[PATCH 6/6 v3] configs: lx2160a: Add default config for lx2160a using StMM in OP-TEE

[Heinrich Schuchardt]

On 5/15/20 9:53 PM, Ilias Apalodimas wrote:
> Previous patches allow UEFI secure variables to be stored in an RPMB
> device using OPTEE. Add a config for the lx2160a hardware so the feature
> gets at least compiled.
>
> Signed-off-by: Ilias Apalodimas <ilias.apalodimas at linaro.org>
> ---
>  configs/lx2160ardb_tfa_stmm_defconfig | 78 +++++++++++++++++++++++++++
>  1 file changed, 78 insertions(+)
>  create mode 100644 configs/lx2160ardb_tfa_stmm_defconfig
>
> diff --git a/configs/lx2160ardb_tfa_stmm_defconfig b/configs/lx2160ardb_tfa_stmm_defconfig
> new file mode 100644
> index 000000000000..42d0d45ef0f1
> --- /dev/null
> +++ b/configs/lx2160ardb_tfa_stmm_defconfig
> @@ -0,0 +1,78 @@
> +CONFIG_ARM=y
> +CONFIG_TARGET_LX2160ARDB=y
> +CONFIG_TFABOOT=y
> +CONFIG_SYS_TEXT_BASE=0x82000000
> +CONFIG_SYS_MALLOC_F_LEN=0x6000
> +CONFIG_DM_GPIO=y
> +CONFIG_EMC2305=y
> +CONFIG_FSPI_AHB_EN_4BYTE=y
> +CONFIG_NR_DRAM_BANKS=3
> +CONFIG_ARMV8_SEC_FIRMWARE_SUPPORT=y
> +CONFIG_SEC_FIRMWARE_ARMV8_PSCI=y
> +CONFIG_AHCI=y
> +CONFIG_FIT_VERBOSE=y
> +CONFIG_OF_BOARD_SETUP=y
> +CONFIG_OF_STDOUT_VIA_ALIAS=y
> +CONFIG_BOOTDELAY=10
> +CONFIG_USE_BOOTARGS=y
> +CONFIG_BOOTARGS="console=ttyAMA0,115200 root=/dev/ram0 earlycon=pl011,mmio32,0x21c0000 ramdisk_size=0x2000000 default_hugepagesz=1024m hugepagesz=1024m hugepages=2 pci=pcie_bus_perf"
> +# CONFIG_USE_BOOTCOMMAND is not set
> +CONFIG_CMD_BOOTEFI_SELFTEST=y

This is nothing you would need on a production system.

> +CONFIG_CMD_GREPENV=y
> +CONFIG_CMD_NVEDIT_EFI=y
> +CONFIG_CMD_EEPROM=y
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +# CONFIG_CMD_MMC_RPMB is not set

You have enabled RPMB because the OP-TEE based standalone MM module
stores variables in the RPMB partition. Consider enabling this command.

Compared to lx2160ardb_tfa_defconfig you disabled the following:

> CONFIG_GIC_V3_ITS=y
> CONFIG_ENV_SIZE=0x2000
> CONFIG_ENV_OFFSET=0x500000
> CONFIG_ENV_SECT_SIZE=0x20000
> CONFIG_MISC_INIT_R=y
> CONFIG_CMD_DM=y
> CONFIG_ENV_IS_IN_MMC=y
> CONFIG_ENV_IS_IN_SPI_FLASH=y
> CONFIG_ENV_ADDR=0x20500000
> CONFIG_MTD=y
> CONFIG_DM_ETH=y
> CONFIG_DM_MDIO=y
> CONFIG_FSL_LS_MDIO=y

I would suggest to resync with the current lx2160ardb_tfa_defconfig.

CC: Priyanka Jain as maintainer of LX2160ARDB BOARD (which includes
lx2160ardb_tfa_defconfig).

Best regards

Heinrich

> +CONFIG_CMD_PCI=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_EFIDEBUG=y
> +CONFIG_MP=y
> +CONFIG_OF_CONTROL=y
> +CONFIG_OF_BOARD_FIXUP=y
> +CONFIG_DEFAULT_DEVICE_TREE="fsl-lx2160a-rdb"
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_TFTP_BLOCKSIZE=512
> +CONFIG_DM=y
> +CONFIG_SATA_CEVA=y
> +CONFIG_FSL_CAAM=y
> +CONFIG_DM_I2C=y
> +CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
> +CONFIG_I2C_DEFAULT_BUS_NUMBER=0
> +CONFIG_DM_MMC=y
> +CONFIG_SUPPORT_EMMC_RPMB=y
> +CONFIG_FSL_ESDHC=y
> +CONFIG_DM_SPI_FLASH=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> +CONFIG_PHYLIB=y
> +CONFIG_PHY_AQUANTIA=y
> +CONFIG_PHY_ATHEROS=y
> +CONFIG_PHY_CORTINA=y
> +CONFIG_E1000=y
> +CONFIG_PCI=y
> +CONFIG_DM_PCI=y
> +CONFIG_DM_PCI_COMPAT=y
> +CONFIG_PCIE_LAYERSCAPE=y
> +CONFIG_PCIE_LAYERSCAPE_GEN4=y
> +CONFIG_DM_RTC=y
> +CONFIG_RTC_PCF2127=y
> +CONFIG_DM_SCSI=y
> +CONFIG_DM_SERIAL=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_NXP_FSPI=y
> +CONFIG_TEE=y
> +CONFIG_OPTEE=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_XHCI_DWC3=y
> +# CONFIG_FAT_WRITE is not set
> +CONFIG_EFI_LOADER_BOUNCE_BUFFER=y
> +CONFIG_EFI_MM_COMM_TEE=y
> +CONFIG_OPTEE_TZDRAM_SIZE=0x00000000
>