[PATCH v4 13/20] mtd: spi-nor-core: Prepare Read SR and FSR for Octal DTR mode

[Pratyush Yadav]

The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in Octal DTR mode.
Use that information to send the correct Read SR command.

Some controllers might have trouble reading just 1 byte in DTR mode. So,
when we are in DTR mode read 2 bytes and discard the second. This shows
no side effects with the two flashes I tested: Micron mt35xu512aba and
Cypress s28hs512t.

Update Read FSR to mimic Read SR because they share the same
characteristics.

Signed-off-by: Pratyush Yadav <p.yadav at ti.com>
---
 drivers/mtd/spi/spi-nor-core.c | 43 +++++++++++++++++++++++++++++-----
 1 file changed, 37 insertions(+), 6 deletions(-)

diff --git a/drivers/mtd/spi/spi-nor-core.c b/drivers/mtd/spi/spi-nor-core.c
index 2cb419c7ca..656dd09ea2 100644
--- a/drivers/mtd/spi/spi-nor-core.c
+++ b/drivers/mtd/spi/spi-nor-core.c
@@ -376,15 +376,30 @@ static ssize_t spi_nor_write_data(struct spi_nor *nor, loff_t to, size_t len,
 static int read_sr(struct spi_nor *nor)
 {
 	int ret;
-	u8 val;
+	u8 val[2];
+	u8 addr_nbytes = nor->rdsr_addr_nbytes;
+	u8 dummy = nor->rdsr_dummy;
+	struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDSR, 1),
+					  SPI_MEM_OP_ADDR(addr_nbytes, 0, 1),
+					  SPI_MEM_OP_DUMMY(dummy, 1),
+					  SPI_MEM_OP_DATA_IN(1, NULL, 1));
 
-	ret = nor->read_reg(nor, SPINOR_OP_RDSR, &val, 1);
+	spi_nor_setup_op(nor, &op, nor->reg_proto);
+
+	/*
+	 * We don't want to read only one byte in DTR mode. So, read 2 and then
+	 * discard the second byte.
+	 */
+	if (spi_nor_protocol_is_dtr(nor->reg_proto))
+		op.data.nbytes = 2;
+
+	ret = spi_nor_read_write_reg(nor, &op, val);
 	if (ret < 0) {
 		pr_debug("error %d reading SR\n", (int)ret);
 		return ret;
 	}
 
-	return val;
+	return *val;
 }
 
 /*
@@ -395,15 +410,31 @@ static int read_sr(struct spi_nor *nor)
 static int read_fsr(struct spi_nor *nor)
 {
 	int ret;
-	u8 val;
+	u8 val[2];
+	u8 addr_nbytes = nor->rdsr_addr_nbytes;
+	u8 dummy = nor->rdsr_dummy;
 
-	ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
+	struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_RDFSR, 1),
+					  SPI_MEM_OP_ADDR(addr_nbytes, 0, 1),
+					  SPI_MEM_OP_DUMMY(dummy, 1),
+					  SPI_MEM_OP_DATA_IN(1, NULL, 1));
+
+	spi_nor_setup_op(nor, &op, nor->reg_proto);
+
+	/*
+	 * We don't want to read only one byte in DTR mode. So, read 2 and then
+	 * discard the second byte.
+	 */
+	if (spi_nor_protocol_is_dtr(nor->reg_proto))
+		op.data.nbytes = 2;
+
+	ret = spi_nor_read_write_reg(nor, &op, val);
 	if (ret < 0) {
 		pr_debug("error %d reading FSR\n", ret);
 		return ret;
 	}
 
-	return val;
+	return *val;
 }
 
 /*
-- 
2.26.2