[PATCH v6 19/19] riscv: Add Sipeed Maix support
Rick Chen
rickchen36 at gmail.com
Tue Mar 10 10:04:26 CET 2020
Hi Sean
> The Sipeed Maix series is a collection of boards built around the RISC-V
> Kendryte K210 processor. This processor contains several peripherals to
> accelerate neural network processing and other "ai" tasks. This includes a
> "KPU" neural network processor, an audio processor supporting beamforming
> reception, and a digital video port supporting capture and output at VGA
> resolution. Other peripherals include 8M of sram (accessible with and
> without caching); remappable pins, including 40 GPIOs; AES, FFT, and SHA256
> accelerators; a DMA controller; and I2C, I2S, and SPI controllers. Maix
> peripherals vary, but include spi flash; on-board usb-serial bridges; ports
> for cameras, displays, and sd cards; and ESP32 chips. Currently, only the
> Sipeed Maix Bit V2.0 (bitm) is supported, but the boards are fairly
> similar.
>
> Documentation for Maix boards is located at
> <http://dl.sipeed.com/MAIX/HDK/>. Documentation for the Kendryte K210 is
> located at <https://kendryte.com/downloads/>. However, hardware details are
> rather lacking, so most technical reference has been taken from the
> standalone sdk located at
> <https://github.com/kendryte/kendryte-standalone-sdk>.
>
> Signed-off-by: Sean Anderson <seanga2 at gmail.com>
> ---
This patch applying fail
Applying: riscv: Add Sipeed Maix support
error: patch failed: doc/board/index.rst:16
error: doc/board/index.rst: patch does not apply
Patch failed at 0001 riscv: Add Sipeed Maix support
The copy of the patch that failed is found in: .git/rebase-apply/patch
When you have resolved this problem, run "git am --continue".
If you prefer to skip this patch, run "git am --skip" instead.
To restore the original branch and stop patching, run "git am --abort".
I have replied to you the same result in v5
[v5,33/33] riscv: Add Sipeed Maix support
https://patchwork.ozlabs.org/patch/1246869/#2376311
By the way,
you can not mix them (arch, board, configs, doc)together in a patch.
arch/riscv/Kconfig
board/sipeed/maix/ ...
configs/sipeed_maix_bitm_defconfig
doc/board/index.rst
Thanks,
Rick
>
> Changes in v6:
> - Remove trailing whitespace from documentation
> - Remove configuration for spi/pinmux/gpio features
> - Flesh out documentation some more
>
> Changes in v5:
> - Configure relocation location with CONFIG_SYS_SDRAM_*
> - Enable ram clocks
> - Add pinmux/gpio/led support
> - Remove (broken) MMC support
> - Store the environment in flash
> - Add partitions
> - Add bootcmd
> - Add docs for pinctrl and booting
>
> Changes in v4:
> - Rework documentation to be organized by board mfg not cpu mfg
> - Update docs to reflect working SPI support
> - Add proper spi support
> - Don't define unneecessary macros in config.h
> - Lower the default stack so it isn't clobbered on relocation
> - Update MAINTAINERS
> - Update copyright
>
> Changes in v3:
> - Reorder to be last in the patch series
> - Add documentation for the board
> - Generate defconfig with "make savedefconfig"
> - Update Kconfig to imply most features we need
> - Update MAINTAINERS
>
> Changes in v2:
> - Select CONFIG_SYS_RISCV_NOCOUNTER
> - Imply CONFIG_CLK_K210
> - Remove spurious references to CONFIG_ARCH_K210
> - Remove many configs from defconfig where the defaults were fine
> - Add a few "not set" lines to suppress unneeded defaults
> - Reduce pre-reloc malloc space, now that clocks initialization happens
> later
>
> arch/riscv/Kconfig | 4 +
> board/sipeed/maix/Kconfig | 48 +++++
> board/sipeed/maix/MAINTAINERS | 11 ++
> board/sipeed/maix/Makefile | 5 +
> board/sipeed/maix/maix.c | 54 ++++++
> configs/sipeed_maix_bitm_defconfig | 8 +
> doc/board/index.rst | 1 +
> doc/board/sipeed/index.rst | 9 +
> doc/board/sipeed/maix.rst | 298 +++++++++++++++++++++++++++++
> include/configs/sipeed-maix.h | 24 +++
> 10 files changed, 462 insertions(+)
> create mode 100644 board/sipeed/maix/Kconfig
> create mode 100644 board/sipeed/maix/MAINTAINERS
> create mode 100644 board/sipeed/maix/Makefile
> create mode 100644 board/sipeed/maix/maix.c
> create mode 100644 configs/sipeed_maix_bitm_defconfig
> create mode 100644 doc/board/sipeed/index.rst
> create mode 100644 doc/board/sipeed/maix.rst
> create mode 100644 include/configs/sipeed-maix.h
>
> diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
> index b7a5757584..d016dd75d7 100644
> --- a/arch/riscv/Kconfig
> +++ b/arch/riscv/Kconfig
> @@ -20,6 +20,9 @@ config TARGET_QEMU_VIRT
> config TARGET_SIFIVE_FU540
> bool "Support SiFive FU540 Board"
>
> +config TARGET_SIPEED_MAIX
> + bool "Support Sipeed Maix Board"
> +
> endchoice
>
> config SYS_ICACHE_OFF
> @@ -53,6 +56,7 @@ source "board/AndesTech/ax25-ae350/Kconfig"
> source "board/emulation/qemu-riscv/Kconfig"
> source "board/microchip/mpfs_icicle/Kconfig"
> source "board/sifive/fu540/Kconfig"
> +source "board/sipeed/maix/Kconfig"
>
> # platform-specific options below
> source "arch/riscv/cpu/ax25/Kconfig"
> diff --git a/board/sipeed/maix/Kconfig b/board/sipeed/maix/Kconfig
> new file mode 100644
> index 0000000000..8292089fc9
> --- /dev/null
> +++ b/board/sipeed/maix/Kconfig
> @@ -0,0 +1,48 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +# Copyright (C) 2019-20 Sean Anderson <seanga2 at gmail.com>
> +
> +if TARGET_SIPEED_MAIX
> +
> +config SYS_BOARD
> + default "maix"
> +
> +config SYS_VENDOR
> + default "sipeed"
> +
> +config SYS_CPU
> + default "generic"
> +
> +config SYS_CONFIG_NAME
> + default "sipeed-maix"
> +
> +config SYS_TEXT_BASE
> + default 0x80000000
> +
> +config DEFAULT_DEVICE_TREE
> + default "k210-maix-bit"
> +
> +config NR_CPUS
> + default 2
> +
> +config NR_DRAM_BANKS
> + default 3
> +
> +config BOARD_SPECIFIC_OPTIONS
> + def_bool y
> + select GENERIC_RISCV
> + select RISCV_PRIV_1_9
> + imply SMP
> + imply OF_BOARD_SETUP
> + imply DM_SERIAL
> + imply SIFIVE_SERIAL
> + imply SIFIVE_CLINT
> + imply POWER_DOMAIN
> + imply SIMPLE_PM_BUS
> + imply CLK_CCF
> + imply CLK_COMPOSITE_CCF
> + imply CLK_K210
> + imply DM_RESET
> + imply RESET_SYSCON
> + imply SYSRESET
> + imply SYSRESET_SYSCON
> +endif
> diff --git a/board/sipeed/maix/MAINTAINERS b/board/sipeed/maix/MAINTAINERS
> new file mode 100644
> index 0000000000..1f33882e1e
> --- /dev/null
> +++ b/board/sipeed/maix/MAINTAINERS
> @@ -0,0 +1,11 @@
> +Sipeed Maix BOARD
> +M: Sean Anderson <seanga2 at gmail.com>
> +S: Maintained
> +F: arch/riscv/dts/k210.dtsi
> +F: arch/riscv/dts/k210-maix-bit.dts
> +F: board/sipeed/maix/
> +F: configs/sipeed_maix_defconfig
> +F: doc/board/sipeed/
> +F: include/configs/sipeed-maix.h
> +F: include/dt-bindings/*/k210-sysctl.h
> +F: test/dm/k210_pll.c
> diff --git a/board/sipeed/maix/Makefile b/board/sipeed/maix/Makefile
> new file mode 100644
> index 0000000000..4acff5b31e
> --- /dev/null
> +++ b/board/sipeed/maix/Makefile
> @@ -0,0 +1,5 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +# Copyright (c) 2019 Western Digital Corporation or its affiliates.
> +
> +obj-y += maix.o
> diff --git a/board/sipeed/maix/maix.c b/board/sipeed/maix/maix.c
> new file mode 100644
> index 0000000000..c126cb5d67
> --- /dev/null
> +++ b/board/sipeed/maix/maix.c
> @@ -0,0 +1,54 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2019 Sean Anderson <seanga2 at gmail.com>
> + */
> +
> +#include <common.h>
> +#include <clk.h>
> +#include <dm.h>
> +#include <fdt_support.h>
> +
> +phys_size_t get_effective_memsize(void)
> +{
> + return CONFIG_SYS_SDRAM_SIZE;
> +}
> +
> +int board_init(void)
> +{
> + int ret;
> + ofnode bank = ofnode_null();
> +
> + /* Enable RAM clocks */
> + while (true) {
> + struct clk clk;
> +
> + bank = ofnode_by_prop_value(bank, "device_type", "memory",
> + sizeof("memory"));
> + if (ofnode_equal(bank, ofnode_null()))
> + break;
> +
> + ret = clk_get_by_index_nodev(bank, 0, &clk);
> + if (ret)
> + continue;
> +
> + ret = clk_enable(&clk);
> + clk_free(&clk);
> + if (ret)
> + return ret;
> + }
> + return 0;
> +}
> +
> +int ft_board_setup(void *blob, bd_t *bd)
> +{
> + int i;
> + u64 base[CONFIG_NR_DRAM_BANKS];
> + u64 size[CONFIG_NR_DRAM_BANKS];
> +
> + for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
> + base[i] = bd->bi_dram[i].start;
> + size[i] = bd->bi_dram[i].size;
> + }
> +
> + return fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
> +}
> diff --git a/configs/sipeed_maix_bitm_defconfig b/configs/sipeed_maix_bitm_defconfig
> new file mode 100644
> index 0000000000..f48f7f06e9
> --- /dev/null
> +++ b/configs/sipeed_maix_bitm_defconfig
> @@ -0,0 +1,8 @@
> +CONFIG_RISCV=y
> +CONFIG_TARGET_SIPEED_MAIX=y
> +CONFIG_ARCH_RV64I=y
> +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> +# CONFIG_NET is not set
> +# CONFIG_INPUT is not set
> +# CONFIG_DM_ETH is not set
> +# CONFIG_EFI_LOADER is not set
> diff --git a/doc/board/index.rst b/doc/board/index.rst
> index d43e536ca3..94f01bb098 100644
> --- a/doc/board/index.rst
> +++ b/doc/board/index.rst
> @@ -16,5 +16,6 @@ Board-specific doc
> renesas/index
> rockchip/index
> sifive/index
> + sipeed/index
> st/index
> xilinx/index
> diff --git a/doc/board/sipeed/index.rst b/doc/board/sipeed/index.rst
> new file mode 100644
> index 0000000000..3518e2d8f4
> --- /dev/null
> +++ b/doc/board/sipeed/index.rst
> @@ -0,0 +1,9 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +
> +Sipeed
> +======
> +
> +.. toctree::
> + :maxdepth: 2
> +
> + maix
> diff --git a/doc/board/sipeed/maix.rst b/doc/board/sipeed/maix.rst
> new file mode 100644
> index 0000000000..b11ee0182e
> --- /dev/null
> +++ b/doc/board/sipeed/maix.rst
> @@ -0,0 +1,298 @@
> +.. SPDX-License-Identifier: GPL-2.0+
> +.. Copyright (C) 2020 Sean Anderson <seanga2 at gmail.com>
> +
> +Maix Bit
> +========
> +
> +Several of the Sipeed Maix series of boards cotain the Kendryte K210 processor,
> +a 64-bit RISC-V CPU. This processor contains several peripherals to accelerate
> +neural network processing and other "ai" tasks. This includes a "KPU" neural
> +network processor, an audio processor supporting beamforming reception, and a
> +digital video port supporting capture and output at VGA resolution. Other
> +peripherals include 8M of SRAM (accessible with and without caching); remappable
> +pins, including 40 GPIOs; AES, FFT, and SHA256 accelerators; a DMA controller;
> +and I2C, I2S, and SPI controllers. Maix peripherals vary, but include spi flash;
> +on-board usb-serial bridges; ports for cameras, displays, and sd cards; and
> +ESP32 chips. Currently, only the Sipeed Maix Bit V2.0 (bitm) is supported, but
> +the boards are fairly similar.
> +
> +Documentation for Maix boards is available from
> +`Sipeed's website <http://dl.sipeed.com/MAIX/HDK/>`_.
> +Documentation for the Kendryte K210 is available from
> +`Kendryte's website <https://kendryte.com/downloads/>`_. However, hardware
> +details are rather lacking, so most technical reference has been taken from the
> +`standalone sdk <https://github.com/kendryte/kendryte-standalone-sdk>`_.
> +
> +Build and boot steps
> +--------------------
> +
> +To build u-boot, run
> +
> +.. code-block:: none
> +
> + make sipeed_maix_bitm_defconfig
> + make CROSS_COMPILE=<your cross compile prefix>
> +
> +To flash u-boot to a maix bit, run
> +
> +.. code-block:: none
> +
> + kflash -tp /dev/<your tty here> -B bit_mic u-boot-dtb.bin
> +
> +Boot output should look like the following:
> +
> +.. code-block:: none
> +
> + U-Boot 2020.04-rc2-00087-g2221cc09c1-dirty (Feb 28 2020 - 13:53:09 -0500)
> +
> + DRAM: 8 MiB
> + In: serial at 38000000
> + Out: serial at 38000000
> + Err: serial at 38000000
> + =>
> +
> +Loading Images
> +^^^^^^^^^^^^^^
> +
> +To load a kernel, transfer it over serial.
> +
> +.. code-block:: none
> +
> + => loady 80000000 1500000
> + ## Switch baudrate to 1500000 bps and press ENTER ...
> +
> + *** baud: 1500000
> +
> + *** baud: 1500000 ***
> + ## Ready for binary (ymodem) download to 0x80000000 at 1500000 bps...
> + C
> + *** file: loader.bin
> + $ sz -vv loader.bin
> + Sending: loader.bin
> + Bytes Sent:2478208 BPS:72937
> + Sending:
> + Ymodem sectors/kbytes sent: 0/ 0k
> + Transfer complete
> +
> + *** exit status: 0 ***
> + ## Total Size = 0x0025d052 = 2478162 Bytes
> + ## Switch baudrate to 115200 bps and press ESC ...
> +
> + *** baud: 115200
> +
> + *** baud: 115200 ***
> + =>
> +
> +Running Programs
> +^^^^^^^^^^^^^^^^
> +
> +Binaries
> +""""""""
> +
> +To run a bare binary, use the ``go`` command:
> +
> +.. code-block:: none
> +
> + => loady
> + ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
> + C
> + *** file: ./examples/standalone/hello_world.bin
> + $ sz -vv ./examples/standalone/hello_world.bin
> + Sending: hello_world.bin
> + Bytes Sent: 4864 BPS:649
> + Sending:
> + Ymodem sectors/kbytes sent: 0/ 0k
> + Transfer complete
> +
> + *** exit status: 0 ***
> + (CAN) packets, 5 retries
> + ## Total Size = 0x000012f8 = 4856 Bytes
> + => go 80000000
> + ## Starting application at 0x80000000 ...
> + Example expects ABI version 9
> + Actual U-Boot ABI version 9
> + Hello World
> + argc = 1
> + argv[0] = "80000000"
> + argv[1] = "<NULL>"
> + Hit any key to exit ...
> +
> +Legacy Images
> +"""""""""""""
> +
> +To run legacy images, use the ``bootm`` command:
> +
> +.. code-block:: none
> +
> + $ tools/mkimage -A riscv -O u-boot -T standalone -C none -a 80000000 -e 80000000 -d examples/standalone/hello_world.bin hello_world.img
> + Image Name:
> + Created: Thu Mar 5 12:04:10 2020
> + Image Type: RISC-V U-Boot Standalone Program (uncompressed)
> + Data Size: 4856 Bytes = 4.74 KiB = 0.00 MiB
> + Load Address: 80000000
> + Entry Point: 80000000
> +
> + $ picocom -b 115200 /dev/ttyUSB0i
> + => loady
> + ## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
> + C
> + *** file: hello_world.img
> + $ sz -vv hello_world.img
> + Sending: hello_world.img
> + Bytes Sent: 4992 BPS:665
> + Sending:
> + Ymodem sectors/kbytes sent: 0/ 0k
> + Transfer complete
> +
> + *** exit status: 0 ***
> + CAN) packets, 3 retries
> + ## Total Size = 0x00001338 = 4920 Bytes
> + => bootm
> + ## Booting kernel from Legacy Image at 80000000 ...
> + Image Name:
> + Image Type: RISC-V U-Boot Standalone Program (uncompressed)
> + Data Size: 4856 Bytes = 4.7 KiB
> + Load Address: 80000000
> + Entry Point: 80000000
> + Verifying Checksum ... OK
> + Loading Standalone Program
> + Example expects ABI version 9
> + Actual U-Boot ABI version 9
> + Hello World
> + argc = 0
> + argv[0] = "<NULL>"
> + Hit any key to exit ...
> +
> +Over- and Under-clocking
> +------------------------
> +
> +To change the clock speed of the K210, you will need to enable
> +``CONFIG_CLK_K210_SET_RATE`` and edit the board's device tree. To do this, add a
> +section to ``arch/riscv/arch/riscv/dts/k210-maix-bit.dts`` like the following:
> +
> +.. code-block::
> +
> + &sysclk {
> + assigned-clocks = <&sysclk K210_CLK_PLL0>;
> + assigned-clock-rates = <800000000>;
> + };
> +
> +There are three PLLs on the K210: PLL0 is the parent of most of the components,
> +including the CPU and RAM. PLL1 is the parent of the neural network coprocessor.
> +PLL2 is the parent of the sound processing devices. Note that child clocks of
> +PLL0 and PLL2 run at *half* the speed of the PLLs. For example, if PLL0 is
> +running at 800 MHz, then the CPU will run at 400 MHz. This is the example given
> +above. The CPU can be overclocked to around 600 MHz, and underclocked to 26 MHz.
> +
> +It is possible to set PLL2's parent to PLL0. The plls are more accurate when
> +converting between similar frequencies. This makes it easier to get an accurate
> +frequency for I2S. As an example, consider sampling an I2S device at 44.1 kHz.
> +On this device, the I2S serial clock runs at 64 times the sample rate.
> +Therefore, we would like to run PLL2 at an even multiple of 2.8224 MHz. If
> +PLL2's parent is IN0, we could use a frequency of 390 MHz (the same as the CPU's
> +default speed). Dividing by 138 yields a serial clock of about 2.8261 MHz. This
> +results in a sample rate of 44.158 kHz---around 50 Hz or .1% too fast. If,
> +instead, we set PLL2's parent to PLL1 running at 390 MHz, and request a rate of
> +2.8224 * 136 = 383.8464 MHz, the achieved rate is 383.90625 MHz. Dividing by 136
> +yields a serial clock of about 2.8228 MHz. This results in a sample rate of
> +44.107 kHz---just 7 Hz or .02% too fast. This configuration is shown in the
> +following example:
> +
> +.. code-block::
> +
> + &sysclk {
> + assigned-clocks = <&sysclk K210_CLK_PLL1>, <&sysclk K210_CLK_PLL2>;
> + assigned-clock-parents = <0>, <&sysclk K210_CLK_PLL1>;
> + assigned-clock-rates = <390000000>, <383846400>;
> + };
> +
> +There are a couple of quirks to the PLLs. First, there are more frequency ratios
> +just above and below 1.0, but there is a small gap around 1.0. To be explicit,
> +if the input frequency is 100 MHz, it would be impossible to have an output of
> +99 or 101 MHz. In addition, there is a maximum frequency for the internal VCO,
> +so higher input/output frequencies will be less accurate than lower ones.
> +
> +Technical Details
> +-----------------
> +
> +Boot Sequence
> +^^^^^^^^^^^^^
> +
> +1. ``RESET`` pin is deasserted.
> +2. Both harts begin executing at ``0x00001000``.
> +3. Both harts jump to firmware at ``0x88000000``.
> +4. One hart is chosen as a boot hart.
> +5. Firmware reads value of pin ``IO_16`` (ISP).
> +
> + * If the pin is low, enter ISP mode. This mode allows loading data to ram,
> + writing it to flash, and booting from specific addresses.
> + * If the pin is high, continue boot.
> +6. Firmware reads the next stage from flash (SPI3) to address ``0x80000000``.
> +
> + * If byte 0 is 1, the next stage is decrypted using the built-in AES
> + accelerator and the one-time programmable, 128-bit AES key.
> + * Bytes 1 to 4 hold the length of the next stage.
> + * The SHA-256 sum of the next stage is automatically calculated, and verified
> + against the 32 bytes following the next stage.
> +7. The boot hart sends an IPI to the other hart telling it to jump to the next
> + stage.
> +8. The boot hart jumps to ``0x80000000``.
> +
> +Memory Map
> +^^^^^^^^^^
> +
> +========== ========= ===========
> +Address Size Description
> +========== ========= ===========
> +0x00000000 0x1000 debug
> +0x00001000 0x1000 rom
> +0x02000000 0x1000 clint
> +0x0C000000 0x4000000 plic
> +0x38000000 0x1000 uarths
> +0x38001000 0x1000 gpiohs
> +0x40000000 0x400000 sram0 (non-cached)
> +0x40400000 0x200000 sram1 (non-cached)
> +0x40600000 0x200000 airam (non-cached)
> +0x40800000 0xC00000 kpu
> +0x42000000 0x400000 fft
> +0x50000000 0x1000 dmac
> +0x50200000 0x200000 apb0
> +0x50200000 0x80 gpio
> +0x50210000 0x100 uart0
> +0x50220000 0x100 uart1
> +0x50230000 0x100 uart2
> +0x50240000 0x100 spi slave
> +0x50250000 0x200 i2s0
> +0x50250200 0x200 apu
> +0x50260000 0x200 i2s1
> +0x50270000 0x200 i2s2
> +0x50280000 0x100 i2c0
> +0x50290000 0x100 i2c1
> +0x502A0000 0x100 i2c2
> +0x502B0000 0x100 fpioa
> +0x502C0000 0x100 sha256
> +0x502D0000 0x100 timer0
> +0x502E0000 0x100 timer1
> +0x502F0000 0x100 timer2
> +0x50400000 0x200000 apb1
> +0x50400000 0x100 wdt0
> +0x50410000 0x100 wdt1
> +0x50420000 0x100 otp control
> +0x50430000 0x100 dvp
> +0x50440000 0x100 sysctl
> +0x50450000 0x100 aes
> +0x50460000 0x100 rtc
> +0x52000000 0x4000000 apb2
> +0x52000000 0x100 spi0
> +0x53000000 0x100 spi1
> +0x54000000 0x200 spi3
> +0x80000000 0x400000 sram0 (cached)
> +0x80400000 0x200000 sram1 (cached)
> +0x80600000 0x200000 airam (cached)
> +0x88000000 0x20000 otp
> +0x88000000 0xC200 firmware
> +0x8801C000 0x1000 riscv priv spec 1.9 config
> +0x8801D000 0x2000 flattened device tree (contains only addresses and
> + interrupts)
> +0x8801f000 0x1000 credits
> +========== ========= ===========
> diff --git a/include/configs/sipeed-maix.h b/include/configs/sipeed-maix.h
> new file mode 100644
> index 0000000000..a46473fc78
> --- /dev/null
> +++ b/include/configs/sipeed-maix.h
> @@ -0,0 +1,24 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2019-20 Sean Anderson <seanga2 at gmail.com>
> + */
> +
> +#ifndef CONFIGS_SIPEED_MAIX_H
> +#define CONFIGS_SIPEED_MAIX_H
> +
> +#include <linux/sizes.h>
> +
> +#define CONFIG_SYS_LOAD_ADDR 0x80000000
> +/* Start just below the second bank so we don't clobber it during reloc */
> +#define CONFIG_SYS_INIT_SP_ADDR 0x803FFFFF
> +#define CONFIG_SYS_MALLOC_LEN SZ_128K
> +#define CONFIG_SYS_CACHELINE_SIZE 64
> +
> +#define CONFIG_SYS_SDRAM_BASE 0x80000000
> +/* Don't relocate into AI ram since it isn't set up yet */
> +#define CONFIG_SYS_SDRAM_SIZE (SZ_4M + SZ_2M)
> +
> +/* For early init */
> +#define K210_SYSCTL_BASE 0x50440000
> +
> +#endif /* CONFIGS_SIPEED_MAIX_H */
> --
> 2.25.0
>
More information about the U-Boot
mailing list