
> > + imply OF_BOARD_SETUP
> > + imply DM_SERIAL
> > + imply SIFIVE_SERIAL
> > + imply SIFIVE_CLINT
> > + imply POWER_DOMAIN
> > + imply SIMPLE_PM_BUS
> > + imply CLK_CCF
> > + imply CLK_COMPOSITE_CCF
> > + imply CLK_K210
> > + imply DM_RESET
> > + imply RESET_SYSCON
> > + imply SYSRESET
> > + imply SYSRESET_SYSCON
> > + imply PINCTRL
> > + imply PINCONF
> > + imply PINCTRL_K210
> > + imply DM_GPIO
> > + imply DWAPB_GPIO
> > + imply SIFIVE_GPIO
> > + imply CMD_GPIO
> > + imply LED
> > + imply LED_GPIO
> > + imply SPI
> > + imply DESIGNWARE_SPI
> > + imply SPI_FLASH_WINBOND
> > + imply DM_MTD
> > + imply SPI_FLASH_MTD
> > + imply CMD_MTD
> > + imply ENV_IS_IN_SPI_FLASH
> > + imply MMC
> > + imply MMC_BROKEN_CD
> > + imply MMC_SPI
> > + imply WDT
> > + imply DESIGNWARE_WATCHDOG
> > +endif
> > diff --git a/board/sipeed/maix/MAINTAINERS b/board/sipeed/maix/MAINTAINERS
> > new file mode 100644
> > index 0000000000..1f33882e1e
> > --- /dev/null
> > +++ b/board/sipeed/maix/MAINTAINERS
> > @@ -0,0 +1,11 @@
> > +Sipeed Maix BOARD
> > +M: Sean Anderson <seanga2 at gmail.com>
> > +S: Maintained
> > +F: arch/riscv/dts/k210.dtsi
> > +F: arch/riscv/dts/k210-maix-bit.dts
> > +F: board/sipeed/maix/
> > +F: configs/sipeed_maix_defconfig
> > +F: doc/board/sipeed/
> > +F: include/configs/sipeed-maix.h
> > +F: include/dt-bindings/*/k210-sysctl.h
> > +F: test/dm/k210_pll.c
> > diff --git a/board/sipeed/maix/Makefile b/board/sipeed/maix/Makefile
> > new file mode 100644
> > index 0000000000..4acff5b31e
> > --- /dev/null
> > +++ b/board/sipeed/maix/Makefile
> > @@ -0,0 +1,5 @@
> > +# SPDX-License-Identifier: GPL-2.0+
> > +#
> > +# Copyright (c) 2019 Western Digital Corporation or its affiliates.
> > +
> > +obj-y += maix.o
> > diff --git a/board/sipeed/maix/maix.c b/board/sipeed/maix/maix.c
> > new file mode 100644
> > index 0000000000..c126cb5d67
> > --- /dev/null
> > +++ b/board/sipeed/maix/maix.c
> > @@ -0,0 +1,54 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright (C) 2019 Sean Anderson <seanga2 at gmail.com>
> > + */
> > +
> > +#include <common.h>
> > +#include <clk.h>
> > +#include <dm.h>
> > +#include <fdt_support.h>
> > +
> > +phys_size_t get_effective_memsize(void)
> > +{
> > + return CONFIG_SYS_SDRAM_SIZE;
> > +}
> > +
> > +int board_init(void)
> > +{
> > + int ret;
> > + ofnode bank = ofnode_null();
> > +
> > + /* Enable RAM clocks */
> > + while (true) {
> > + struct clk clk;
> > +
> > + bank = ofnode_by_prop_value(bank, "device_type", "memory",
> > + sizeof("memory"));
> > + if (ofnode_equal(bank, ofnode_null()))
> > + break;
> > +
> > + ret = clk_get_by_index_nodev(bank, 0, &clk);
> > + if (ret)
> > + continue;
> > +
> > + ret = clk_enable(&clk);
> > + clk_free(&clk);
> > + if (ret)
> > + return ret;
> > + }
> > + return 0;
> > +}
> > +
> > +int ft_board_setup(void *blob, bd_t *bd)
> > +{
> > + int i;
> > + u64 base[CONFIG_NR_DRAM_BANKS];
> > + u64 size[CONFIG_NR_DRAM_BANKS];
> > +
> > + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
> > + base[i] = bd->bi_dram[i].start;
> > + size[i] = bd->bi_dram[i].size;
> > + }
> > +
> > + return fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
> > +}
> > diff --git a/configs/sipeed_maix_bitm_defconfig b/configs/sipeed_maix_bitm_defconfig
> > new file mode 100644
> > index 0000000000..7f644e7a37
> > --- /dev/null
> > +++ b/configs/sipeed_maix_bitm_defconfig
> > @@ -0,0 +1,16 @@
> > +CONFIG_RISCV=y
> > +CONFIG_ENV_SIZE=0x2000
> > +CONFIG_ENV_SECT_SIZE=0x1000
> > +CONFIG_ENV_OFFSET=0x7C000
> > +CONFIG_ENV_OFFSET_REDUND=0x7E000
> > +CONFIG_TARGET_SIPEED_MAIX=y
> > +CONFIG_ARCH_RV64I=y
> > +CONFIG_USE_BOOTCOMMAND=y
> > +CONFIG_BOOTCOMMAND="sf probe;mtd read kernel 80000000;go 80000000"
> > +CONFIG_MTDIDS_DEFAULT="nor0=spi3.0"
> > +CONFIG_MTDPARTS_DEFAULT="spi3.0:496k(u-boot),16k(env),5632k(kernel),10240k(data)"
> > +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> > +# CONFIG_NET is not set
> > +# CONFIG_INPUT is not set
> > +# CONFIG_DM_ETH is not set
> > +# CONFIG_EFI_LOADER is not set
> > diff --git a/doc/board/index.rst b/doc/board/index.rst
> > index b8b956d730..54cbc5c874 100644
> > --- a/doc/board/index.rst
> > +++ b/doc/board/index.rst
> > @@ -16,4 +16,5 @@ Board-specific doc
> > renesas/index
> > rockchip/index
> > sifive/index
> > + sipeed/index
> > xilinx/index
> > diff --git a/doc/board/sipeed/index.rst b/doc/board/sipeed/index.rst
> > new file mode 100644
> > index 0000000000..92da47fddd
> > --- /dev/null
> > +++ b/doc/board/sipeed/index.rst
> > @@ -0,0 +1,9 @@
> > +.. SPDX-License-Identifier: GPL-2.0+
> > +
> > +Kendryte
> > +========
> > +
> > +.. toctree::
> > + :maxdepth: 2
> > +
> > + maix
> > diff --git a/doc/board/sipeed/maix.rst b/doc/board/sipeed/maix.rst
> > new file mode 100644
> > index 0000000000..c5c2e24ea5
> > --- /dev/null
> > +++ b/doc/board/sipeed/maix.rst
> > @@ -0,0 +1,223 @@
> > +.. SPDX-License-Identifier: GPL-2.0+
> > +.. Copyright (C) 2020 Sean Anderson <seanga2 at gmail.com>
> > +
> > +Maix Bit
> > +========
> > +
> > +Several of the Sipeed Maix series of boards cotain the Kendryte K210 processor,
> > +a 64-bit RISC-V CPU. This processor contains several peripherals to accelerate
> > +neural network processing and other "ai" tasks. This includes a "KPU" neural
> > +network processor, an audio processor supporting beamforming reception, and a
> > +digital video port supporting capture and output at VGA resolution. Other
> > +peripherals include 8M of SRAM (accessible with and without caching); remappable
> > +pins, including 40 GPIOs; AES, FFT, and SHA256 accelerators; a DMA controller;
> > +and I2C, I2S, and SPI controllers. Maix peripherals vary, but include spi flash;
> > +on-board usb-serial bridges; ports for cameras, displays, and sd cards; and
> > +ESP32 chips. Currently, only the Sipeed Maix Bit V2.0 (bitm) is supported, but
> > +the boards are fairly similar.
> > +
> > +Documentation for Maix boards is available from
> > +`Sipeed's website <http://dl.sipeed.com/MAIX/HDK/>`_.
> > +Documentation for the Kendryte K210 is available from
> > +`Kendryte's website <https://kendryte.com/downloads/>`_. However, hardware
> > +details are rather lacking, so most technical reference has been taken from the
> > +`standalone sdk <https://github.com/kendryte/kendryte-standalone-sdk>`_.
> > +
> > +Build and boot steps
> > +--------------------
> > +
> > +To build u-boot, run
> > +
> > +.. code-block:: none
> > +
> > + make sipeed_maix_bitm_defconfig
> > + make CROSS_COMPILE=<your cross compile prefix>
> > +
> > +To flash u-boot to a maix bit, run
> > +
> > +.. code-block:: none
> > +
> > + kflash -tp /dev/<your tty here> -B bit_mic u-boot-dtb.bin
> > +
> > +Boot output should look like the following:
> > +
> > +.. code-block:: none
> > +
> > +
> > + U-Boot 2020.04-rc2-00087-g2221cc09c1-dirty (Feb 28 2020 - 13:53:09 -0500)
> > +
> > + DRAM: 8 MiB
> > + WDT: Started with servicing (60s timeout)
> > + MMC: spi at 53000000:slot at 0: 0
> > + In: serial at 38000000
> > + Out: serial at 38000000
> > + Err: serial at 38000000
> > + Hit any key to stop autoboot: 0
> > + SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB
> > + Reading 5242880 byte(s) at offset 0x00000000
> > + ## Starting application at 0x80000000 ...
> > +
> > +Flashing Images
> > +---------------
> > +
> > +To flash a kernel, transfer it over serial, then write it to the kernel
> > +partition.
> > +
> > +.. code-block:: none
> > +
> > + => loady 80000000 1500000
> > + ## Switch baudrate to 1500000 bps and press ENTER ...
> > +
> > + *** baud: 1500000
> > +
> > + *** baud: 1500000 ***
> > + ## Ready for binary (ymodem) download to 0x80000000 at 1500000 bps...
> > + C
> > + *** file: loader.bin
> > + $ sz -vv loader.bin
> > + Sending: loader.bin
> > + Bytes Sent:2478208 BPS:72937
> > + Sending:
> > + Ymodem sectors/kbytes sent: 0/ 0k
> > + Transfer complete
> > +
> > + *** exit status: 0 ***
> > + ## Total Size = 0x0025d052 = 2478162 Bytes
> > + ## Switch baudrate to 115200 bps and press ESC ...
> > +
> > + *** baud: 115200
> > +
> > + *** baud: 115200 ***
> > + => sf probe
> > + SF: Detected w25q128fw with page size 256 Bytes, erase size 4 KiB, total 16 MiB
> > + => mtd write kernel 80000000 0 25d052
> > + Writing 2478162 byte(s) at offset 0x00000000
> > +
> > +**NB:** kflash adds a 5-byte header to payloads (and a 32-byte trailer) to all
> > +payloads it flashes. If you use kflash to flash your payload, you will need to
> > +account for this header when specifying what offset in spi flash to load from.
> > +
> > +Partition Scheme
> > +^^^^^^^^^^^^^^^^
> > +
> > +There is no partition scheme specified by the manufacturer. The only requirement
> > +imposed by the firmware is that offset 0 will be loaded and ran. The default
> > +partition scheme is
> > +
> > +========= ======== ======
> > +Partition Offset Size
> > +========= ======== ======
> > +u-boot 0x000000 496k
> > +env 0x07C000 16k
> > +kernel 0x080000 5M
> > +data 0x580000 10.5M
> > +========= ======== ======
> > +
> > +Pin Assignment
> > +--------------
> > +
> > +The K210 contains a Fully Programmable I/O Array (FPIOA), which can remap any of
> > +its 256 input functions to any any of 48 output pins. The following table has
> > +the default pin assignments for the BitM.
> > +
> > +===== ========== =======
> > +Pin Function Comment
> > +===== ========== =======
> > +IO_0 JTAG_TCLK
> > +IO_1 JTAG_TDI
> > +IO_2 JTAG_TMS
> > +IO_3 JTAG_TDO
> > +IO_4 UARTHS_RX
> > +IO_5 UARTHS_TX
> > +IO_6 GPIOHS_1
> > +IO_7 GPIOHS_2
> > +IO_8 GPIO_0
> > +IO_9 GPIO_1
> > +IO_10 GPIO_2
> > +IO_11 GPIO_3
> > +IO_12 GPIO_4 Green LED
> > +IO_13 GPIO_5 Red LED
> > +IO_14 GPIO_6 Blue LED
> > +IO_15 GPIO_7
> > +IO_16 GPIOHS_0 ISP
> > +IO_17 GPIOHS_3
> > +IO_18 I2S0_SCLK MIC CLK
> > +IO_19 I2S0_WS MIC WS
> > +IO_20 I2S0_IN_D0 MIC SD
> > +IO_21 GPIOHS_4
> > +IO_22 GPIOHS_5
> > +IO_23 GPIOHS_6
> > +IO_24 GPIOHS_7
> > +IO_25 GPIOHS_8
> > +IO_26 SPI1_D1 MMC MISO
> > +IO_27 SPI1_SCLK MMC CLK
> > +IO_28 SPI1_D0 MMC MOSI
> > +IO_29 GPIOHS_31 MMC CS
> > +IO_30 GPIOHS_9
> > +IO_31 GPIOHS_10
> > +IO_32 GPIOHS_11
> > +IO_33 GPIOHS_12
> > +IO_34 GPIOHS_13
> > +IO_35 GPIOHS_14
> > +IO_36 GPIOHS_28 Panel CS
> > +IO_37 GPIOHS_29 Panel RST
> > +IO_38 GPIOHS_30 Panel DC
> > +IO_39 SPI0_SCK Panel WR
> > +IO_40 SCCP_SDA
> > +IO_41 SCCP_SCLK
> > +IO_42 DVP_RST
> > +IO_43 DVP_VSYNC
> > +IO_44 DVP_PWDN
> > +IO_45 DVP_HSYNC
> > +IO_46 DVP_XCLK
> > +IO_47 DVP_PCLK
> > +===== ========== =======
> > +
> > +Over- and Under-clocking
> > +------------------------
> > +
> > +To change the clock speed of the K210, you will need to enable
> > +``CONFIG_CLK_K210_SET_RATE`` and edit the board's device tree. To do this, add a
> > +section to ``arch/riscv/arch/riscv/dts/k210-maix-bit.dts`` like the following:
> > +
> > +.. code-block:: dts
> > +
> > + &sysclk {
> > + assigned-clocks = <&sysclk K210_CLK_PLL0>;
> > + assigned-clock-rates = <800000000>;
> > + };
> > +
> > +There are three PLLs on the K210: PLL0 is the parent of most of the components,
> > +including the CPU and RAM. PLL1 is the parent of the neural network coprocessor.
> > +PLL2 is the parent of the sound processing devices. Note that child clocks of
> > +PLL0 and PLL2 run at *half* the speed of the PLLs. For example, if PLL0 is
> > +running at 800 MHz, then the CPU will run at 400 MHz. This is the example given
> > +above. The CPU can be overclocked to around 600 MHz, and underclocked to 26 MHz.
> > +
> > +It is possible to set PLL2's parent to PLL0. The plls are more accurate when
> > +converting between similar frequencies. This makes it easier to get an accurate
> > +frequency for I2S. As an example, consider sampling an I2S device at 44.1 kHz.
> > +On this device, the I2S serial clock runs at 64 times the sample rate.
> > +Therefore, we would like to run PLL2 at an even multiple of 2.8224 MHz. If
> > +PLL2's parent is IN0, we could use a frequency of 390 MHz (the same as the CPU's
> > +default speed). Dividing by 138 yields a serial clock of about 2.8261 MHz. This
> > +results in a sample rate of 44.158 kHz---around 50 Hz or .1% too fast. If,
> > +instead, we set PLL2's parent to PLL1 running at 390 MHz, and request a rate of
> > +2.8224 * 136 = 383.8464 MHz, the achieved rate is 383.90625 MHz. Dividing by 136
> > +yields a serial clock of about 2.8228 MHz. This results in a sample rate of
> > +44.107 kHz---just 7 Hz or .02% too fast. This configuration is shown in the
> > +following example:
> > +
> > +.. code-block:: dts
> > +
> > + &sysclk {
> > + assigned-clocks = <&sysclk K210_CLK_PLL1>, <&sysclk K210_CLK_PLL2>;
> > + assigned-clock-parents = <0>, <&sysclk K210_CLK_PLL1>;
> > + assigned-clock-rates = <390000000>, <383846400>;
> > + };
> > +
> > +There are a couple of quirks to the PLLs. First, there are more frequency ratios
> > +just above and below 1.0, but there is a small gap around 1.0. To be explicit,
> > +if the input frequency is 100 MHz, it would be impossible to have an output of
> > +99 or 101 MHz. In addition, there is a maximum frequency for the internal VCO,
> > +so higher input/output frequencies will be less accurate than lower ones.
> > diff --git a/include/configs/sipeed-maix.h b/include/configs/sipeed-maix.h
> > new file mode 100644
> > index 0000000000..a46473fc78
> > --- /dev/null
> > +++ b/include/configs/sipeed-maix.h
> > @@ -0,0 +1,24 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +/*
> > + * Copyright (C) 2019-20 Sean Anderson <seanga2 at gmail.com>
> > + */
> > +
> > +#ifndef CONFIGS_SIPEED_MAIX_H
> > +#define CONFIGS_SIPEED_MAIX_H
> > +
> > +#include <linux/sizes.h>
> > +
> > +#define CONFIG_SYS_LOAD_ADDR 0x80000000
> > +/* Start just below the second bank so we don't clobber it during reloc */
> > +#define CONFIG_SYS_INIT_SP_ADDR 0x803FFFFF
> > +#define CONFIG_SYS_MALLOC_LEN SZ_128K
> > +#define CONFIG_SYS_CACHELINE_SIZE 64
> > +
> > +#define CONFIG_SYS_SDRAM_BASE 0x80000000
> > +/* Don't relocate into AI ram since it isn't set up yet */
> > +#define CONFIG_SYS_SDRAM_SIZE (SZ_4M + SZ_2M)
> > +
> > +/* For early init */
> > +#define K210_SYSCTL_BASE 0x50440000
> > +
> > +#endif /* CONFIGS_SIPEED_MAIX_H */
> > --
> > 2.25.0
> >
More information about the U-Boot
mailing list