[PATCH] mmc: davinci_mmc: Cleanup to use dt in U-boot and static platdata in SPL

Faiz Abbas faiz_abbas at ti.com
Fri May 22 04:02:28 CEST 2020


Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:

1. Move all platdata assignment from probe() to ofdata_to_platdata().
   This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
   ofdata_to_platdata() in the omapl138 board file. This data is used in
   the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig

This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')

Signed-off-by: Faiz Abbas <faiz_abbas at ti.com>
---

This patch fixes things being broken by Simon's series disabling
libfdt when using of-platdata:
https://patchwork.ozlabs.org/project/uboot/cover/20191107155318.103300-1-sjg@chromium.org/


 .../mach-davinci/include/mach/sdmmc_defs.h    |  7 +++
 board/davinci/da8xxevm/omapl138_lcdk.c        | 12 ++++
 configs/omapl138_lcdk_defconfig               |  4 --
 drivers/mmc/davinci_mmc.c                     | 63 ++++++++-----------
 4 files changed, 45 insertions(+), 41 deletions(-)

diff --git a/arch/arm/mach-davinci/include/mach/sdmmc_defs.h b/arch/arm/mach-davinci/include/mach/sdmmc_defs.h
index 46f6391aa2..f95a607e52 100644
--- a/arch/arm/mach-davinci/include/mach/sdmmc_defs.h
+++ b/arch/arm/mach-davinci/include/mach/sdmmc_defs.h
@@ -152,6 +152,13 @@ struct davinci_mmc {
 	struct mmc_config cfg;
 };
 
+#define DAVINCI_MAX_BLOCKS	(32)
+struct davinci_mmc_plat {
+	struct davinci_mmc_regs *reg_base;	/* Register base address */
+	struct mmc_config cfg;
+	struct mmc mmc;
+};
+
 int davinci_mmc_init(bd_t *bis, struct davinci_mmc *host);
 
 #endif /* _SDMMC_DEFS_H */
diff --git a/board/davinci/da8xxevm/omapl138_lcdk.c b/board/davinci/da8xxevm/omapl138_lcdk.c
index adb56c6c87..84603cb117 100644
--- a/board/davinci/da8xxevm/omapl138_lcdk.c
+++ b/board/davinci/da8xxevm/omapl138_lcdk.c
@@ -368,8 +368,20 @@ U_BOOT_DEVICE(omapl138_uart) = {
 	.platdata = &serial_pdata,
 };
 
+static const struct davinci_mmc_plat mmc_platdata = {
+	.reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
+	.cfg = {
+		.f_min = 200000,
+		.f_max = 25000000,
+		.voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+		.host_caps = MMC_MODE_4BIT,
+		.b_max = DAVINCI_MAX_BLOCKS,
+		.name = "da830-mmc",
+	},
+};
 U_BOOT_DEVICE(omapl138_mmc) = {
 	.name = "davinci_mmc",
+	.platdata = &mmc_platdata,
 };
 
 void spl_board_init(void)
diff --git a/configs/omapl138_lcdk_defconfig b/configs/omapl138_lcdk_defconfig
index 50cf09c7f1..b0a58de03d 100644
--- a/configs/omapl138_lcdk_defconfig
+++ b/configs/omapl138_lcdk_defconfig
@@ -40,16 +40,13 @@ CONFIG_CMD_MTDPARTS=y
 CONFIG_CMD_DIAG=y
 CONFIG_CMD_UBI=y
 CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
 CONFIG_DEFAULT_DEVICE_TREE="da850-lcdk"
-CONFIG_SPL_OF_PLATDATA=y
 CONFIG_ENV_IS_IN_NAND=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
 CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_DM=y
 CONFIG_SPL_DM=y
 CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_SPL_OF_TRANSLATE=y
 CONFIG_DA8XX_GPIO=y
 CONFIG_DM_I2C=y
 CONFIG_SYS_I2C_DAVINCI=y
@@ -82,4 +79,3 @@ CONFIG_USB_MUSB_HOST=y
 CONFIG_USB_MUSB_DA8XX=y
 CONFIG_USB_MUSB_PIO_ONLY=y
 CONFIG_USB_STORAGE=y
-# CONFIG_SPL_OF_LIBFDT is not set
diff --git a/drivers/mmc/davinci_mmc.c b/drivers/mmc/davinci_mmc.c
index 2408a687d2..4ef9f7cc8b 100644
--- a/drivers/mmc/davinci_mmc.c
+++ b/drivers/mmc/davinci_mmc.c
@@ -18,7 +18,6 @@
 #include <asm-generic/gpio.h>
 #include <linux/delay.h>
 
-#define DAVINCI_MAX_BLOCKS	(32)
 #define WATCHDOG_COUNT		(100000)
 
 #define get_val(addr)		REG(addr)
@@ -34,12 +33,6 @@ struct davinci_mmc_priv {
 	struct gpio_desc cd_gpio;       /* Card Detect GPIO */
 	struct gpio_desc wp_gpio;       /* Write Protect GPIO */
 };
-
-struct davinci_mmc_plat
-{
-	struct mmc_config cfg;
-	struct mmc mmc;
-};
 #endif
 
 /* Set davinci clock prescalar value based on the required clock in HZ */
@@ -487,43 +480,16 @@ static int davinci_mmc_probe(struct udevice *dev)
 	struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
 	struct davinci_mmc_plat *plat = dev_get_platdata(dev);
 	struct davinci_mmc_priv *priv = dev_get_priv(dev);
- 	struct mmc_config *cfg = &plat->cfg;
-#ifdef CONFIG_SPL_BUILD
-	int ret;
-#endif
-
-	cfg->f_min = 200000;
-	cfg->f_max = 25000000;
-	cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
-	cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
-	cfg->b_max = DAVINCI_MAX_BLOCKS;
-	cfg->name = "da830-mmc";
 
-	priv->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
+	priv->reg_base = plat->reg_base;
 	priv->input_clk = clk_get(DAVINCI_MMCSD_CLKID);
-
 #if CONFIG_IS_ENABLED(DM_GPIO)
 	/* These GPIOs are optional */
 	gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, GPIOD_IS_IN);
 	gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, GPIOD_IS_IN);
 #endif
-
 	upriv->mmc = &plat->mmc;
 
-#ifdef CONFIG_SPL_BUILD
-	/*
-	 * FIXME This is a temporary workaround to enable the driver model in
-	 * SPL on omapl138-lcdk. For some reason the bind() callback is not
-	 * being called in SPL for MMC which breaks the mmc boot - the hack
-	 * is to call mmc_bind() from probe(). We also don't have full DT
-	 * support in SPL, hence the hard-coded base register address.
-	 */
-	priv->reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE;
-	ret = mmc_bind(dev, &plat->mmc, &plat->cfg);
-	if (ret)
-		return ret;
-#endif
-
 	return davinci_dm_mmc_init(dev);
 }
 
@@ -534,21 +500,44 @@ static int davinci_mmc_bind(struct udevice *dev)
 	return mmc_bind(dev, &plat->mmc, &plat->cfg);
 }
 
+#if CONFIG_IS_ENABLED(OF_CONTROL)
+static int davinci_mmc_ofdata_to_platdata(struct udevice *dev)
+{
+	struct davinci_mmc_plat *plat = dev_get_platdata(dev);
+	struct mmc_config *cfg = &plat->cfg;
+
+	plat->reg_base = (struct davinci_mmc_regs *)dev_read_addr(dev);
+	cfg->f_min = 200000;
+	cfg->f_max = 25000000;
+	cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
+	cfg->host_caps = MMC_MODE_4BIT, /* DA850 supports only 4-bit SD/MMC */
+	cfg->b_max = DAVINCI_MAX_BLOCKS;
+	cfg->name = "da830-mmc";
+
+	return 0;
+}
+
 static const struct udevice_id davinci_mmc_ids[] = {
 	{ .compatible = "ti,da830-mmc" },
 	{},
 };
-
+#endif
 U_BOOT_DRIVER(davinci_mmc_drv) = {
 	.name = "davinci_mmc",
 	.id		= UCLASS_MMC,
+#if CONFIG_IS_ENABLED(OF_CONTROL)
 	.of_match	= davinci_mmc_ids,
+	.platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
+	.ofdata_to_platdata = davinci_mmc_ofdata_to_platdata,
+#endif
 #if CONFIG_BLK
 	.bind		= davinci_mmc_bind,
 #endif
 	.probe = davinci_mmc_probe,
 	.ops = &davinci_mmc_ops,
-	.platdata_auto_alloc_size = sizeof(struct davinci_mmc_plat),
 	.priv_auto_alloc_size = sizeof(struct davinci_mmc_priv),
+#if !CONFIG_IS_ENABLED(OF_CONTROL)
+	.flags	= DM_FLAG_PRE_RELOC,
+#endif
 };
 #endif
-- 
2.17.1



More information about the U-Boot mailing list