raspberrypi cm3 v2019.07 not working

[Matthias Brugger]

On 12/05/2020 13:36, Belisko Marek wrote:
> On Tue, May 12, 2020 at 1:16 PM Matthias Brugger <matthias.bgg at gmail.com> wrote:
>>
>>
>>
>> On 12/05/2020 13:00, Belisko Marek wrote:
>>> On Tue, May 12, 2020 at 12:51 PM Matthias Brugger <mbrugger at suse.com> wrote:
>>>>
>>>>
>>>>
>>>> On 12/05/2020 11:15, Belisko Marek wrote:
>>>>> On Fri, May 8, 2020 at 11:39 PM Belisko Marek <marek.belisko at gmail.com> wrote:
>>>>>>
>>>>>> Hi Matthias,
>>>>>>
>>>>>> On Fri, May 8, 2020 at 11:28 PM Matthias Brugger <mbrugger at suse.com> wrote:
>>>>>>>
>>>>>>> Hi Marek,
>>>>>>>
>>>>>>> On 08/05/2020 21:52, Belisko Marek wrote:
>>>>>>>> On Wed, May 6, 2020 at 11:02 PM Belisko Marek <marek.belisko at gmail.com> wrote:
>>>>>>>>>
>>>>>>>>> On Tue, May 5, 2020 at 10:18 PM Belisko Marek <marek.belisko at gmail.com> wrote:
>>>>>>>>>>
>>>>>>>>>> Hi,
>>>>>>>>>>
>>>>>>>>>> I'm trying to run 2019.07 u-boot on raspberrypi cm3 module but I got
>>>>>>>>>> no feedback on console. When used 2018.01 it boots fine. Probably I
>>>>>>>>>> need to do git bisect but maybe someone have some idea or experience
>>>>>>>>>> what can cause that. Thanks.
>>>>>>>>> I give a try 2020.01 and I got only this:
>>>>>>>>> U-Boot 2020.01 (May 06 2020 - 20:09:45 +0000)
>>>>>>>>>
>>>>>>>>> DRAM:  948 MiB
>>>>>>>>> RPI Compute Module 3 (0xa020a0)
>>>>>>>>>
>>>>>>>>> I'll try to debug it and let you know.
>>>>>>>> Debug messages shows this:
>>>>>>>> https://pastebin.com/2SwNzrb1
>>>>>>>>
>>>>>>>> I tried to debug but I have no clue what is going one there.
>>>>>>>>
>>>>>>>> Also u-boot 2019.07 is not working at all on cm3 due to this commit
>>>>>>>> (after bisect when reverted u-boot start working again):
>>>>>>>> 143256b353c4d2ad1cf5e5e63b38410188b35e49 - fdt: update bcm283x device
>>>>>>>> tree sources to Linux 5.1-rc6 state
>>>>>>>>
>>>>>>>> Any ideas hint how to resolve this issue? Thanks.
>>>>>>>>
>>>>>>>
>>>>>>> Can you try to cherry-pick the following two patches to your tree:
>>>>>>> 5051377a0b ("arm: dts: bcm283x: Rename U-Boot file")
>>>>>>> 89e47e8eb6 ("fdt: fix bcm283x dm-pre-reloc definitions")
>>>>>> But those are present in 2020.01 and this version at least print
>>>>>> something to console but stuck somewhere (pls see pastebin log with
>>>>>> debug enabled)
>>>>>> I prefer to run 2020.01 ;). Thanks.
>>>>> Any other stuff I can try to make it working in 2020.01? Could that be
>>>>> firmware issue somehow? Thanks.
>>>>
>>>> Sorry I didn't realized that your first try was with 2020.01.
>>>> I just confirmed that it acutually does not boot. As a shortcut, do you know
>>>> which is the last working version of U-Boot?
>>> v2019.07 with reverted  commit :
>>> 143256b353c4d2ad1cf5e5e63b38410188b35e49 - fdt: update bcm283x device
>>> tree sources to Linux 5.1-rc6 state
>>> work fine. Without revert it shows anything on console. So something
>>> between 2019.07..2020.01 mus fix it partially ;)
>>
>> I just tired v2020.04 and it works for me. Would you mind testing that on your end?
> OK I'll give a try and try to bisect between 2020.01 and 2020.04. I
> have dependency on 2020.01 as I integrate mender
> and then use this version.

I'm on that no need for you to do it.

Regards,
Matthias