[PATCH] ARM: dts: stm32: Split AV96 into DHCOR SoM and AV96 board
Patrice CHOTARD
patrice.chotard at st.com
Mon Mar 30 14:32:39 CEST 2020
Hi Marek
On 3/27/20 12:42 AM, Marek Vasut wrote:
> The AV96 is in fact an assembly of DH Electronics DHCOR SoM on top
> of an AV96 reference board. Split the DTs to reflect that and make
> sure to DHCOR SoM can be reused on other boards easily.
>
> It is also highly recommended to configure the board for the DHCOM
> make stm32mp15_dhcom_basic_defconfig
> make DEVICE_TREE=stm32mp15xx-dhcor-avenger96
> as that permits reusing the board code for the DH components, like
> accessing and reading out the ethernet MAC from EEPROM.
>
> Signed-off-by: Marek Vasut <marex at denx.de>
> Cc: Patrick Delaunay <patrick.delaunay at st.com>
> Cc: Patrice Chotard <patrice.chotard at st.com>
> ---
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/stm32mp157a-avenger96.dts | 393 +-----------------
> .../stm32mp15xx-dhcor-avenger96-u-boot.dtsi | 80 ++++
> arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts | 196 +++++++++
> ...oot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} | 79 +---
> arch/arm/dts/stm32mp15xx-dhcor.dtsi | 220 ++++++++++
> doc/board/st/stm32mp1.rst | 8 +-
> 7 files changed, 509 insertions(+), 470 deletions(-)
> create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
> create mode 100644 arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
> rename arch/arm/dts/{stm32mp157a-avenger96-u-boot.dtsi => stm32mp15xx-dhcor-u-boot.dtsi} (75%)
> create mode 100644 arch/arm/dts/stm32mp15xx-dhcor.dtsi
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 9c593b2c98..2564f790de 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -884,7 +884,8 @@ dtb-$(CONFIG_STM32MP15x) += \
> stm32mp157c-dk2.dtb \
> stm32mp157c-ed1.dtb \
> stm32mp157c-ev1.dtb \
> - stm32mp15xx-dhcom-pdk2.dtb
> + stm32mp15xx-dhcom-pdk2.dtb \
> + stm32mp15xx-dhcor-avenger96.dtb
>
> dtb-$(CONFIG_SOC_K3_AM6) += k3-am654-base-board.dtb k3-am654-r5-base-board.dtb
> dtb-$(CONFIG_SOC_K3_J721E) += k3-j721e-common-proc-board.dtb \
> diff --git a/arch/arm/dts/stm32mp157a-avenger96.dts b/arch/arm/dts/stm32mp157a-avenger96.dts
> index 8e36df8787..9c165104fb 100644
> --- a/arch/arm/dts/stm32mp157a-avenger96.dts
> +++ b/arch/arm/dts/stm32mp157a-avenger96.dts
> @@ -4,394 +4,5 @@
> * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> */
>
> -/dts-v1/;
> -
> -#include "stm32mp157c.dtsi"
> -#include "stm32mp157xac-pinctrl.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/mfd/st,stpmic1.h>
> -
> -/ {
> - model = "Arrow Electronics STM32MP157A Avenger96 board";
> - compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
> -
> - aliases {
> - ethernet0 = ðernet0;
> - mmc0 = &sdmmc1;
> - serial0 = &uart4;
> - serial1 = &uart7;
> - spi0 = &qspi;
> - };
> -
> - chosen {
> - stdout-path = "serial0:115200n8";
> - };
> -
> - memory at c0000000 {
> - device_type = "memory";
> - reg = <0xc0000000 0x40000000>;
> - };
> -
> - led {
> - compatible = "gpio-leds";
> - led1 {
> - label = "green:user1";
> - gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "heartbeat";
> - default-state = "off";
> - };
> -
> - led2 {
> - label = "green:user2";
> - gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "mmc0";
> - default-state = "off";
> - };
> -
> - led3 {
> - label = "green:user3";
> - gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "mmc1";
> - default-state = "off";
> - };
> -
> - led4 {
> - label = "green:user3";
> - gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "none";
> - default-state = "off";
> - panic-indicator;
> - };
> -
> - led5 {
> - label = "yellow:wifi";
> - gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "phy0tx";
> - default-state = "off";
> - };
> -
> - led6 {
> - label = "blue:bt";
> - gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "bluetooth-power";
> - default-state = "off";
> - };
> - };
> -};
> -
> -ðernet0 {
> - status = "okay";
> - pinctrl-0 = <ðernet0_rgmii_pins_b>;
> - pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
> - pinctrl-names = "default", "sleep";
> - phy-mode = "rgmii";
> - max-speed = <1000>;
> - phy-handle = <&phy0>;
> - phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
> -
> - mdio0 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "snps,dwmac-mdio";
> - phy0: ethernet-phy at 7 {
> - reg = <7>;
> - };
> - };
> -};
> -
> -&i2c1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c1_pins_b>;
> - i2c-scl-rising-time-ns = <185>;
> - i2c-scl-falling-time-ns = <20>;
> - status = "okay";
> - /delete-property/dmas;
> - /delete-property/dma-names;
> -};
> -
> -&i2c2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
> - i2c-scl-rising-time-ns = <185>;
> - i2c-scl-falling-time-ns = <20>;
> - status = "okay";
> - /delete-property/dmas;
> - /delete-property/dma-names;
> -};
> -
> -&i2c4 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c4_pins_a>;
> - i2c-scl-rising-time-ns = <185>;
> - i2c-scl-falling-time-ns = <20>;
> - status = "okay";
> - /delete-property/dmas;
> - /delete-property/dma-names;
> -
> - pmic: stpmic at 33 {
> - compatible = "st,stpmic1";
> - reg = <0x33>;
> - interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - status = "okay";
> -
> - st,main-control-register = <0x04>;
> - st,vin-control-register = <0xc0>;
> - st,usb-control-register = <0x30>;
> -
> - regulators {
> - compatible = "st,stpmic1-regulators";
> -
> - ldo1-supply = <&v3v3>;
> - ldo2-supply = <&v3v3>;
> - ldo3-supply = <&vdd_ddr>;
> - ldo5-supply = <&v3v3>;
> - ldo6-supply = <&v3v3>;
> - pwr_sw1-supply = <&bst_out>;
> - pwr_sw2-supply = <&bst_out>;
> -
> - vddcore: buck1 {
> - regulator-name = "vddcore";
> - regulator-min-microvolt = <800000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-always-on;
> - regulator-initial-mode = <0>;
> - regulator-over-current-protection;
> - };
> -
> - vdd_ddr: buck2 {
> - regulator-name = "vdd_ddr";
> - regulator-min-microvolt = <1350000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-always-on;
> - regulator-initial-mode = <0>;
> - regulator-over-current-protection;
> - };
> -
> - vdd: buck3 {
> - regulator-name = "vdd";
> - regulator-min-microvolt = <2500000>;
> - regulator-max-microvolt = <2500000>;
> - regulator-always-on;
> - st,mask_reset;
> - regulator-initial-mode = <0>;
> - regulator-over-current-protection;
> - };
> -
> - v3v3: buck4 {
> - regulator-name = "v3v3";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - regulator-over-current-protection;
> - regulator-initial-mode = <0>;
> - };
> -
> - vdda: ldo1 {
> - regulator-name = "vdda";
> - regulator-min-microvolt = <2900000>;
> - regulator-max-microvolt = <2900000>;
> - interrupts = <IT_CURLIM_LDO1 0>;
> - interrupt-parent = <&pmic>;
> - };
> -
> - v2v8: ldo2 {
> - regulator-name = "v2v8";
> - regulator-min-microvolt = <2800000>;
> - regulator-max-microvolt = <2800000>;
> - interrupts = <IT_CURLIM_LDO2 0>;
> - interrupt-parent = <&pmic>;
> - };
> -
> - vtt_ddr: ldo3 {
> - regulator-name = "vtt_ddr";
> - regulator-min-microvolt = <0>;
> - regulator-max-microvolt = <1000000>;
> - regulator-always-on;
> - regulator-over-current-protection;
> - };
> -
> - vdd_usb: ldo4 {
> - regulator-name = "vdd_usb";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - interrupts = <IT_CURLIM_LDO4 0>;
> - interrupt-parent = <&pmic>;
> - };
> -
> - vdd_sd: ldo5 {
> - regulator-name = "vdd_sd";
> - regulator-min-microvolt = <2900000>;
> - regulator-max-microvolt = <2900000>;
> - interrupts = <IT_CURLIM_LDO5 0>;
> - interrupt-parent = <&pmic>;
> - regulator-boot-on;
> - };
> -
> - v1v8: ldo6 {
> - regulator-name = "v1v8";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - interrupts = <IT_CURLIM_LDO6 0>;
> - interrupt-parent = <&pmic>;
> - regulator-enable-ramp-delay = <300000>;
> - };
> -
> - vref_ddr: vref_ddr {
> - regulator-name = "vref_ddr";
> - regulator-always-on;
> - regulator-over-current-protection;
> - };
> -
> - bst_out: boost {
> - regulator-name = "bst_out";
> - interrupts = <IT_OCP_BOOST 0>;
> - interrupt-parent = <&pmic>;
> - };
> -
> - vbus_otg: pwr_sw1 {
> - regulator-name = "vbus_otg";
> - interrupts = <IT_OCP_OTG 0>;
> - interrupt-parent = <&pmic>;
> - regulator-active-discharge = <1>;
> - };
> -
> - vbus_sw: pwr_sw2 {
> - regulator-name = "vbus_sw";
> - interrupts = <IT_OCP_SWOUT 0>;
> - interrupt-parent = <&pmic>;
> - regulator-active-discharge = <1>;
> - };
> - };
> -
> - onkey {
> - compatible = "st,stpmic1-onkey";
> - interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
> - interrupt-names = "onkey-falling", "onkey-rising";
> - status = "okay";
> - };
> -
> - watchdog {
> - compatible = "st,stpmic1-wdt";
> - status = "disabled";
> - };
> - };
> -
> - eeprom at 53 {
> - compatible = "atmel,24c02";
> - reg = <0x53>;
> - pagesize = <16>;
> - };
> -};
> -
> -&iwdg2 {
> - timeout-sec = <32>;
> - status = "okay";
> -};
> -
> -&pwr_regulators {
> - vdd-supply = <&vdd>;
> - vdd_3v3_usbfs-supply = <&vdd_usb>;
> -};
> -
> -&qspi {
> - pinctrl-names = "default", "sleep";
> - pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
> - pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
> - reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - status = "okay";
> -
> - flash0: mx66l51235l at 0 {
> - compatible = "jedec,spi-nor";
> - reg = <0>;
> - spi-rx-bus-width = <4>;
> - spi-max-frequency = <108000000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - };
> -};
> -
> -&rng1 {
> - status = "okay";
> -};
> -
> -&rtc {
> - status = "okay";
> -};
> -
> -&sdmmc1 {
> - pinctrl-names = "default", "opendrain", "sleep";
> - pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> - pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> - pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> - broken-cd;
> - st,sig-dir;
> - st,neg-edge;
> - st,use-ckin;
> - bus-width = <4>;
> - vmmc-supply = <&vdd_sd>;
> - status = "okay";
> -};
> -
> -&sdmmc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
> - non-removable;
> - no-sd;
> - no-sdio;
> - st,neg-edge;
> - bus-width = <8>;
> - vmmc-supply = <&v3v3>;
> - mmc-ddr-3_3v;
> - status = "okay";
> -};
> -
> -&spi2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi2_pins_a>;
> - status = "okay";
> -};
> -
> -&uart4 {
> - /* On Low speed expansion header */
> - label = "LS-UART1";
> - pinctrl-names = "default";
> - pinctrl-0 = <&uart4_pins_b>;
> - status = "okay";
> -};
> -
> -&uart7 {
> - /* On Low speed expansion header */
> - label = "LS-UART0";
> - pinctrl-names = "default";
> - pinctrl-0 = <&uart7_pins_a>;
> - status = "okay";
> -};
> -
> -&usbh_ehci {
> - phys = <&usbphyc_port0>;
> - phy-names = "usb";
> - status = "okay";
> -};
> -
> -&usbotg_hs {
> - dr_mode = "peripheral";
> - phys = <&usbphyc_port1 0>;
> - phy-names = "usb2-phy";
> - status = "okay";
> -};
> -
> -&usbphyc {
> - status = "okay";
> -};
> -
> -&usbphyc_port0 {
> - phy-supply = <&vdd_usb>;
> -};
> -
> -&usbphyc_port1 {
> - phy-supply = <&vdd_usb>;
> -};
> +/* This is kept for backward compatibility and will be removed */
> +#include "stm32mp15xx-dhcor-avenger96.dts"
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
> new file mode 100644
> index 0000000000..484f1436b8
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96-u-boot.dtsi
> @@ -0,0 +1,80 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2020 Marek Vasut <marex at denx.de>
> + */
> +
> +#include "stm32mp15xx-dhcor-u-boot.dtsi"
> +
> +/ {
> + aliases {
> + mmc0 = &sdmmc1;
> + mmc1 = &sdmmc2;
> + usb0 = &usbotg_hs;
> + };
> +
> + config {
> + u-boot,boot-led = "led1";
> + u-boot,error-led = "led4";
> + };
> +};
> +
> +&sdmmc1 {
> + u-boot,dm-spl;
> +};
> +
> +&sdmmc1_b4_pins_a {
> + u-boot,dm-spl;
> + pins {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&sdmmc1_dir_pins_a {
> + u-boot,dm-spl;
> + pins1 {
> + u-boot,dm-spl;
> + };
> + pins2 {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&sdmmc2 {
> + u-boot,dm-spl;
> +};
> +
> +&sdmmc2_b4_pins_a {
> + u-boot,dm-spl;
> + pins1 {
> + u-boot,dm-spl;
> + };
> + pins2 {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&sdmmc2_d47_pins_a {
> + u-boot,dm-spl;
> + pins {
> + u-boot,dm-spl;
> + };
> +};
> +
> +&uart4 {
> + u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_b {
> + u-boot,dm-pre-reloc;
> + pins1 {
> + u-boot,dm-pre-reloc;
> + };
> + pins2 {
> + u-boot,dm-pre-reloc;
> + };
> +};
> +
> +&usbotg_hs {
> + u-boot,force-b-session-valid;
> + hnp-srp-disable;
> +};
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
> new file mode 100644
> index 0000000000..c912818ac9
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-avenger96.dts
> @@ -0,0 +1,196 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
> +/*
> + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
> + * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> + * Copyright (C) 2020 Marek Vasut <marex at denx.de>
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp15xx-dhcor.dtsi"
> +#include "stm32mp15xx-dhcor-avenger96-u-boot.dtsi"
> +
> +/ {
> + model = "Arrow Electronics STM32MP15xx Avenger96 board";
> + compatible = "arrow,stm32mp15xx-avenger96", "st,stm32mp15x";
> +
> + aliases {
> + eeprom0 = &eeprom0;
> + ethernet0 = ðernet0;
> + mmc0 = &sdmmc1;
> + serial0 = &uart4;
> + serial1 = &uart7;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + led {
> + compatible = "gpio-leds";
> + led1 {
> + label = "green:user1";
> + gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + default-state = "off";
> + };
> +
> + led2 {
> + label = "green:user2";
> + gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc0";
> + default-state = "off";
> + };
> +
> + led3 {
> + label = "green:user3";
> + gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "mmc1";
> + default-state = "off";
> + };
> +
> + led4 {
> + label = "green:user3";
> + gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "none";
> + default-state = "off";
> + panic-indicator;
> + };
> +
> + led5 {
> + label = "yellow:wifi";
> + gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "phy0tx";
> + default-state = "off";
> + };
> +
> + led6 {
> + label = "blue:bt";
> + gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "bluetooth-power";
> + default-state = "off";
> + };
> + };
> +};
> +
> +ðernet0 {
> + status = "okay";
> + pinctrl-0 = <ðernet0_rgmii_pins_b>;
> + pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rgmii";
> + max-speed = <1000>;
> + phy-handle = <&phy0>;
> + phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy at 7 {
> + reg = <7>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins_b>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +};
> +
> +&i2c4 {
> + eeprom0: eeprom at 53 {
> + compatible = "atmel,24c02";
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + broken-cd;
> + st,sig-dir;
> + st,neg-edge;
> + st,use-ckin;
> + bus-width = <4>;
> + vmmc-supply = <&vdd_sd>;
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <8>;
> + vmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> + status = "okay";
> +};
> +
> +&spi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2_pins_a>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + /* On Low speed expansion header */
> + label = "LS-UART1";
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins_b>;
> + status = "okay";
> +};
> +
> +&uart7 {
> + /* On Low speed expansion header */
> + label = "LS-UART0";
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart7_pins_a>;
> + status = "okay";
> +};
> +
> +&usbh_ehci {
> + phys = <&usbphyc_port0>;
> + phy-names = "usb";
> + status = "okay";
> +};
> +
> +&usbotg_hs {
> + dr_mode = "peripheral";
> + phys = <&usbphyc_port1 0>;
> + phy-names = "usb2-phy";
> + status = "okay";
> +};
> +
> +&usbphyc {
> + status = "okay";
> +};
> +
> +&usbphyc_port0 {
> + phy-supply = <&vdd_usb>;
> +};
> +
> +&usbphyc_port1 {
> + phy-supply = <&vdd_usb>;
> +};
> diff --git a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> similarity index 75%
> rename from arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
> rename to arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> index 8dcd8866e8..70b35e79e5 100644
> --- a/arch/arm/dts/stm32mp157a-avenger96-u-boot.dtsi
> +++ b/arch/arm/dts/stm32mp15xx-dhcor-u-boot.dtsi
> @@ -4,25 +4,13 @@
> *
> * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
> * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> + * Copyright (C) 2020 Marek Vasut <marex at denx.de>
> */
>
> #include <dt-bindings/clock/stm32mp1-clksrc.h>
> #include "stm32mp157-u-boot.dtsi"
> #include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
>
> -/ {
> - aliases {
> - mmc0 = &sdmmc1;
> - mmc1 = &sdmmc2;
> - usb0 = &usbotg_hs;
> - };
> -
> - config {
> - u-boot,boot-led = "led1";
> - u-boot,error-led = "led4";
> - };
> -};
> -
> &i2c4 {
> u-boot,dm-pre-reloc;
> };
> @@ -38,6 +26,10 @@
> u-boot,dm-pre-reloc;
> };
>
> +&qspi {
> + u-boot,dm-spl;
> +};
> +
> &rcc {
> st,clksrc = <
> CLK_MPU_PLL1P
> @@ -139,67 +131,6 @@
> };
> };
>
> -&sdmmc1 {
> - u-boot,dm-spl;
> -};
> -
> -&sdmmc1_b4_pins_a {
> - u-boot,dm-spl;
> - pins {
> - u-boot,dm-spl;
> - };
> -};
> -
> -&sdmmc1_dir_pins_a {
> - u-boot,dm-spl;
> - pins1 {
> - u-boot,dm-spl;
> - };
> - pins2 {
> - u-boot,dm-spl;
> - };
> -};
> -
> -&sdmmc2 {
> - u-boot,dm-spl;
> -};
> -
> -&sdmmc2_b4_pins_a {
> - u-boot,dm-spl;
> - pins1 {
> - u-boot,dm-spl;
> - };
> - pins2 {
> - u-boot,dm-spl;
> - };
> -};
> -
> -&sdmmc2_d47_pins_a {
> - u-boot,dm-spl;
> - pins {
> - u-boot,dm-spl;
> - };
> -};
> -
> -&uart4 {
> - u-boot,dm-pre-reloc;
> -};
> -
> -&uart4_pins_b {
> - u-boot,dm-pre-reloc;
> - pins1 {
> - u-boot,dm-pre-reloc;
> - };
> - pins2 {
> - u-boot,dm-pre-reloc;
> - };
> -};
> -
> -&usbotg_hs {
> - u-boot,force-b-session-valid;
> - hnp-srp-disable;
> -};
> -
> &v3v3 {
> regulator-always-on;
> };
> diff --git a/arch/arm/dts/stm32mp15xx-dhcor.dtsi b/arch/arm/dts/stm32mp15xx-dhcor.dtsi
> new file mode 100644
> index 0000000000..ff55505bfc
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp15xx-dhcor.dtsi
> @@ -0,0 +1,220 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
> +/*
> + * Copyright (C) Linaro Ltd 2019 - All Rights Reserved
> + * Author: Manivannan Sadhasivam <manivannan.sadhasivam at linaro.org>
> + * Copyright (C) 2020 Marek Vasut <marex at denx.de>
> + */
> +/dts-v1/;
> +
> +#include "stm32mp157c.dtsi"
> +#include "stm32mp157xac-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> + aliases {
> + spi0 = &qspi;
> + };
> +
> + memory at c0000000 {
> + device_type = "memory";
> + reg = <0xc0000000 0x40000000>;
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +
> + pmic: stpmic at 33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + status = "okay";
> +
> + st,main-control-register = <0x04>;
> + st,vin-control-register = <0xc0>;
> + st,usb-control-register = <0x30>;
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> +
> + ldo1-supply = <&v3v3>;
> + ldo2-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo5-supply = <&v3v3>;
> + ldo6-supply = <&v3v3>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + st,mask_reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + vdda: ldo1 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO1 0>;
> + interrupt-parent = <&pmic>;
> + };
> +
> + v2v8: ldo2 {
> + regulator-name = "v2v8";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + interrupts = <IT_CURLIM_LDO2 0>;
> + interrupt-parent = <&pmic>;
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <0>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + interrupts = <IT_CURLIM_LDO4 0>;
> + interrupt-parent = <&pmic>;
> + };
> +
> + vdd_sd: ldo5 {
> + regulator-name = "vdd_sd";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + interrupt-parent = <&pmic>;
> + regulator-boot-on;
> + };
> +
> + v1v8: ldo6 {
> + regulator-name = "v1v8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + interrupts = <IT_CURLIM_LDO6 0>;
> + interrupt-parent = <&pmic>;
> + regulator-enable-ramp-delay = <300000>;
> + };
> +
> + vref_ddr: vref_ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + interrupt-parent = <&pmic>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + interrupt-parent = <&pmic>;
> + regulator-active-discharge = <1>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + interrupt-parent = <&pmic>;
> + regulator-active-discharge = <1>;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + status = "okay";
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + status = "disabled";
> + };
> + };
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&pwr_regulators {
> + vdd-supply = <&vdd>;
> + vdd_3v3_usbfs-supply = <&vdd_usb>;
> +};
> +
> +&qspi {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
> + pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
> + reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + flash0: mx66l51235l at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <108000000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> diff --git a/doc/board/st/stm32mp1.rst b/doc/board/st/stm32mp1.rst
> index 1640bf910e..73195134f1 100644
> --- a/doc/board/st/stm32mp1.rst
> +++ b/doc/board/st/stm32mp1.rst
> @@ -43,11 +43,11 @@ And the necessary drivers
>
> Currently the following boards are supported:
>
> - + stm32mp157a-avenger96.dts
> + stm32mp157a-dk1.dts
> + stm32mp157c-dk2.dts
> + stm32mp157c-ed1.dts
> + stm32mp157c-ev1.dts
> + + stm32mp15xx-dhcor-avenger96.dts
>
> Boot Sequences
> --------------
> @@ -145,9 +145,9 @@ the supported device trees for STM32MP15x are:
>
> + stm32mp157c-dk2
>
> -+ avenger96: Avenger96 board from Arrow Electronics
> ++ avenger96: Avenger96 board from Arrow Electronics based on DH Elec. DHCOR SoM
>
> - + stm32mp157a-avenger96
> + + stm32mp15xx-dhcor-avenger96
>
> Build Procedure
> ---------------
> @@ -229,7 +229,7 @@ Build Procedure
>
> # export KBUILD_OUTPUT=stm32mp15_basic
> # make stm32mp15_basic_defconfig
> - # make DEVICE_TREE=stm32mp157a-avenger96 all
> + # make DEVICE_TREE=stm32mp15xx-dhcor-avenger96 all
>
> 6. Output files
>
Reviewed-by: Patrice Chotard <patrice.chotard at st.com>
Thanks
More information about the U-Boot
mailing list