[PATCH v6 18/19] riscv: Add device tree for K210 and Sipeed Maix BitM
Rick Chen
rickchen36 at gmail.com
Tue Mar 10 10:08:48 CET 2020
Hi Sean
> Where possible, I have tried to find compatible drivers based on the layout
> of registers. However, many devices remain untested. All untested devices
> have been left disabled, but some tentative properties (such as compatible
> strings, and clocks, interrupts, and resets properties) have been added.
>
> Signed-off-by: Sean Anderson <seanga2 at gmail.com>
> ---
>
> Changes in v6:
> - Remove spi, gpio, pinmux, wdt, and led bindings
> - Use consistent capitalization for hex digits
>
> Changes in v5:
> - Add more compatible strings
> - Add cache line size
> - Document CPUs as rocket cores
> - Flesh out the gpio devices
> - Add ports for audio and video devices
> - Add fpioa pinctrl support
> - Configure pins for MMC on SPI1
> - Enable MMC
> - Fix a couple uart properties (Thanks laanwj)
> - Reorder ram now that relocation is handled with CONFIG_SYS defines
> - Enable WDT
> - Add pinctrl properties
> - Add gpio support
> - Add led support
> - Add assorted AV bindings
> - Add compatible strings for ram
> - Use GPIO-based CS for MMC
> - Limit SPI flash to 50 MHz
>
> Changes in v4:
> - Set regs sizes to full address range
> - Remove clock-frequency property from cpus
> - Add spi-max-frequency to spi devices from documentation
> - Add more compatible strings for each device
> - Add AI ram as a separate memory bank. Its clock is disabled on boot, and
> it cannot be accessed
> - Reorder memory banks so u-boot relocates higher, leaving more room to
> load boot images
> - Add designware ssi CTRL0 field shifts to spi devices
> - Don't enable the MMC slot
> - Update copyright
> - Lint
>
> Changes in v3:
> - Move this patch to the end of the series
> - Add a max frequency for spi3
> - Remov unused compatible strings from spi-flash at 0
> - Add s and u to isa string
> - Fix mmu-type
> - Remove cache-line size since it is unused (in u-boot) and undocumented
> (upstream)
> - Add timer interrupts to clint0
> - Round up various registers
> - Add riscv,max-priority to plic
> - Add apb* busses, since they have clocks which need to be enabled to
> access their devices
> - Change uart compatible strings to "snps,dw-apb-uart", since that appears
> to match their registers
> - Add compatible string for wdt*
> - Add system reset device under sysctl
> - Add reset device under sysctl
>
> Changes in v2:
> - Model changed to "Sipeed Maix Bit" to match file name
> - Value of stdout-path fixed
> - SD card slot compatible changed to "mmc-spi-slot"
> - "jedec,spi-nor" added to spi flash compatible list
> - Aliases for spi busses added
> - timebase-frequency divided by 50 to match timer speed
> - cpu-frequency renamed to clock-frequency
> - CPUX_intc restyled to cpuX_intc
> - "kendryte,k210-soc" added to soc compatible list for future-proofing
> - PLIC handle renamed to plic0 from pic0
> - K210_RST_SOC removed from sysrst, due to not being located in the reset
> register
> - K210_RST_* numbers changed to match their bit offset within the reset
> register
> - gpio_controller restyled to gpio-controller
> - Added a second clock to the dma binding to match what the driver expects
> - Changed "snps,designware-spi" compatible string to "snps,dw-apb-ssi" to
> match the correct driver
> - Added a name to the spi clocks
> - Added reg-io-width property to spi bindings
> - Assigned a default parent to K210_CLK_SPI3
> - Removed assigned clocks for ACLK and PLLs
> - Removed u-boot,dm-pre-reloc bindings
>
> arch/riscv/dts/Makefile | 1 +
> arch/riscv/dts/k210-maix-bit.dts | 47 ++
> arch/riscv/dts/k210.dtsi | 599 ++++++++++++++++++++++++
> include/dt-bindings/reset/k210-sysctl.h | 38 ++
It is not proper to mix them in one patch.
Thanks,
Rick
> 4 files changed, 685 insertions(+)
> create mode 100644 arch/riscv/dts/k210-maix-bit.dts
> create mode 100644 arch/riscv/dts/k210.dtsi
> create mode 100644 include/dt-bindings/reset/k210-sysctl.h
>
> diff --git a/arch/riscv/dts/Makefile b/arch/riscv/dts/Makefile
> index 4f30e6936f..3a6f96c67d 100644
> --- a/arch/riscv/dts/Makefile
> +++ b/arch/riscv/dts/Makefile
> @@ -2,6 +2,7 @@
>
> dtb-$(CONFIG_TARGET_AX25_AE350) += ae350_32.dtb ae350_64.dtb
> dtb-$(CONFIG_TARGET_SIFIVE_FU540) += hifive-unleashed-a00.dtb
> +dtb-$(CONFIG_TARGET_SIPEED_MAIX) += k210-maix-bit.dtb
>
> targets += $(dtb-y)
>
> diff --git a/arch/riscv/dts/k210-maix-bit.dts b/arch/riscv/dts/k210-maix-bit.dts
> new file mode 100644
> index 0000000000..5b32c5fd5f
> --- /dev/null
> +++ b/arch/riscv/dts/k210-maix-bit.dts
> @@ -0,0 +1,47 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2019-20 Sean Anderson <seanga2 at gmail.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "k210.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Sipeed Maix Bit 2.0";
> + compatible = "sipeed,maix-bitm", "sipeed,maix-bit", "kendryte,k210";
> +
> + chosen {
> + stdout-path = "serial0:115200";
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + status = "disabled";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&i2s0 0>;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&mic>;
> + };
> + };
> +
> + mic: mic {
> + #sound-dai-cells = <0>;
> + compatible = "memsensing,msm61s4030h0";
> + status = "disabled";
> + };
> +};
> +
> +&uarths0 {
> + status = "okay";
> +};
> +
> +&i2s0 {
> + #sound-dai-cells = <1>;
> +};
> diff --git a/arch/riscv/dts/k210.dtsi b/arch/riscv/dts/k210.dtsi
> new file mode 100644
> index 0000000000..8b3b872e2f
> --- /dev/null
> +++ b/arch/riscv/dts/k210.dtsi
> @@ -0,0 +1,599 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright (C) 2019-20 Sean Anderson <seanga2 at gmail.com>
> + */
> +
> +#include <dt-bindings/clock/k210-sysctl.h>
> +#include <dt-bindings/mfd/k210-sysctl.h>
> +#include <dt-bindings/reset/k210-sysctl.h>
> +
> +/ {
> + /*
> + * Although the K210 is a 64-bit CPU, the address bus is only 32-bits
> + * wide, and the upper half of all addresses is ignored.
> + */
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "kendryte,k210";
> +
> + aliases {
> + gpio0 = &gpio0;
> + gpio1 = &gpio1_0;
> + serial0 = &uarths0;
> + serial1 = &uart1;
> + serial2 = &uart2;
> + serial3 = &uart3;
> + spi0 = &spi0;
> + spi1 = &spi1;
> + spi2 = &spi2;
> + spi3 = &spi3;
> + };
> +
> + clocks {
> + in0: osc {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + };
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + timebase-frequency = <7800000>;
> + cpu0: cpu at 0 {
> + device_type = "cpu";
> + compatible = "kendryte,k210", "sifive,rocket0", "riscv";
> + reg = <0>;
> + riscv,isa = "rv64imafdgc";
> + mmu-type = "sv39";
> + i-cache-block-size = <64>;
> + i-cache-size = <0x8000>;
> + d-cache-block-size = <64>;
> + d-cache-size = <0x8000>;
> + clocks = <&sysclk K210_CLK_CPU>;
> + cpu0_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + compatible = "riscv,cpu-intc";
> + };
> + };
> + cpu1: cpu at 1 {
> + device_type = "cpu";
> + compatible = "kendryte,k210", "sifive,rocket0", "riscv";
> + reg = <1>;
> + riscv,isa = "rv64imafdgc";
> + mmu-type = "sv39";
> + i-cache-block-size = <64>;
> + i-cache-size = <0x8000>;
> + d-cache-block-size = <64>;
> + d-cache-size = <0x8000>;
> + clocks = <&sysclk K210_CLK_CPU>;
> + cpu1_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + interrupt-controller;
> + compatible = "riscv,cpu-intc";
> + };
> + };
> + };
> +
> + sram0: memory at 80000000 {
> + device_type = "memory";
> + compatible = "kendryte,k210-sram";
> + reg = <0x80000000 0x400000>;
> + clocks = <&sysclk K210_CLK_SRAM0>;
> + };
> +
> + sram1: memory at 80400000 {
> + device_type = "memory";
> + reg = <0x80400000 0x200000>;
> + compatible = "kendryte,k210-sram";
> + clocks = <&sysclk K210_CLK_SRAM1>;
> + };
> +
> + airam: memory at 80600000 {
> + device_type = "memory";
> + reg = <0x80600000 0x200000>;
> + compatible = "kendryte,k210-airam";
> + clocks = <&sysclk K210_CLK_PLL1>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + ai_reserved: ai at 80600000 {
> + reg = <0x80600000 0x200000>;
> + reusable;
> + };
> + };
> +
> + soc {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "kendryte,k210-soc", "simple-bus";
> + ranges;
> + interrupt-parent = <&plic0>;
> +
> + debug0: debug at 0 {
> + compatible = "kendryte,k210-debug", "riscv,debug";
> + reg = <0x0 0x1000>;
> + };
> +
> + rom0: nvmem at 1000 {
> + reg = <0x1000 0x1000>;
> + read-only;
> + };
> +
> + clint0: interrupt-controller at 2000000 {
> + #interrupt-cells = <1>;
> + compatible = "kendryte,k210-clint", "riscv,clint0";
> + reg = <0x2000000 0x1000>;
> + interrupt-controller;
> + interrupts-extended = <&cpu0_intc 3>, <&cpu0_intc 7>,
> + <&cpu1_intc 3>, <&cpu1_intc 7>;
> + clocks = <&sysclk K210_CLK_CPU>;
> + };
> +
> + plic0: interrupt-controller at C000000 {
> + #interrupt-cells = <1>;
> + compatible = "kendryte,k210-plic", "riscv,plic0";
> + reg = <0xC000000 0x4000000>;
> + interrupt-controller;
> + interrupts-extended = <&cpu0_intc 9>, <&cpu0_intc 11>,
> + <&cpu1_intc 9>, <&cpu1_intc 11>;
> + riscv,ndev = <65>;
> + riscv,max-priority = <7>;
> + };
> +
> + uarths0: serial at 38000000 {
> + compatible = "kendryte,k210-uarths", "sifive,uart0";
> + reg = <0x38000000 0x1000>;
> + interrupts = <33>;
> + clocks = <&sysclk K210_CLK_CPU>;
> + status = "disabled";
> + };
> +
> + gpio0: gpio-controller at 38001000 {
> + #interrupt-cells = <2>;
> + #gpio-cells = <2>;
> + compatible = "kendryte,k210-gpiohs", "sifive,gpio0";
> + reg = <0x38001000 0x1000>;
> + interrupt-controller;
> + interrupts = <34 35 36 37 38 39 40 41
> + 42 43 44 45 46 47 48 49
> + 50 51 52 53 54 55 56 57
> + 58 59 60 61 62 63 64 65>;
> + gpio-controller;
> + ngpios = <32>;
> + status = "disabled";
> + };
> +
> + kpu0: ai at 40800000 {
> + compatible = "kendryte,k210-ai";
> + reg = <0x40800000 0xc00000>;
> + interrupts = <25>;
> + clocks = <&sysclk K210_CLK_AI>;
> + memory-region = <&ai_reserved>;
> + status = "disabled";
> + };
> +
> + fft0: fft at 42000000 {
> + compatible = "kendryte,k210-fft";
> + reg = <0x42000000 0x400000>;
> + interrupts = <26>;
> + clocks = <&sysclk K210_CLK_FFT>;
> + resets = <&sysrst K210_RST_FFT>;
> + status = "disabled";
> + };
> +
> + dmac0: dma-controller at 50000000 {
> + compatible = "kendryte,k210-dmac", "snps,axi-dma-1.01a";
> + reg = <0x50000000 0x1000>;
> + interrupts = <27 28 29 30 31 32>;
> + clocks = <&sysclk K210_CLK_DMA>, <&sysclk K210_CLK_DMA>;
> + clock-names = "core-clk", "cfgr-clk";
> + resets = <&sysrst K210_RST_DMA>;
> + dma-channels = <6>;
> + snps,dma-masters = <2>;
> + snps,data-width = <5>;
> + snps,block-size = <0x400000 0x400000 0x400000
> + 0x400000 0x400000 0x400000>;
> + snps,axi-max-burst-len = <256>;
> + status = "disabled";
> + };
> +
> + apb0: bus at 50200000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "kendryte,k210-apb", "simple-pm-bus";
> + ranges;
> + clocks = <&sysclk K210_CLK_APB0>;
> +
> + gpio1: gpio-controller at 50200000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "kendryte,k210-gpio",
> + "snps,dw-apb-gpio";
> + reg = <0x50200000 0x80>;
> + clocks = <&sysclk K210_CLK_GPIO>;
> + resets = <&sysrst K210_RST_GPIO>;
> + status = "disabled";
> +
> + gpio1_0: gpio1 at 0 {
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + compatible = "snps,dw-apb-gpio-port";
> + reg = <0>;
> + interrupt-controller;
> + interrupts = <23>;
> + gpio-controller;
> + snps,nr-gpios = <8>;
> + };
> + };
> +
> + uart1: serial at 50210000 {
> + compatible = "kendryte,k210-uart",
> + "snps,dw-apb-uart";
> + reg = <0x50210000 0x100>;
> + interrupts = <11>;
> + clocks = <&sysclk K210_CLK_UART1>;
> + resets = <&sysrst K210_RST_UART1>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + dcd-override;
> + dsr-override;
> + cts-override;
> + ri-override;
> + status = "disabled";
> + };
> +
> + uart2: serial at 50220000 {
> + compatible = "kendryte,k210-uart",
> + "snps,dw-apb-uart";
> + reg = <0x50220000 0x100>;
> + interrupts = <12>;
> + clocks = <&sysclk K210_CLK_UART2>;
> + resets = <&sysrst K210_RST_UART2>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + dcd-override;
> + dsr-override;
> + cts-override;
> + ri-override;
> + status = "disabled";
> + };
> +
> + uart3: serial at 50230000 {
> + compatible = "kendryte,k210-uart",
> + "snps,dw-apb-uart";
> + reg = <0x50230000 0x100>;
> + interrupts = <13>;
> + clocks = <&sysclk K210_CLK_UART3>;
> + resets = <&sysrst K210_RST_UART3>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + dcd-override;
> + dsr-override;
> + cts-override;
> + ri-override;
> + status = "disabled";
> + };
> +
> + spi2: spi at 50240000 {
> + compatible = "kendryte,k120-spislave",
> + "snps,dw-apb-ssi";
> + spi-slave;
> + reg = <0x50240000 0x100>;
> + interrupts = <2>;
> + clocks = <&sysclk K210_CLK_SPI2>;
> + resets = <&sysrst K210_RST_SPI2>;
> + spi-max-frequency = <25000000>;
> + /*
> + * Likely not the only offset change, but this
> + * is the only one which is documented.
> + */
> + snps,tmod-offset = <8>;
> + status = "disabled";
> + };
> +
> + i2s0: i2s at 50250000 {
> + compatible = "kendryte,k210-i2s",
> + "snps,designware-i2s";
> + reg = <0x50250000 0x200>;
> + interrupts = <5>;
> + clocks = <&sysclk K210_CLK_I2S0>;
> + clock-names = "i2sclk";
> + resets = <&sysrst K210_RST_I2S0>;
> + status = "disabled";
> + };
> +
> + apu0: sound at 520250200 {
> + compatible = "kendryte,k210-apu";
> + reg = <0x50250200 0x200>;
> + status = "disabled";
> + };
> +
> + i2s1: i2s at 50260000 {
> + compatible = "kendryte,k210-i2s",
> + "snps,designware-i2s";
> + reg = <0x50260000 0x200>;
> + interrupts = <6>;
> + clocks = <&sysclk K210_CLK_I2S1>;
> + clock-names = "i2sclk";
> + resets = <&sysrst K210_RST_I2S1>;
> + status = "disabled";
> + };
> +
> + i2s2: i2s at 50270000 {
> + compatible = "kendryte,k210-i2s",
> + "snps,designware-i2s";
> + reg = <0x50270000 0x200>;
> + interrupts = <7>;
> + clocks = <&sysclk K210_CLK_I2S2>;
> + clock-names = "i2sclk";
> + resets = <&sysrst K210_RST_I2S2>;
> + status = "disabled";
> + };
> +
> + i2c0: i2c at 50280000 {
> + compatible = "kendryte,k210-i2c",
> + "snps,designware-i2c";
> + reg = <0x50280000 0x100>;
> + interrupts = <8>;
> + clocks = <&sysclk K210_CLK_I2C0>;
> + resets = <&sysrst K210_RST_I2C0>;
> + status = "disabled";
> + };
> +
> + i2c1: i2c at 50290000 {
> + compatible = "kendryte,k210-i2c",
> + "snps,designware-i2c";
> + reg = <0x50290000 0x100>;
> + interrupts = <9>;
> + clocks = <&sysclk K210_CLK_I2C1>;
> + resets = <&sysrst K210_RST_I2C1>;
> + status = "disabled";
> + };
> +
> + i2c2: i2c at 502A0000 {
> + compatible = "kendryte,k210-i2c",
> + "snps,designware-i2c";
> + reg = <0x502A0000 0x100>;
> + interrupts = <10>;
> + clocks = <&sysclk K210_CLK_I2C2>;
> + resets = <&sysrst K210_RST_I2C2>;
> + status = "disabled";
> + };
> +
> + fpioa: pinmux at 502B0000 {
> + compatible = "kendryte,k210-fpioa";
> + reg = <0x502B0000 0x100>;
> + clocks = <&sysclk K210_CLK_FPIOA>;
> + resets = <&sysrst K210_RST_FPIOA>;
> + status = "disabled";
> + };
> +
> + sha256: sha256 at 502C0000 {
> + compatible = "kendryte,k210-sha256";
> + reg = <0x502C0000 0x100>;
> + clocks = <&sysclk K210_CLK_SHA>;
> + resets = <&sysrst K210_RST_SHA>;
> + status = "disabled";
> + };
> +
> + timer0: timer at 502D0000 {
> + compatible = "kendryte,k210-timer",
> + "snps,dw-apb-timer";
> + reg = <0x502D0000 0x100>;
> + interrupts = <14 15>;
> + clocks = <&sysclk K210_CLK_TIMER0>;
> + clock-names = "timer";
> + resets = <&sysrst K210_RST_TIMER0>;
> + status = "disabled";
> + };
> +
> + timer1: timer at 502E0000 {
> + compatible = "kendryte,k210-timer",
> + "snps,dw-apb-timer";
> + reg = <0x502E0000 0x100>;
> + interrupts = <16 17>;
> + clocks = <&sysclk K210_CLK_TIMER1>;
> + clock-names = "timer";
> + resets = <&sysrst K210_RST_TIMER1>;
> + status = "disabled";
> + };
> +
> + timer2: timer at 502F0000 {
> + compatible = "kendryte,k210-timer",
> + "snps,dw-apb-timer";
> + reg = <0x502F0000 0x100>;
> + interrupts = <18 19>;
> + clocks = <&sysclk K210_CLK_TIMER2>;
> + clock-names = "timer";
> + resets = <&sysrst K210_RST_TIMER2>;
> + status = "disabled";
> + };
> + };
> +
> + apb1: bus at 50400000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "kendryte,k210-apb", "simple-pm-bus";
> + ranges;
> + clocks = <&sysclk K210_CLK_APB1>;
> +
> + wdt0: watchdog at 50400000 {
> + compatible = "kendryte,k210-wdt", "snps,dw-wdt";
> + reg = <0x50400000 0x100>;
> + interrupts = <21>;
> + clocks = <&sysclk K210_CLK_WDT0>;
> + resets = <&sysrst K210_RST_WDT0>;
> + status = "disabled";
> + };
> +
> + wdt1: watchdog at 50410000 {
> + compatible = "kendryte,k210-wdt", "snps,dw-wdt";
> + reg = <0x50410000 0x100>;
> + interrupts = <22>;
> + clocks = <&sysclk K210_CLK_WDT1>;
> + resets = <&sysrst K210_RST_WDT1>;
> + status = "disabled";
> + };
> +
> + otp0: nvmem at 50420000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "kendryte,k210-otp";
> + reg = <0x50420000 0x100>,
> + <0x88000000 0x20000>;
> + reg-names = "reg", "mem";
> + clocks = <&sysclk K210_CLK_ROM>;
> + resets = <&sysrst K210_RST_ROM>;
> + read-only;
> + status = "disabled";
> +
> + /* Bootloader */
> + firmware at 00000 {
> + reg = <0x00000 0xC200>;
> + };
> +
> + /*
> + * config string as described in RISC-V
> + * privileged spec 1.9
> + */
> + config-1-9 at 1c000 {
> + reg = <0x1C000 0x1000>;
> + };
> +
> + /*
> + * Device tree containing only registers,
> + * interrupts, and cpus
> + */
> + fdt at 1d000 {
> + reg = <0x1D000 0x2000>;
> + };
> +
> + /* CPU/ROM credits */
> + credits at 1f000 {
> + reg = <0x1F000 0x1000>;
> + };
> + };
> +
> + dvp0: camera at 50430000 {
> + compatible = "kendryte,k210-dvp";
> + reg = <0x50430000 0x100>;
> + interrupts = <24>;
> + clocks = <&sysclk K210_CLK_DVP>;
> + resets = <&sysrst K210_RST_DVP>;
> + status = "disabled";
> + };
> +
> + sysctl: syscon at 50440000 {
> + compatible = "kendryte,k210-sysctl",
> + "syscon", "simple-mfd";
> + reg = <0x50440000 0x100>;
> + reg-io-width = <4>;
> +
> + sysclk: clock-controller {
> + #clock-cells = <1>;
> + compatible = "kendryte,k210-clk";
> + clocks = <&in0>;
> + };
> +
> + sysrst: reset-controller {
> + compatible = "kendryte,k210-rst",
> + "syscon-reset";
> + #reset-cells = <1>;
> + regmap = <&sysctl>;
> + offset = <K210_SYSCTL_PERI_RESET>;
> + mask = <0x27FFFFFF>;
> + assert-high = <1>;
> + };
> +
> + reboot {
> + compatible = "syscon-reboot";
> + regmap = <&sysctl>;
> + offset = <K210_SYSCTL_SOFT_RESET>;
> + mask = <1>;
> + value = <1>;
> + };
> + };
> +
> + aes0: aes at 50450000 {
> + compatible = "kendryte,k210-aes";
> + reg = <0x50450000 0x100>;
> + clocks = <&sysclk K210_CLK_AES>;
> + resets = <&sysrst K210_RST_AES>;
> + status = "disabled";
> + };
> +
> + rtc: rtc at 50460000 {
> + compatible = "kendryte,k210-rtc";
> + reg = <0x50460000 0x100>;
> + clocks = <&in0>;
> + resets = <&sysrst K210_RST_RTC>;
> + interrupts = <20>;
> + status = "disabled";
> + };
> + };
> +
> + apb2: bus at 52000000 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "kendryte,k210-apb", "simple-pm-bus";
> + ranges;
> + clocks = <&sysclk K210_CLK_APB2>;
> +
> + spi0: spi at 52000000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "kendryte,k210-spi",
> + "snps,dw-apb-ssi";
> + reg = <0x52000000 0x100>;
> + interrupts = <1>;
> + clocks = <&sysclk K210_CLK_SPI0>;
> + clock-names = "ssi_clk";
> + resets = <&sysrst K210_RST_SPI0>;
> + spi-max-frequency = <25000000>;
> + num-cs = <4>;
> + reg-io-width = <4>;
> + status = "disabled";
> + };
> +
> + spi1: spi at 53000000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "kendryte,k210-spi",
> + "snps,dw-apb-ssi";
> + reg = <0x53000000 0x100>;
> + interrupts = <2>;
> + clocks = <&sysclk K210_CLK_SPI1>;
> + clock-names = "ssi_clk";
> + resets = <&sysrst K210_RST_SPI1>;
> + spi-max-frequency = <25000000>;
> + num-cs = <4>;
> + reg-io-width = <4>;
> + status = "disabled";
> + };
> +
> + spi3: spi at 54000000 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "kendryte,k210-spi",
> + "snps,dw-apb-ssi";
> + reg = <0x54000000 0x200>;
> + interrupts = <4>;
> + clocks = <&sysclk K210_CLK_SPI3>;
> + clock-names = "ssi_clk";
> + resets = <&sysrst K210_RST_SPI3>;
> + /* Could possibly go up to 200 MHz */
> + spi-max-frequency = <100000000>;
> + num-cs = <4>;
> + reg-io-width = <4>;
> + status = "disabled";
> + };
> + };
> + };
> +};
> diff --git a/include/dt-bindings/reset/k210-sysctl.h b/include/dt-bindings/reset/k210-sysctl.h
> new file mode 100644
> index 0000000000..12bb3880d9
> --- /dev/null
> +++ b/include/dt-bindings/reset/k210-sysctl.h
> @@ -0,0 +1,38 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2019 Sean Anderson <seanga2 at gmail.com>
> + */
> +
> +#ifndef RESET_K210_SYSCTL_H
> +#define RESET_K210_SYSCTL_H
> +
> +#define K210_RST_ROM 0
> +#define K210_RST_DMA 1
> +#define K210_RST_AI 2
> +#define K210_RST_DVP 3
> +#define K210_RST_FFT 4
> +#define K210_RST_GPIO 5
> +#define K210_RST_SPI0 6
> +#define K210_RST_SPI1 7
> +#define K210_RST_SPI2 8
> +#define K210_RST_SPI3 9
> +#define K210_RST_I2S0 10
> +#define K210_RST_I2S1 11
> +#define K210_RST_I2S2 12
> +#define K210_RST_I2C0 13
> +#define K210_RST_I2C1 14
> +#define K210_RST_I2C2 15
> +#define K210_RST_UART1 16
> +#define K210_RST_UART2 17
> +#define K210_RST_UART3 18
> +#define K210_RST_AES 19
> +#define K210_RST_FPIOA 20
> +#define K210_RST_TIMER0 21
> +#define K210_RST_TIMER1 22
> +#define K210_RST_TIMER2 23
> +#define K210_RST_WDT0 24
> +#define K210_RST_WDT1 25
> +#define K210_RST_SHA 26
> +#define K210_RST_RTC 29
> +
> +#endif /* RESET_K210_SYSCTL_H */
> --
> 2.25.0
>
More information about the U-Boot
mailing list