[PATCH 01/14] drivers: net: add Layerscape mEMAC MDIO driver

Priyanka Jain (OSS) priyanka.jain at oss.nxp.com
Wed Mar 18 12:53:01 CET 2020 

>-----Original Message-----
>From: U-Boot <u-boot-bounces at lists.denx.de> On Behalf Of Ioana Ciornei
>Sent: Thursday, March 12, 2020 9:36 PM
>To: Priyanka Jain <priyanka.jain at nxp.com>; joe.hershberger at ni.com; u-
>boot at lists.denx.de
>Cc: Florin Laurentiu Chiculita <florinlaurentiu.chiculita at nxp.com>; Madalin
>Bucur (OSS) <madalin.bucur at oss.nxp.com>; Ioana Ciornei
><ioana.ciornei at nxp.com>
>Subject: [PATCH 01/14] drivers: net: add Layerscape mEMAC MDIO driver
>
>Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate
>Ethernet Media Access Controller) and the Fman 10G Ethernet MACs.
>
>Signed-off-by: Ioana Ciornei <ioana.ciornei at nxp.com>
>---
> drivers/net/Kconfig       |   7 ++
> drivers/net/Makefile      |   1 +
> drivers/net/fsl_ls_mdio.c | 158 ++++++++++++++++++++++++++++++++++++++
> 3 files changed, 166 insertions(+)
> create mode 100644 drivers/net/fsl_ls_mdio.c
>
>diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index
>4d1013c98466..bc518f218da6 100644
>--- a/drivers/net/Kconfig
>+++ b/drivers/net/Kconfig
>@@ -640,4 +640,11 @@ config MVMDIO
>
> 	  This driver is used by the MVPP2 and MVNETA drivers.
>
>+config FSL_LS_MDIO
Please use prefix NXP for new configs
>+	bool "NXP Layerscape MDIO interface support"
>+	depends on DM_MDIO
>+	help
>+	  This driver supports the MDIO bus found on the Fman 10G Ethernet
>MACs and
>+	  on the mEMAC (which supports both Clauses 22 and 45).
>+
> endif # NETDEVICES
>diff --git a/drivers/net/Makefile b/drivers/net/Makefile index
>6e0a68834d97..6d9b8772b1a5 100644
>--- a/drivers/net/Makefile
>+++ b/drivers/net/Makefile
>@@ -83,3 +83,4 @@ obj-y += mscc_eswitch/
> obj-$(CONFIG_HIGMACV300_ETH) += higmacv300.o
> obj-$(CONFIG_MDIO_SANDBOX) += mdio_sandbox.o
> obj-$(CONFIG_FSL_ENETC) += fsl_enetc.o fsl_enetc_mdio.o
>+obj-$(CONFIG_FSL_LS_MDIO) += fsl_ls_mdio.o
>diff --git a/drivers/net/fsl_ls_mdio.c b/drivers/net/fsl_ls_mdio.c new file mode
>100644 index 000000000000..845c0ac1ffd8
>--- /dev/null
>+++ b/drivers/net/fsl_ls_mdio.c
>@@ -0,0 +1,158 @@
>+// SPDX-License-Identifier: GPL-2.0+
>+/*
>+ * Copyright 2020 NXP
>+ */
>+
>+#include <common.h>
>+#include <dm.h>
>+#include <errno.h>
>+#include <miiphy.h>
>+#include <asm/io.h>
>+#include <fsl_memac.h>
>+
>+#ifdef CONFIG_SYS_MEMAC_LITTLE_ENDIAN
>+#define memac_out_32(a, v)	out_le32(a, v)
>+#define memac_clrbits_32(a, v)	clrbits_le32(a, v)
>+#define memac_setbits_32(a, v)	setbits_le32(a, v)
>+#else
>+#define memac_out_32(a, v)	out_be32(a, v)
>+#define memac_clrbits_32(a, v)	clrbits_be32(a, v)
>+#define memac_setbits_32(a, v)	setbits_be32(a, v)
>+#endif
>+
>+static u32 memac_in_32(u32 *reg)
>+{
>+#ifdef CONFIG_SYS_MEMAC_LITTLE_ENDIAN
>+	return in_le32(reg);
>+#else
>+	return in_be32(reg);
>+#endif
>+}
>+
>+struct fsl_ls_mdio_priv {
>+	void *regs_base;
>+};
>+
>+static int dm_fsl_ls_mdio_read(struct udevice *dev, int addr,
>+			       int devad, int reg)
>+{
>+	struct fsl_ls_mdio_priv *priv = dev_get_priv(dev);
>+	struct memac_mdio_controller *regs;
>+	u32 mdio_ctl;
>+	u32 c45 = 1;
>+
>+	regs = (struct memac_mdio_controller *)(priv->regs_base);
>+	if (devad == MDIO_DEVAD_NONE) {
>+		c45 = 0; /* clause 22 */
>+		devad = reg & 0x1f;
I don't see devad getting used in below code. 
>+		memac_clrbits_32(&regs->mdio_stat, MDIO_STAT_ENC);
>+	} else {
>+		memac_setbits_32(&regs->mdio_stat, MDIO_STAT_ENC);
>+	}
>+
>+	/* Wait till the bus is free */
>+	while ((memac_in_32(&regs->mdio_stat)) & MDIO_STAT_BSY)
>+		;
>+
>+	/* Set the Port and Device Addrs */
>+	mdio_ctl = MDIO_CTL_PORT_ADDR(addr) |
>MDIO_CTL_DEV_ADDR(devad);
>+	memac_out_32(&regs->mdio_ctl, mdio_ctl);
>+
>+	/* Set the register address */
>+	if (c45)
>+		memac_out_32(&regs->mdio_addr, reg & 0xffff);
>+
>+	/* Wait till the bus is free */
>+	while ((memac_in_32(&regs->mdio_stat)) & MDIO_STAT_BSY)
>+		;
>+
>+	/* Initiate the read */
>+	mdio_ctl |= MDIO_CTL_READ;
>+	memac_out_32(&regs->mdio_ctl, mdio_ctl);
>+
>+	/* Wait till the MDIO write is complete */
>+	while ((memac_in_32(&regs->mdio_data)) & MDIO_DATA_BSY)
>+		;
>+
>+	/* Return all Fs if nothing was there */
>+	if (memac_in_32(&regs->mdio_stat) & MDIO_STAT_RD_ER)
>+		return 0xffff;
>+
>+	return memac_in_32(&regs->mdio_data) & 0xffff;
>+	return 0;
>+}
>+
>+static int dm_fsl_ls_mdio_write(struct udevice *dev, int addr, int devad,
>+				int reg, u16 val)
>+{
>+	struct fsl_ls_mdio_priv *priv = dev_get_priv(dev);
>+	struct memac_mdio_controller *regs;
>+	u32 mdio_ctl;
>+	u32 c45 = 1;
>+
>+	regs = (struct memac_mdio_controller *)(priv->regs_base);
>+	if (devad == MDIO_DEVAD_NONE) {
>+		c45 = 0; /* clause 22 */
>+		devad = reg & 0x1f;
Sane commen as above
>+		memac_clrbits_32(&regs->mdio_stat, MDIO_STAT_ENC);
>+	} else {
>+		memac_setbits_32(&regs->mdio_stat, MDIO_STAT_ENC);
>+	}
>+
>+	/* Wait till the bus is free */
>+	while ((memac_in_32(&regs->mdio_stat)) & MDIO_STAT_BSY)
>+		;
>+
>+	/* Set the port and dev addr */
>+	mdio_ctl = MDIO_CTL_PORT_ADDR(addr) |
>MDIO_CTL_DEV_ADDR(devad);
>+	memac_out_32(&regs->mdio_ctl, mdio_ctl);
>+
>+	/* Set the register address */
>+	if (c45)
>+		memac_out_32(&regs->mdio_addr, reg & 0xffff);
>+
>+	/* Wait till the bus is free */
>+	while ((memac_in_32(&regs->mdio_stat)) & MDIO_STAT_BSY)
>+		;
>+
>+	/* Write the value to the register */
>+	memac_out_32(&regs->mdio_data, MDIO_DATA(val));
>+
>+	/* Wait till the MDIO write is complete */
>+	while ((memac_in_32(&regs->mdio_data)) & MDIO_DATA_BSY)
>+		;
>+
>+	return 0;
>+}
>+
>+static const struct mdio_ops fsl_ls_mdio_ops = {
>+	.read = dm_fsl_ls_mdio_read,
>+	.write = dm_fsl_ls_mdio_write,
>+};
>+
>+static int fsl_ls_mdio_probe(struct udevice *dev) {
>+	struct fsl_ls_mdio_priv *priv = dev_get_priv(dev);
>+	struct memac_mdio_controller *regs;
>+
>+	priv->regs_base = dev_read_addr_ptr(dev);
>+	regs = (struct memac_mdio_controller *)(priv->regs_base);
>+
>+	memac_setbits_32(&regs->mdio_stat,
>+			 MDIO_STAT_CLKDIV(258) | MDIO_STAT_NEG);
>+
>+	return 0;
>+}
>+
>+static const struct udevice_id fsl_ls_mdio_of_ids[] = {
>+	{ .compatible = "fsl,ls-mdio" },
>+};
>+
>+U_BOOT_DRIVER(fsl_ls_mdio) = {
>+	.name = "fsl_ls_mdio",
>+	.id = UCLASS_MDIO,
>+	.of_match = fsl_ls_mdio_of_ids,
>+	.probe = fsl_ls_mdio_probe,
>+	.ops = &fsl_ls_mdio_ops,
>+	.priv_auto_alloc_size = sizeof(struct fsl_ls_mdio_priv), };
>--
>2.17.1

Regards
Priyanka

More information about the U-Boot mailing list