[PATCH V2 3/7] drivers: ddr: imx8mp: Add inline ECC feature support
Peng Fan
peng.fan at nxp.com
Tue May 12 03:50:47 CEST 2020
From: Sherry Sun <sherry.sun at nxp.com>
the DRAM Controller in i.MX8MP will support a feature called "Inline ECC".
This is supported for all 3 supported DRAM technologies (LPDDR4, DDR4 and
DDR3L). When this feature is enabled by software, the DRAM Controller
reserves 12.5% of DRAM capacity for ECC information, and presents only
the non-ECC portion (lower 87.5% of the installed capacity of DRAM) to
the rest of the SoC.
The DRAM memory can be divided into 8 regions so that if a use case only
requires ECC protection on a subset of memory, then only that subset of
memory need support inline ECC. If this occurs, then there is no
performance penalty accessing the non-ECC-protected memory (no need to
access ECC for this portion of the memory map). This is all configured
with the DRAM Controller.
Signed-off-by: Sherry Sun <sherry.sun at nxp.com>
Signed-off-by: Peng Fan <peng.fan at nxp.com>
---
arch/arm/include/asm/arch-imx8m/ddr.h | 7 ++++
drivers/ddr/imx/imx8m/Kconfig | 7 ++++
drivers/ddr/imx/imx8m/ddr_init.c | 72 +++++++++++++++++++++++++++++++++++
3 files changed, 86 insertions(+)
diff --git a/arch/arm/include/asm/arch-imx8m/ddr.h b/arch/arm/include/asm/arch-imx8m/ddr.h
index 7a2a2d8edc..04c9c962cf 100644
--- a/arch/arm/include/asm/arch-imx8m/ddr.h
+++ b/arch/arm/include/asm/arch-imx8m/ddr.h
@@ -529,6 +529,8 @@ enum msg_response {
#define DDRC_SBRWDATA0(X) (DDRC_IPS_BASE_ADDR(X) + 0xf2c)
#define DDRC_SBRWDATA1(X) (DDRC_IPS_BASE_ADDR(X) + 0xf30)
#define DDRC_PDCH(X) (DDRC_IPS_BASE_ADDR(X) + 0xf34)
+#define DDRC_SBRSTART0(X) (DDRC_IPS_BASE_ADDR(X) + 0xf38)
+#define DDRC_SBRRANGE0(X) (DDRC_IPS_BASE_ADDR(X) + 0xf40)
#define DDRC_FREQ1_DERATEEN(X) (DDRC_IPS_BASE_ADDR(X) + 0x2020)
#define DDRC_FREQ1_DERATEINT(X) (DDRC_IPS_BASE_ADDR(X) + 0x2024)
@@ -708,6 +710,11 @@ int ddr_cfg_phy(struct dram_timing_info *timing_info);
void load_lpddr4_phy_pie(void);
void ddrphy_trained_csr_save(struct dram_cfg_param *param, unsigned int num);
void dram_config_save(struct dram_timing_info *info, unsigned long base);
+void board_dram_ecc_scrub(void);
+void ddrc_inline_ecc_scrub(unsigned int start_address,
+ unsigned int range_address);
+void ddrc_inline_ecc_scrub_end(unsigned int start_address,
+ unsigned int range_address);
/* utils function for ddr phy training */
int wait_ddrphy_training_complete(void);
diff --git a/drivers/ddr/imx/imx8m/Kconfig b/drivers/ddr/imx/imx8m/Kconfig
index 5bf61eb258..a5f5524fbe 100644
--- a/drivers/ddr/imx/imx8m/Kconfig
+++ b/drivers/ddr/imx/imx8m/Kconfig
@@ -29,4 +29,11 @@ config SAVED_DRAM_TIMING_BASE
info into memory for low power use. OCRAM_S is used for this
purpose on i.MX8MM.
default 0x180000
+
+config IMX8M_DRAM_INLINE_ECC
+ bool "imx8mp inline ECC"
+ depends on IMX8MP && IMX8M_LPDDR4
+ help
+ Select this config if you want to use inline ecc feature for
+ imx8mp-evk board.
endmenu
diff --git a/drivers/ddr/imx/imx8m/ddr_init.c b/drivers/ddr/imx/imx8m/ddr_init.c
index 06b4341b11..f573a778d9 100644
--- a/drivers/ddr/imx/imx8m/ddr_init.c
+++ b/drivers/ddr/imx/imx8m/ddr_init.c
@@ -20,6 +20,76 @@ void ddr_cfg_umctl2(struct dram_cfg_param *ddrc_cfg, int num)
}
}
+#ifdef CONFIG_IMX8M_DRAM_INLINE_ECC
+void ddrc_inline_ecc_scrub(unsigned int start_address,
+ unsigned int range_address)
+{
+ unsigned int tmp;
+
+ /* Step1: Enable quasi-dynamic programming */
+ reg32_write(DDRC_SWCTL(0), 0x00000000);
+ /* Step2: Set ECCCFG1.ecc_parity_region_lock to 1 */
+ reg32setbit(DDRC_ECCCFG1(0), 0x4);
+ /* Step3: Block the AXI ports from taking the transaction */
+ reg32_write(DDRC_PCTRL_0(0), 0x0);
+ /* Step4: Set scrub start address */
+ reg32_write(DDRC_SBRSTART0(0), start_address);
+ /* Step5: Set scrub range address */
+ reg32_write(DDRC_SBRRANGE0(0), range_address);
+ /* Step6: Set scrub_mode to write */
+ reg32_write(DDRC_SBRCTL(0), 0x00000014);
+ /* Step7: Set the desired pattern through SBRWDATA0 registers */
+ reg32_write(DDRC_SBRWDATA0(0), 0x55aa55aa);
+ /* Step8: Enable the SBR by programming SBRCTL.scrub_en=1 */
+ reg32setbit(DDRC_SBRCTL(0), 0x0);
+ /* Step9: Poll SBRSTAT.scrub_done=1 */
+ tmp = reg32_read(DDRC_SBRSTAT(0));
+ while (tmp != 0x00000002)
+ tmp = reg32_read(DDRC_SBRSTAT(0)) & 0x2;
+ /* Step10: Poll SBRSTAT.scrub_busy=0 */
+ tmp = reg32_read(DDRC_SBRSTAT(0));
+ while (tmp != 0x0)
+ tmp = reg32_read(DDRC_SBRSTAT(0)) & 0x1;
+ /* Step11: Disable SBR by programming SBRCTL.scrub_en=0 */
+ clrbits_le32(DDRC_SBRCTL(0), 0x1);
+ /* Step12: Prepare for normal scrub operation(Read) and set scrub_interval*/
+ reg32_write(DDRC_SBRCTL(0), 0x100);
+ /* Step13: Enable the SBR by programming SBRCTL.scrub_en=1 */
+ reg32_write(DDRC_SBRCTL(0), 0x101);
+ /* Step14: Enable AXI ports by programming */
+ reg32_write(DDRC_PCTRL_0(0), 0x1);
+ /* Step15: Disable quasi-dynamic programming */
+ reg32_write(DDRC_SWCTL(0), 0x00000001);
+}
+
+void ddrc_inline_ecc_scrub_end(unsigned int start_address,
+ unsigned int range_address)
+{
+ /* Step1: Enable quasi-dynamic programming */
+ reg32_write(DDRC_SWCTL(0), 0x00000000);
+ /* Step2: Block the AXI ports from taking the transaction */
+ reg32_write(DDRC_PCTRL_0(0), 0x0);
+ /* Step3: Set scrub start address */
+ reg32_write(DDRC_SBRSTART0(0), start_address);
+ /* Step4: Set scrub range address */
+ reg32_write(DDRC_SBRRANGE0(0), range_address);
+ /* Step5: Disable SBR by programming SBRCTL.scrub_en=0 */
+ clrbits_le32(DDRC_SBRCTL(0), 0x1);
+ /* Step6: Prepare for normal scrub operation(Read) and set scrub_interval */
+ reg32_write(DDRC_SBRCTL(0), 0x100);
+ /* Step7: Enable the SBR by programming SBRCTL.scrub_en=1 */
+ reg32_write(DDRC_SBRCTL(0), 0x101);
+ /* Step8: Enable AXI ports by programming */
+ reg32_write(DDRC_PCTRL_0(0), 0x1);
+ /* Step9: Disable quasi-dynamic programming */
+ reg32_write(DDRC_SWCTL(0), 0x00000001);
+}
+#endif
+
+void __weak board_dram_ecc_scrub(void)
+{
+}
+
int ddr_init(struct dram_timing_info *dram_timing)
{
unsigned int tmp, initial_drate, target_freq;
@@ -168,6 +238,8 @@ int ddr_init(struct dram_timing_info *dram_timing)
reg32_write(DDRC_PCTRL_0(0), 0x00000001);
debug("DDRINFO: ddrmix config done\n");
+ board_dram_ecc_scrub();
+
/* save the dram timing config into memory */
dram_config_save(dram_timing, CONFIG_SAVED_DRAM_TIMING_BASE);
--
2.16.4
More information about the U-Boot
mailing list