[PATCH v10 17/18] configs: fu540: Add config options for U-Boot SPL

Fri May 15 19:35:06 CEST 2020

On Thu, May 14, 2020 at 5:24 PM Pragnesh Patel
<pragnesh.patel at sifive.com> wrote:
>
> With sifive_fu540_defconfig:
>
> User can use FSBL or u-boot-spl.bin anyone at a time.
>
> For FSBL,
> fsbl->fw_payload.bin (opensbi + U-Boot)
>
> For u-boot-spl.bin,
> u-boot-spl.bin->FIT image (opensbi + U-Boot proper + dtb)
>
> U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
> u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
> image u-boot.itb from SD card into RAM.
>
> U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
> number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
>
> Signed-off-by: Pragnesh Patel <pragnesh.patel at sifive.com>
> Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
> Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
> ---
>  configs/sifive_fu540_defconfig |   8 ++
>  doc/board/sifive/fu540.rst     | 134 +++++++++++++++++++++++++++++++++
>  2 files changed, 142 insertions(+)
>
> diff --git a/configs/sifive_fu540_defconfig b/configs/sifive_fu540_defconfig
> index f805aacc7a..8d412f8d6a 100644
> --- a/configs/sifive_fu540_defconfig
> +++ b/configs/sifive_fu540_defconfig
> @@ -1,6 +1,11 @@
>  CONFIG_RISCV=y
> +CONFIG_SPL_GPIO_SUPPORT=y
> +CONFIG_SYS_MALLOC_F_LEN=0x3000
>  CONFIG_ENV_SIZE=0x20000
> +CONFIG_SPL_MMC_SUPPORT=y
>  CONFIG_NR_DRAM_BANKS=1
> +CONFIG_SPL=y
> +CONFIG_SPL_SPI_SUPPORT=y
>  CONFIG_TARGET_SIFIVE_FU540=y
>  CONFIG_ARCH_RV64I=y
>  CONFIG_RISCV_SMODE=y
> @@ -9,7 +14,10 @@ CONFIG_FIT=y
>  CONFIG_MISC_INIT_R=y
>  CONFIG_DISPLAY_CPUINFO=y
>  CONFIG_DISPLAY_BOARDINFO=y
> +CONFIG_SPL_SEPARATE_BSS=y
> +CONFIG_SPL_YMODEM_SUPPORT=y
>  CONFIG_OF_BOARD_FIXUP=y
>  CONFIG_DEFAULT_DEVICE_TREE="hifive-unleashed-a00"
>  CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_SPL_CLK=y
>  CONFIG_DM_MTD=y
> diff --git a/doc/board/sifive/fu540.rst b/doc/board/sifive/fu540.rst
> index 610ba87074..89e8d66c56 100644
> --- a/doc/board/sifive/fu540.rst
> +++ b/doc/board/sifive/fu540.rst
> @@ -31,6 +31,9 @@ TODO:
>          stdout-path = "/soc/serial at 10010000:115200";
>     };
>
> +Booting from MMC using FSBL
> +---------------------------
> +
>  Building
>  --------
>
> @@ -421,3 +424,134 @@ as well.
>
>     Please press Enter to activate this console.
>     / #
> +
> +Booting from MMC using U-Boot SPL
> +---------------------------------
> +
> +Building
> +--------
> +
> +Before building U-Boot SPL, OpenSBI must be built first. OpenSBI can be
> +cloned and built for FU540 as below:
> +
> +.. code-block:: console
> +
> +       git clone https://github.com/riscv/opensbi.git
> +       cd opensbi
> +       make PLATFORM=generic FW_DYNAMIC=y
> +
> +Copy OpenSBI FW_DYNAMIC image
> +(build/platform/generic/firmware/fw_dynamic.bin) into U-Boot
> +root directory
> +
> +.. code-block:: console
> +
> +       cp build/platform/generic/firmware/fw_dynamic.bin <u-boot-dir>
> +
> +Now build the U-Boot SPL and U-Boot proper
> +
> +.. code-block:: console
> +
> +       cd <U-Boot-dir>
> +       make sifive_fu540_defconfig
> +       make
> +
> +This will generate spl/u-boot-spl.bin and FIT image (u-boot.itb)
> +
> +
> +Flashing
> +--------
> +
> +ZSBL loads the U-Boot SPL (u-boot-spl.bin) from a partition with GUID type
> +5B193300-FC78-40CD-8002-E86C45580B47
> +
> +U-Boot SPL expects a U-Boot FIT image (u-boot.itb) from a partition with GUID
> +type 2E54B353-1271-4842-806F-E436D6AF6985
> +
> +FIT image (u-boot.itb) is a combination of fw_dynamic.bin, u-boot-nodtb.bin and
> +device tree blob (hifive-unleashed-a00.dtb)
> +
> +Format the SD card (make sure the disk has GPT, otherwise use gdisk to switch)
> +
> +.. code-block:: none
> +
> +       # sudo sgdisk --clear \
> +       > --set-alignment=2 \
> +       > --new=1:34:2081 --change-name=1:loader1 --typecode=1:5B193300-FC78-40CD-8002-E86C45580B47 \
> +       > --new=2:2082:10273 --change-name=2:loader2 --typecode=2:2E54B353-1271-4842-806F-E436D6AF6985 \
> +       > --new=3:10274: --change-name=3:rootfs --typecode=3:0FC63DAF-8483-4772-8E79-3D69D8477DE4 \
> +       > /dev/sda
> +
> +Program the SD card
> +
> +.. code-block:: none
> +
> +       sudo dd if=spl/u-boot-spl.bin of=/dev/sda seek=34
> +       sudo dd if=u-boot.itb of=/dev/sda seek=2082
> +
> +Booting
> +-------
> +Once you plugin the sdcard and power up, you should see the U-Boot prompt.
> +
> +Sample boot log from HiFive Unleashed board
> +-------------------------------------------
> +
> +.. code-block:: none
> +
> +       U-Boot SPL 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> +       Trying to boot from MMC1
> +
> +
> +       U-Boot 2020.04-rc2-00109-g63efc7e07e-dirty (Apr 30 2020 - 13:52:36 +0530)
> +
> +       CPU:   rv64imafdc
> +       Model: SiFive HiFive Unleashed A00
> +       DRAM:  8 GiB
> +       MMC:   spi at 10050000:mmc at 0: 0
> +       In:    serial at 10010000
> +       Out:   serial at 10010000
> +       Err:   serial at 10010000
> +       Board serial number should not be 0 !!
> +       Net:
> +       Warning: ethernet at 10090000 (eth0) using random MAC address - 96:06:92:18:eb:04
> +       eth0: ethernet at 10090000
> +       Hit any key to stop autoboot:  0

Look like v10 seems to be a change, I can see memory region print?

U-Boot SPL 2020.07-rc1-00540-gd06cdf6989 (May 15 2020 - 23:00:17
+0530)
Trying to boot from MMC1

U-Boot 2020.07-rc1-00540-gd06cdf6989 (May 15 2020 - 23:00:17 +0530)

CPU:   rv64imafdc
Model: SiFive HiFive Unleashed A00
DRAM:  8 GiB
No reserved memory region found in source FDT
MMC:   spi at 10050000:mmc at 0: 0
In:    serial at 10010000
Out:   serial at 10010000
Err:   serial at 10010000
Net:   eth0: ethernet at 10090000
Hit any key to stop autoboot:  0

Jagan.