[PATCH 22/24] arm: Remove configs/kmcoge4_defconfig board

Jagan Teki jagan at amarulasolutions.com
Wed May 27 19:10:46 CEST 2020


This board has not been converted to CONFIG_DM_SPI by the deadline.

Remove it.

Patch-cc: Valentin Longchamp <valentin.longchamp at ch.abb.com>
Signed-off-by: Jagan Teki <jagan at amarulasolutions.com>
---
 board/keymile/Kconfig                 |   1 -
 board/keymile/kmp204x/Kconfig         |  20 --
 board/keymile/kmp204x/MAINTAINERS     |   6 -
 board/keymile/kmp204x/Makefile        |  10 -
 board/keymile/kmp204x/ddr.c           |  69 ----
 board/keymile/kmp204x/eth.c           |  71 -----
 board/keymile/kmp204x/kmp204x.c       | 265 ----------------
 board/keymile/kmp204x/kmp204x.h       |   8 -
 board/keymile/kmp204x/law.c           |  39 ---
 board/keymile/kmp204x/pbi.cfg         |  74 -----
 board/keymile/kmp204x/pci.c           | 125 --------
 board/keymile/kmp204x/rcw_kmp204x.cfg |  11 -
 board/keymile/kmp204x/tlb.c           | 109 -------
 configs/kmcoge4_defconfig             |  68 ----
 include/configs/kmp204x.h             | 435 --------------------------
 15 files changed, 1311 deletions(-)
 delete mode 100644 board/keymile/kmp204x/Kconfig
 delete mode 100644 board/keymile/kmp204x/MAINTAINERS
 delete mode 100644 board/keymile/kmp204x/Makefile
 delete mode 100644 board/keymile/kmp204x/ddr.c
 delete mode 100644 board/keymile/kmp204x/eth.c
 delete mode 100644 board/keymile/kmp204x/kmp204x.c
 delete mode 100644 board/keymile/kmp204x/kmp204x.h
 delete mode 100644 board/keymile/kmp204x/law.c
 delete mode 100644 board/keymile/kmp204x/pbi.cfg
 delete mode 100644 board/keymile/kmp204x/pci.c
 delete mode 100644 board/keymile/kmp204x/rcw_kmp204x.cfg
 delete mode 100644 board/keymile/kmp204x/tlb.c
 delete mode 100644 configs/kmcoge4_defconfig
 delete mode 100644 include/configs/kmp204x.h

diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig
index e20c017436..8be7a18a2a 100644
--- a/board/keymile/Kconfig
+++ b/board/keymile/Kconfig
@@ -120,7 +120,6 @@ config SYS_IVM_EEPROM_PAGE_LEN
 	  Page size of inventory in EEPROM.
 
 source "board/keymile/km83xx/Kconfig"
-source "board/keymile/kmp204x/Kconfig"
 source "board/keymile/km_arm/Kconfig"
 
 endmenu
diff --git a/board/keymile/kmp204x/Kconfig b/board/keymile/kmp204x/Kconfig
deleted file mode 100644
index f74d4295c7..0000000000
--- a/board/keymile/kmp204x/Kconfig
+++ /dev/null
@@ -1,20 +0,0 @@
-if TARGET_KMP204X
-
-config SYS_BOARD
-	default "kmp204x"
-
-config SYS_VENDOR
-	default "keymile"
-
-config SYS_CONFIG_NAME
-	default "kmp204x"
-
-config BOARD_SPECIFIC_OPTIONS # dummy
-	def_bool y
-	select ARCH_P2041
-	select FSL_DDR_INTERACTIVE
-	select PHYS_64BIT
-	imply CMD_CRAMFS
-	imply FS_CRAMFS
-
-endif
diff --git a/board/keymile/kmp204x/MAINTAINERS b/board/keymile/kmp204x/MAINTAINERS
deleted file mode 100644
index fb3aefdd37..0000000000
--- a/board/keymile/kmp204x/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-KMP204X BOARD
-M:	Valentin Longchamp <valentin.longchamp at ch.abb.com>
-S:	Maintained
-F:	board/keymile/kmp204x/
-F:	include/configs/kmp204x.h
-F:	configs/kmcoge4_defconfig
diff --git a/board/keymile/kmp204x/Makefile b/board/keymile/kmp204x/Makefile
deleted file mode 100644
index 5523ee99aa..0000000000
--- a/board/keymile/kmp204x/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2001-2007
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-
-obj-y	:= kmp204x.o ddr.o eth.o tlb.o pci.o law.o ../common/common.o\
-		../common/ivm.o ../common/qrio.o
diff --git a/board/keymile/kmp204x/ddr.c b/board/keymile/kmp204x/ddr.c
deleted file mode 100644
index d9c9ddf2ba..0000000000
--- a/board/keymile/kmp204x/ddr.c
+++ /dev/null
@@ -1,69 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2009-2011 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <hwconfig.h>
-#include <init.h>
-#include <log.h>
-#include <asm/mmu.h>
-#include <fsl_ddr_sdram.h>
-#include <fsl_ddr_dimm_params.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void fsl_ddr_board_options(memctl_options_t *popts,
-				dimm_params_t *pdimm,
-				unsigned int ctrl_num)
-{
-	if (ctrl_num) {
-		printf("Wrong parameter for controller number %d", ctrl_num);
-		return;
-	}
-
-	/* automatic calibration for nb of cycles between read and DQS pre */
-	popts->cpo_override = 0xFF;
-
-	/* 1/2 clk delay between wr command and data strobe */
-	popts->write_data_delay = 4;
-	/* clk lauched 1/2 applied cylcle after address command */
-	popts->clk_adjust = 4;
-	/* 1T timing: command/address held for only 1 cycle */
-	popts->twot_en = 0;
-
-	/* we have only one module, half str should be OK */
-	popts->half_strength_driver_enable = 1;
-
-	/* wrlvl values overridden as recommended by ddr init func */
-	popts->wrlvl_override = 1;
-	popts->wrlvl_sample = 0xf;
-	popts->wrlvl_start = 0x6;
-
-	/* Enable ZQ calibration */
-	popts->zq_en = 1;
-
-	/* DHC_EN =1, ODT = 75 Ohm */
-	popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR_ODT_75ohm;
-}
-
-int dram_init(void)
-{
-	phys_size_t dram_size = 0;
-
-	puts("Initializing with SPD\n");
-
-	dram_size = fsl_ddr_sdram();
-
-	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
-	dram_size *= 0x100000;
-
-	debug("    DDR: ");
-	gd->ram_size = dram_size;
-
-	return 0;
-}
diff --git a/board/keymile/kmp204x/eth.c b/board/keymile/kmp204x/eth.c
deleted file mode 100644
index 8635a5448b..0000000000
--- a/board/keymile/kmp204x/eth.c
+++ /dev/null
@@ -1,71 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- */
-
-#include <common.h>
-#include <net.h>
-#include <netdev.h>
-#include <fm_eth.h>
-#include <fsl_mdio.h>
-#include <phy.h>
-
-int board_eth_init(bd_t *bis)
-{
-	int ret = 0;
-#ifdef CONFIG_FMAN_ENET
-	struct fsl_pq_mdio_info dtsec_mdio_info;
-
-	printf("Initializing Fman\n");
-
-	dtsec_mdio_info.regs =
-		(struct tsec_mii_mng *)CONFIG_SYS_FM1_DTSEC1_MDIO_ADDR;
-	dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
-
-	/* Register the real 1G MDIO bus */
-	fsl_pq_mdio_init(bis, &dtsec_mdio_info);
-
-	/* DTESC1/2 don't have a PHY, they are temporarily disabled
-	 * so that u-boot doesn't try to unsuccessfuly enable them */
-	fm_disable_port(FM1_DTSEC1);
-	fm_disable_port(FM1_DTSEC2);
-
-	/*
-	 * Program RGMII DTSEC5 (FM1 MAC5) on the EC2 physical itf
-	 * This is the debug interface, the only one used in u-boot
-	 */
-	fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
-	fm_info_set_mdio(FM1_DTSEC5,
-			 miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME));
-
-	ret = cpu_eth_init(bis);
-
-	/* reenable DTSEC1/2 for later (kernel) */
-	fm_enable_port(FM1_DTSEC1);
-	fm_enable_port(FM1_DTSEC2);
-#endif
-
-	return ret;
-}
-
-#if defined(CONFIG_PHYLIB) && defined(CONFIG_PHY_MARVELL)
-
-#define mv88E1118_PAGE_REG	22
-
-int board_phy_config(struct phy_device *phydev)
-{
-	if (phydev->addr == CONFIG_SYS_FM1_DTSEC5_PHY_ADDR) {
-		/* driver config is good */
-		if (phydev->drv->config)
-			phydev->drv->config(phydev);
-
-		/* but we still need to fix the LEDs */
-		phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0003);
-		phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x0840);
-		phy_write(phydev, MDIO_DEVAD_NONE, mv88E1118_PAGE_REG, 0x0000);
-	}
-
-	return 0;
-}
-#endif
diff --git a/board/keymile/kmp204x/kmp204x.c b/board/keymile/kmp204x/kmp204x.c
deleted file mode 100644
index 21afbc7f39..0000000000
--- a/board/keymile/kmp204x/kmp204x.c
+++ /dev/null
@@ -1,265 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2011,2012 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <env.h>
-#include <fdt_support.h>
-#include <image.h>
-#include <init.h>
-#include <netdev.h>
-#include <linux/compiler.h>
-#include <asm/mmu.h>
-#include <asm/processor.h>
-#include <asm/cache.h>
-#include <asm/immap_85xx.h>
-#include <asm/fsl_law.h>
-#include <asm/fsl_serdes.h>
-#include <asm/fsl_portals.h>
-#include <asm/fsl_liodn.h>
-#include <fm_eth.h>
-
-#include "../common/common.h"
-#include "../common/qrio.h"
-#include "kmp204x.h"
-
-static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
-
-int checkboard(void)
-{
-	printf("Board: Keymile %s\n", CONFIG_SYS_CONFIG_NAME);
-
-	return 0;
-}
-
-#define ZL30158_RST	8
-#define BFTIC4_RST	0
-#define RSTRQSR1_WDT_RR	0x00200000
-#define RSTRQSR1_SW_RR	0x00100000
-
-int board_early_init_f(void)
-{
-	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	bool cpuwd_flag = false;
-
-	/* configure mode for uP reset request */
-	qrio_uprstreq(UPREQ_CORE_RST);
-
-	/* board only uses the DDR_MCK0, so disable the DDR_MCK1/2/3 */
-	setbits_be32(&gur->ddrclkdr, 0x001f000f);
-
-	/* set reset reason according CPU register */
-	if ((gur->rstrqsr1 & (RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR)) ==
-	    RSTRQSR1_WDT_RR)
-		cpuwd_flag = true;
-
-	qrio_cpuwd_flag(cpuwd_flag);
-	/* clear CPU bits by writing 1 */
-	setbits_be32(&gur->rstrqsr1, RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR);
-
-	/* set the BFTIC's prstcfg to reset at power-up and unit reset only */
-	qrio_prstcfg(BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
-	/* and enable WD on it */
-	qrio_wdmask(BFTIC4_RST, true);
-
-	/* set the ZL30138's prstcfg to reset at power-up only */
-	qrio_prstcfg(ZL30158_RST, PRSTCFG_POWUP_RST);
-	/* and take it out of reset as soon as possible (needed for Hooper) */
-	qrio_prst(ZL30158_RST, false, false);
-
-	return 0;
-}
-
-int board_early_init_r(void)
-{
-	int ret = 0;
-	/* Flush d-cache and invalidate i-cache of any FLASH data */
-	flush_dcache();
-	invalidate_icache();
-
-	set_liodns();
-	setup_qbman_portals();
-
-	ret = trigger_fpga_config();
-	if (ret)
-		printf("error triggering PCIe FPGA config\n");
-
-	/* enable the Unit LED (red) & Boot LED (on) */
-	qrio_set_leds();
-
-	/* enable Application Buffer */
-	qrio_enable_app_buffer();
-
-	return 0;
-}
-
-unsigned long get_board_sys_clk(unsigned long dummy)
-{
-	return 66666666;
-}
-
-#define ETH_FRONT_PHY_RST	15
-#define QSFP2_RST		11
-#define QSFP1_RST		10
-#define ZL30343_RST		9
-
-int misc_init_f(void)
-{
-	/* configure QRIO pis for i2c deblocking */
-	i2c_deblock_gpio_cfg();
-
-	/* configure the front phy's prstcfg and take it out of reset */
-	qrio_prstcfg(ETH_FRONT_PHY_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
-	qrio_prst(ETH_FRONT_PHY_RST, false, false);
-
-	/* set the ZL30343 prstcfg to reset at power-up only */
-	qrio_prstcfg(ZL30343_RST, PRSTCFG_POWUP_RST);
-	/* and enable the WD on it */
-	qrio_wdmask(ZL30343_RST, true);
-
-	/* set the QSFPs' prstcfg to reset at power-up and unit rst only */
-	qrio_prstcfg(QSFP1_RST, PRSTCFG_POWUP_UNIT_RST);
-	qrio_prstcfg(QSFP2_RST, PRSTCFG_POWUP_UNIT_RST);
-
-	/* and enable the WD on them */
-	qrio_wdmask(QSFP1_RST, true);
-	qrio_wdmask(QSFP2_RST, true);
-
-	return 0;
-}
-
-#define NUM_SRDS_BANKS	2
-
-int misc_init_r(void)
-{
-	serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
-	u32 expected[NUM_SRDS_BANKS] = {SRDS_PLLCR0_RFCK_SEL_100,
-		SRDS_PLLCR0_RFCK_SEL_125};
-	unsigned int i;
-
-	/* check SERDES reference clocks */
-	for (i = 0; i < NUM_SRDS_BANKS; i++) {
-		u32 actual = in_be32(&regs->bank[i].pllcr0);
-		actual &= SRDS_PLLCR0_RFCK_SEL_MASK;
-		if (actual != expected[i]) {
-			printf("Warning: SERDES bank %u expects reference \
-			       clock %sMHz, but actual is %sMHz\n", i + 1,
-			       serdes_clock_to_string(expected[i]),
-			       serdes_clock_to_string(actual));
-		}
-	}
-
-	ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
-			CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
-	return 0;
-}
-
-#if defined(CONFIG_HUSH_INIT_VAR)
-int hush_init_var(void)
-{
-	ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
-	return 0;
-}
-#endif
-
-#if defined(CONFIG_LAST_STAGE_INIT)
-
-int last_stage_init(void)
-{
-#if defined(CONFIG_KMCOGE4)
-	/* on KMCOGE4, the BFTIC4 is on the LBAPP2 */
-	struct bfticu_iomap *bftic4 =
-		(struct bfticu_iomap *)CONFIG_SYS_LBAPP2_BASE;
-	u8 dip_switch = in_8((u8 *)&(bftic4->mswitch)) & BFTICU_DIPSWITCH_MASK;
-
-	if (dip_switch != 0) {
-		/* start bootloader */
-		puts("DIP:   Enabled\n");
-		env_set("actual_bank", "0");
-	}
-#endif
-	set_km_env();
-
-	return 0;
-}
-#endif
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-void fdt_fixup_fman_mac_addresses(void *blob)
-{
-	int node, i, ret;
-	char *tmp, *end;
-	unsigned char mac_addr[6];
-
-	/* get the mac addr from env */
-	tmp = env_get("ethaddr");
-	if (!tmp) {
-		printf("ethaddr env variable not defined\n");
-		return;
-	}
-	for (i = 0; i < 6; i++) {
-		mac_addr[i] = tmp ? simple_strtoul(tmp, &end, 16) : 0;
-		if (tmp)
-			tmp = (*end) ? end+1 : end;
-	}
-
-	/* find the correct fdt ethernet path and correct it */
-	node = fdt_path_offset(blob, "/soc/fman/ethernet at e8000");
-	if (node < 0) {
-		printf("no /soc/fman/ethernet path offset\n");
-		return;
-	}
-	ret = fdt_setprop(blob, node, "local-mac-address", &mac_addr, 6);
-	if (ret) {
-		printf("error setting local-mac-address property\n");
-		return;
-	}
-}
-#endif
-
-int ft_board_setup(void *blob, bd_t *bd)
-{
-	phys_addr_t base;
-	phys_size_t size;
-
-	ft_cpu_setup(blob, bd);
-
-	base = env_get_bootm_low();
-	size = env_get_bootm_size();
-
-	fdt_fixup_memory(blob, (u64)base, (u64)size);
-
-#if defined(CONFIG_HAS_FSL_DR_USB) || defined(CONFIG_HAS_FSL_MPH_USB)
-	fsl_fdt_fixup_dr_usb(blob, bd);
-#endif
-
-#ifdef CONFIG_PCI
-	pci_of_setup(blob, bd);
-#endif
-
-	fdt_fixup_liodn(blob);
-#ifdef CONFIG_SYS_DPAA_FMAN
-	fdt_fixup_fman_ethernet(blob);
-	fdt_fixup_fman_mac_addresses(blob);
-#endif
-
-	return 0;
-}
-
-#if defined(CONFIG_POST)
-
-/* DIC26_SELFTEST GPIO used to start factory test sw */
-#define SELFTEST_PORT	QRIO_GPIO_A
-#define SELFTEST_PIN	31
-
-int post_hotkeys_pressed(void)
-{
-	qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN);
-	return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN);
-}
-#endif
diff --git a/board/keymile/kmp204x/kmp204x.h b/board/keymile/kmp204x/kmp204x.h
deleted file mode 100644
index 00e1a06662..0000000000
--- a/board/keymile/kmp204x/kmp204x.h
+++ /dev/null
@@ -1,8 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- */
-
-
-void pci_of_setup(void *blob, bd_t *bd);
diff --git a/board/keymile/kmp204x/law.c b/board/keymile/kmp204x/law.c
deleted file mode 100644
index 2d83dfea15..0000000000
--- a/board/keymile/kmp204x/law.c
+++ /dev/null
@@ -1,39 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/fsl_law.h>
-#include <asm/mmu.h>
-
-struct law_entry law_table[] = {
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
-	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
-	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
-	/* Limit DCSR to 32M to access NPC Trace Buffer */
-	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE_PHYS
-	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_32K, LAW_TRGT_IF_LBC),
-#endif
-	SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_LBC),
-#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
-	SET_LAW(CONFIG_SYS_LBAPP1_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-#endif
-#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
-	SET_LAW(CONFIG_SYS_LBAPP2_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-#endif
-};
-
-int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/keymile/kmp204x/pbi.cfg b/board/keymile/kmp204x/pbi.cfg
deleted file mode 100644
index 3fdfb47ab2..0000000000
--- a/board/keymile/kmp204x/pbi.cfg
+++ /dev/null
@@ -1,74 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright 2012 Freescale Semiconductor, Inc.
-# Refer docs/README.pblimage for more details about how-to configure
-# and create PBL boot image
-#
-
-#PBI commands
-#Configure ALTCBAR for DCSR -> DCSR at 89000000
-091380c0 000009C4
-09000010 00000000
-091380c0 000009C4
-09000014 00000000
-091380c0 000009C4
-09000018 81d00000
-#Workaround for A-004849
-091380c0 000009C4
-890B0050 00000002
-091380c0 000009C4
-890B0054 00000002
-091380c0 000009C4
-890B0058 00000002
-091380c0 000009C4
-890B005C 00000002
-091380c0 000009C4
-890B0090 00000002
-091380c0 000009C4
-890B0094 00000002
-091380c0 000009C4
-890B0098 00000002
-091380c0 000009C4
-890B009C 00000002
-091380c0 000009C4
-890B0108 00000012
-091380c0 000009C4
-#Workaround for A-006559 needed for rev 2.0 of P2041 silicon
-89021008 0000f000
-091380c0 000009C4
-89021028 0000f000
-091380c0 000009C4
-89021048 0000f000
-091380c0 000009C4
-89021068 0000f000
-091380c0 000009C4
-#Flush PBL data
-09138000 00000000
-#Disable ALTCBAR
-09000018 00000000
-091380c0 000009C4
-#Initialize CPC1 as 1MB SRAM
-09010000 00200400
-09138000 00000000
-091380c0 00000100
-09010100 00000000
-09010104 fff0000b
-09010f00 08000000
-09010000 80000000
-#Configure LAW for CPC1
-09000d00 00000000
-09000d04 fff00000
-09000d08 81000013
-09000010 00000000
-09000014 ff000000
-09000018 81000000
-#Initialize eSPI controller, default configuration is slow for eSPI to
-#load data, this configuration comes from u-boot eSPI driver.
-09110000 80000403
-09110020 27170008
-09110024 00100008
-09110028 00100008
-0911002c 00100008
-#Flush PBL data
-09138000 00000000
-091380c0 00000000
diff --git a/board/keymile/kmp204x/pci.c b/board/keymile/kmp204x/pci.c
deleted file mode 100644
index 87bf16886a..0000000000
--- a/board/keymile/kmp204x/pci.c
+++ /dev/null
@@ -1,125 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2007-2011 Freescale Semiconductor, Inc.
- */
-
-#include <common.h>
-#include <command.h>
-#include <init.h>
-#include <pci.h>
-#include <asm/fsl_pci.h>
-#include <linux/delay.h>
-#include <linux/libfdt.h>
-#include <fdt_support.h>
-#include <asm/fsl_serdes.h>
-#include <linux/errno.h>
-
-#include "../common/qrio.h"
-#include "kmp204x.h"
-
-#define PROM_SEL_L	11
-/* control the PROM_SEL_L signal*/
-static void toggle_fpga_eeprom_bus(bool cpu_own)
-{
-	qrio_gpio_direction_output(QRIO_GPIO_A, PROM_SEL_L, !cpu_own);
-}
-
-#define CONF_SEL_L	10
-#define FPGA_PROG_L	19
-#define FPGA_DONE	18
-#define FPGA_INIT_L	17
-
-int trigger_fpga_config(void)
-{
-	int ret = 0, init_l;
-	/* approx 10ms */
-	u32 timeout = 10000;
-
-	/* make sure the FPGA_can access the EEPROM */
-	toggle_fpga_eeprom_bus(false);
-
-	/* assert CONF_SEL_L to be able to drive FPGA_PROG_L */
-	qrio_gpio_direction_output(QRIO_GPIO_A, CONF_SEL_L, 0);
-
-	/* trigger the config start */
-	qrio_gpio_direction_output(QRIO_GPIO_A, FPGA_PROG_L, 0);
-
-	/* small delay for INIT_L line */
-	udelay(10);
-
-	/* wait for FPGA_INIT to be asserted */
-	do {
-		init_l = qrio_get_gpio(QRIO_GPIO_A, FPGA_INIT_L);
-		if (timeout-- == 0) {
-			printf("FPGA_INIT timeout\n");
-			ret = -EFAULT;
-			break;
-		}
-		udelay(10);
-	} while (init_l);
-
-	/* deassert FPGA_PROG, config should start */
-	qrio_set_gpio(QRIO_GPIO_A, FPGA_PROG_L, 1);
-
-	return ret;
-}
-
-/* poll the FPGA_DONE signal and give the EEPROM back to the QorIQ */
-static int wait_for_fpga_config(void)
-{
-	int ret = 0, done;
-	/* approx 5 s */
-	u32 timeout = 500000;
-
-	printf("PCIe FPGA config:");
-	do {
-		done = qrio_get_gpio(QRIO_GPIO_A, FPGA_DONE);
-		if (timeout-- == 0) {
-			printf(" FPGA_DONE timeout\n");
-			ret = -EFAULT;
-			goto err_out;
-		}
-		udelay(10);
-	} while (!done);
-
-	printf(" done\n");
-
-err_out:
-	/* deactive CONF_SEL and give the CPU conf EEPROM access */
-	qrio_set_gpio(QRIO_GPIO_A, CONF_SEL_L, 1);
-	toggle_fpga_eeprom_bus(true);
-
-	return ret;
-}
-
-#define PCIE_SW_RST	14
-#define PEXHC_RST	13
-#define HOOPER_RST	12
-
-void pci_init_board(void)
-{
-	qrio_prstcfg(PCIE_SW_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
-	qrio_prstcfg(PEXHC_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
-	qrio_prstcfg(HOOPER_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
-
-	/* wait for the PCIe FPGA to be configured
-	 * it has been triggered earlier in board_early_init_r */
-	if (wait_for_fpga_config())
-		printf("error finishing PCIe FPGA config\n");
-
-	qrio_prst(PCIE_SW_RST, false, false);
-	qrio_prst(PEXHC_RST, false, false);
-	qrio_prst(HOOPER_RST, false, false);
-	/* Hooper is not direcly PCIe capable */
-	mdelay(50);
-
-	fsl_pcie_init_board(0);
-}
-
-void pci_of_setup(void *blob, bd_t *bd)
-{
-	FT_FSL_PCI_SETUP;
-}
diff --git a/board/keymile/kmp204x/rcw_kmp204x.cfg b/board/keymile/kmp204x/rcw_kmp204x.cfg
deleted file mode 100644
index 236d5138bc..0000000000
--- a/board/keymile/kmp204x/rcw_kmp204x.cfg
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# Default RCW for kmp204x boards
-#
-
-#PBL preamble and RCW header
-aa55aa55 010e0100
-#64 bytes RCW data
-14600000 00000000 28200000 00000000
-148E70CF CFC02000 58000000 41000000
-00000000 00000000 00000000 F0428816
-00000000 00000000 00000000 00000000
diff --git a/board/keymile/kmp204x/tlb.c b/board/keymile/kmp204x/tlb.c
deleted file mode 100644
index a268bd8e95..0000000000
--- a/board/keymile/kmp204x/tlb.c
+++ /dev/null
@@ -1,109 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- *
- * Copyright 2008-2011 Freescale Semiconductor, Inc.
- *
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-#include <common.h>
-#include <asm/mmu.h>
-
-struct fsl_e_tlb_entry tlb_table[] = {
-	/* TLB 0 - for temp stack in cache */
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
-		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
-		      MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
-		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
-		      MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
-		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
-		      MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
-		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
-		      MAS3_SW|MAS3_SR, 0,
-		      0, 0, BOOKE_PAGESZ_4K, 0),
-	/* TLB 1 */
-	/* *I*G - L3SRAM. When L3 is used as 1M SRAM, the address of the
-	 * SRAM is at 0xfff00000, it covered the 0xfffff000.
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
-		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 0, BOOKE_PAGESZ_1M, 1),
-
-	/* *I*G* - CCSRBAR */
-	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 1, BOOKE_PAGESZ_16M, 1),
-	/* QRIO */
-	SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 2, BOOKE_PAGESZ_64K, 1),
-	/* *I*G* - PCI1 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 3, BOOKE_PAGESZ_512M, 1),
-	/* *I*G* - PCI3 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_VIRT, CONFIG_SYS_PCIE3_MEM_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 4, BOOKE_PAGESZ_512M, 1),
-	/* *I*G* - PCI1&3 I/O */
-	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 6, BOOKE_PAGESZ_128K, 1),
-#ifdef CONFIG_SYS_LBAPP1_BASE_PHYS
-	/* LBAPP1 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP1_BASE, CONFIG_SYS_LBAPP1_BASE_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 7, BOOKE_PAGESZ_256M, 1),
-#endif
-#ifdef CONFIG_SYS_LBAPP2_BASE_PHYS
-	/* LBAPP2 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_LBAPP2_BASE, CONFIG_SYS_LBAPP2_BASE_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 8, BOOKE_PAGESZ_256M, 1),
-#endif
-	/* Bman/Qman */
-#ifdef CONFIG_SYS_BMAN_MEM_PHYS
-	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
-		      MAS3_SW|MAS3_SR, 0,
-		      0, 9, BOOKE_PAGESZ_1M, 1),
-	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
-		      CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 10, BOOKE_PAGESZ_1M, 1),
-#endif
-#ifdef CONFIG_SYS_QMAN_MEM_PHYS
-	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
-		      MAS3_SW|MAS3_SR, 0,
-		      0, 11, BOOKE_PAGESZ_1M, 1),
-	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
-		      CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 12, BOOKE_PAGESZ_1M, 1),
-#endif
-#ifdef CONFIG_SYS_DCSRBAR_PHYS
-	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 13, BOOKE_PAGESZ_4M, 1),
-#endif
-#ifdef CONFIG_SYS_NAND_BASE
-	/*
-	 * *I*G - NAND
-	 * entry 14 and 15 has been used hard coded, they will be disabled
-	 * in cpu_init_f, so we use entry 16 for nand.
-	 */
-	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
-		      MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
-		      0, 16, BOOKE_PAGESZ_32K, 1),
-#endif
-};
-
-int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/configs/kmcoge4_defconfig b/configs/kmcoge4_defconfig
deleted file mode 100644
index a0d2c1a726..0000000000
--- a/configs/kmcoge4_defconfig
+++ /dev/null
@@ -1,68 +0,0 @@
-CONFIG_PPC=y
-CONFIG_SYS_TEXT_BASE=0xfff40000
-CONFIG_ENV_SIZE=0x4000
-CONFIG_ENV_OFFSET=0x100000
-CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_BOOTCOUNT_BOOTLIMIT=3
-CONFIG_SYS_BOOTCOUNT_ADDR=0xFB000020
-CONFIG_ENV_OFFSET_REDUND=0x110000
-CONFIG_MPC85xx=y
-CONFIG_TARGET_KMP204X=y
-# CONFIG_SYS_MALLOC_F is not set
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_OF_STDOUT_VIA_ALIAS=y
-CONFIG_SYS_EXTRA_OPTIONS="KMCOGE4"
-CONFIG_VERSION_VARIABLE=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_BOARD_EARLY_INIT_R=y
-CONFIG_LAST_STAGE_INIT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_AUTOBOOT_KEYED=y
-CONFIG_AUTOBOOT_PROMPT="Hit <SPACE> key to stop autoboot in %2ds\n"
-CONFIG_AUTOBOOT_STOP_STR=" "
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_GREPENV=y
-CONFIG_CMD_EEPROM=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_I2C=y
-CONFIG_CMD_SF=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_MP=y
-# CONFIG_CMD_HASH is not set
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=fsl_elbc_nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=fsl_elbc_nand:-(ubi0);"
-# CONFIG_CMD_IRQ is not set
-CONFIG_CMD_UBI=y
-# CONFIG_CMD_UBIFS is not set
-CONFIG_DOS_PARTITION=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_DM=y
-CONFIG_BOOTCOUNT_LIMIT=y
-# CONFIG_MMC is not set
-CONFIG_MTD=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_SPI_FLASH=y
-CONFIG_SF_DEFAULT_MODE=0
-CONFIG_SF_DEFAULT_SPEED=20000000
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_PHYLIB=y
-CONFIG_PHYLIB_10G=y
-CONFIG_PHY_MARVELL=y
-CONFIG_PHY_GIGE=y
-CONFIG_E1000=y
-CONFIG_FMAN_ENET=y
-CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
-CONFIG_SYS_NS16550=y
-CONFIG_SPI=y
-CONFIG_FSL_ESPI=y
-CONFIG_BCH=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/kmp204x.h b/include/configs/kmp204x.h
deleted file mode 100644
index e43b2f7513..0000000000
--- a/include/configs/kmp204x.h
+++ /dev/null
@@ -1,435 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2013 Keymile AG
- * Valentin Longchamp <valentin.longchamp at keymile.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#if defined(CONFIG_KMCOGE4)
-#define CONFIG_HOSTNAME		"kmcoge4"
-
-#else
-#error ("Board not supported")
-#endif
-
-#define CONFIG_KMP204X
-
-/* an additionnal option is required for UBI as subpage access is
- * supported in u-boot
- */
-#define CONFIG_KM_UBI_PART_BOOT_OPTS		",2048"
-
-#define CONFIG_NAND_ECC_BCH
-
-/* common KM defines */
-#include "km/keymile-common.h"
-
-#define CONFIG_SYS_RAMBOOT
-#define CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
-#define CONFIG_SYS_FSL_PBL_PBI board/keymile/kmp204x/pbi.cfg
-#define CONFIG_SYS_FSL_PBL_RCW board/keymile/kmp204x/rcw_kmp204x.cfg
-
-/* High Level Configuration Options */
-#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
-#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
-
-#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC		CONFIG_SYS_NUM_DDR_CTLRS
-#define CONFIG_PCIE1			/* PCIE controller 1 */
-#define CONFIG_PCIE3			/* PCIE controller 3 */
-#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
-
-#define CONFIG_SYS_DPAA_RMAN		/* RMan */
-
-/* Environment in SPI Flash */
-#define CONFIG_ENV_TOTAL_SIZE		0x020000
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0)
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BACKSIDE_L2_CACHE
-#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
-#define CONFIG_BTB			/* toggle branch predition */
-
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#define CONFIG_ADDR_MAP
-#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
-
-#define CONFIG_POST CONFIG_SYS_POST_MEM_REGIONS	/* POST memory regions test */
-
-/*
- *  Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR		CONFIG_RAMBOOT_TEXT_BASE
-#define CONFIG_SYS_INIT_L3_ADDR_PHYS	(0xf00000000ull | \
-		CONFIG_RAMBOOT_TEXT_BASE)
-#define CONFIG_SYS_L3_SIZE		(1024 << 10)
-#define CONFIG_SYS_INIT_L3_END (CONFIG_SYS_INIT_L3_ADDR + CONFIG_SYS_L3_SIZE)
-
-#define CONFIG_SYS_DCSRBAR		0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-#define CONFIG_DDR_SPD
-
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define SPD_EEPROM_ADDRESS	0x54
-#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
-
-#define CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
-
-/******************************************************************************
- * (PRAM usage)
- * ... -------------------------------------------------------
- * ... |ROOTFSSIZE | PNVRAM |PHRAM |RESERVED_PRAM | END_OF_RAM
- * ... |<------------------- pram -------------------------->|
- * ... -------------------------------------------------------
- * @END_OF_RAM:
- * @CONFIG_KM_RESERVED_PRAM: reserved pram for special purpose
- * @CONFIG_KM_PHRAM: address for /var
- * @CONFIG_KM_PNVRAM: address for PNVRAM (for the application)
- * @CONFIG_KM_ROOTFSSIZE: address for rootfilesystem in RAM
- */
-
-/* size of rootfs in RAM */
-#define CONFIG_KM_ROOTFSSIZE	0x0
-/* pseudo-non volatile RAM [hex] */
-#define CONFIG_KM_PNVRAM	0x80000
-/* physical RAM MTD size [hex] */
-#define CONFIG_KM_PHRAM		0x100000
-/* reserved pram area at the end of memory [hex]
- * u-boot reserves some memory for the MP boot page
- */
-#define CONFIG_KM_RESERVED_PRAM	0x1000
-/* set the default PRAM value to at least PNVRAM + PHRAM when pram env variable
- * is not valid yet, which is the case for when u-boot copies itself to RAM
- */
-#define CONFIG_PRAM		((CONFIG_KM_PNVRAM + CONFIG_KM_PHRAM) >> 10)
-
-#define CONFIG_KM_CRAMFS_ADDR	0x2000000
-#define CONFIG_KM_KERNEL_ADDR	0x1000000	/* max kernel size 15.5Mbytes */
-#define CONFIG_KM_FDT_ADDR	0x1F80000	/* max dtb    size  0.5Mbytes */
-
-/*
- * Local Bus Definitions
- */
-
-/* Set the local bus clock 1/8 of plat clk, 2 clk delay LALE */
-#define CONFIG_SYS_LBC_LCRR		(LCRR_CLKDIV_8 | LCRR_EADC_2)
-
-/* Nand Flash */
-#define CONFIG_NAND_FSL_ELBC
-#define CONFIG_SYS_NAND_BASE		0xffa00000
-#define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
-
-#define CONFIG_SYS_NAND_BASE_LIST     {CONFIG_SYS_NAND_BASE}
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
-
-/* NAND flash config */
-#define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-			       | BR_PS_8	       /* Port Size = 8 bit */ \
-			       | BR_MS_FCM	       /* MSEL = FCM */ \
-			       | BR_V)		       /* valid */
-
-#define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB	      /* length 256K */ \
-			       | OR_FCM_BCTLD	/* LBCTL not ass */	\
-			       | OR_FCM_SCY_1	/* 1 clk wait cycle */	\
-			       | OR_FCM_RST	/* 1 clk read setup */	\
-			       | OR_FCM_PGS	/* Large page size */	\
-			       | OR_FCM_CST)	/* 0.25 command setup */
-
-#define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
-#define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-
-/* QRIO FPGA */
-#define CONFIG_SYS_QRIO_BASE		0xfb000000
-#define CONFIG_SYS_QRIO_BASE_PHYS	0xffb000000ull
-
-#define CONFIG_SYS_QRIO_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_QRIO_BASE_PHYS) \
-				| BR_PS_8	/* Port Size 8 bits */ \
-				| BR_DECC_OFF	/* no error corr */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-
-#define CONFIG_SYS_QRIO_OR_PRELIM  (OR_AM_64KB	/* length 64K */ \
-				| OR_GPCM_BCTLD /* no LCTL assert */ \
-				| OR_GPCM_ACS_DIV4 /* LCS 1/4 clk after */ \
-				| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
-				| OR_GPCM_TRLX /* relaxed tmgs */ \
-				| OR_GPCM_EAD) /* extra bus clk cycles */
-
-#define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_QRIO_BR_PRELIM /* QRIO Base Address */
-#define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_QRIO_OR_PRELIM /* QRIO Options */
-
-#define CONFIG_MISC_INIT_F
-
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
-	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
-	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-					GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0) / 2)
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x11C500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x11C600)
-#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR + 0x11D500)
-#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR + 0x11D600)
-
-#define CONFIG_KM_CONSOLE_TTY	"ttyS0"
-
-/* I2C */
-/* QRIO GPIOs used for deblocking */
-#define KM_I2C_DEBLOCK_PORT     QRIO_GPIO_A
-#define KM_I2C_DEBLOCK_SCL      20
-#define KM_I2C_DEBLOCK_SDA      21
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_SYS_I2C_SPEED		100000 /* deblocking */
-#define CONFIG_SYS_NUM_I2C_BUSES	3
-#define CONFIG_SYS_I2C_MAX_HOPS		1
-#define CONFIG_SYS_I2C_FSL		/* Use FSL I2C driver */
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_I2C_CMD_TREE
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
-#define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 1 } } }, \
-					{0, {{I2C_MUX_PCA9547, 0x70, 2 } } }, \
-				}
-#ifndef __ASSEMBLY__
-void set_sda(int state);
-void set_scl(int state);
-int get_sda(void);
-int get_scl(void);
-#endif
-
-#define CONFIG_KM_IVM_BUS		1	/* I2C1 (Mux-Port 1)*/
-
-/*
- * eSPI - Enhanced SPI
- */
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8010000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8010000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-
-/* Qman/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS	10
-#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
-#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
-#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
-#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
-					CONFIG_SYS_BMAN_CENA_SIZE)
-#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08
-#define CONFIG_SYS_QMAN_NUM_PORTALS	10
-#define CONFIG_SYS_QMAN_MEM_BASE	0xf4200000
-#define CONFIG_SYS_QMAN_MEM_PHYS	0xff4200000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
-#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
-#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
-#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
-#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
-					CONFIG_SYS_QMAN_CENA_SIZE)
-#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
-#define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-/* Default address of microcode for the Linux Fman driver
- * env is stored at 0x100000, sector size is 0x10000, x2 (redundant)
- * ucode is stored after env, so we got 0x120000.
- */
-#define CONFIG_SYS_FMAN_FW_ADDR	0x120000
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-/* RGMII (FM1 at DTESC5) is used as debug itf, it's the only one configured */
-#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR	0x11
-#define CONFIG_SYS_TBIPA_VALUE	8
-#define CONFIG_ETHPRIME		"FM1 at DTSEC5"
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO		/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * Hardware Watchdog
- */
-#define CONFIG_WATCHDOG			/* enable CPU watchdog */
-#define CONFIG_WATCHDOG_PRESC 34	/* wdog prescaler 2^(64-34) (~10min) */
-#define CONFIG_WATCHDOG_RC WRC_CHIP	/* reset chip on watchdog event */
-
-/*
- * additionnal command line configuration.
- */
-
-/* we don't need flash support */
-#undef CONFIG_JFFS2_CMDLINE
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory for Linux */
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-#define __USB_PHY_TYPE	utmi
-#define CONFIG_USB_EHCI_FSL
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-/* architecture specific default bootargs */
-#define CONFIG_KM_DEF_BOOT_ARGS_CPU		""
-
-/* FIXME: FDT_ADDR is unspecified */
-#define CONFIG_KM_DEF_ENV_CPU						\
-	"boot=bootm ${load_addr_r} - ${fdt_addr_r}\0"			\
-	"cramfsloadfdt="						\
-		"cramfsload ${fdt_addr_r} "				\
-		"fdt_0x${IVM_BoardId}_0x${IVM_HWKey}.dtb\0"		\
-	"fdt_addr_r=" __stringify(CONFIG_KM_FDT_ADDR) "\0"		\
-	"u-boot=" CONFIG_HOSTNAME "/u-boot.pbl\0"		\
-	"update="							\
-		"sf probe 0;sf erase 0 +${filesize};"			\
-		"sf write ${load_addr_r} 0 ${filesize};\0"		\
-	"set_fdthigh=true\0"						\
-	"checkfdt=true\0"						\
-	""
-
-#define CONFIG_HW_ENV_SETTINGS						\
-	"hwconfig=fsl_ddr:ctlr_intlv=cacheline\0"			\
-	"usb_phy_type=" __stringify(__USB_PHY_TYPE) "\0"		\
-	"usb_dr_mode=host\0"
-
-#define CONFIG_KM_NEW_ENV						\
-	"newenv=sf probe 0;"						\
-		"sf erase " __stringify(CONFIG_ENV_OFFSET) " "		\
-		__stringify(CONFIG_ENV_TOTAL_SIZE)"\0"
-
-/* ppc_82xx is the equivalent to ppc_6xx, the generic ppc toolchain */
-#ifndef CONFIG_KM_DEF_ARCH
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	CONFIG_KM_DEF_ENV						\
-	CONFIG_KM_DEF_ARCH						\
-	CONFIG_KM_NEW_ENV						\
-	CONFIG_HW_ENV_SETTINGS						\
-	"EEprom_ivm=pca9547:70:9\0"					\
-	""
-
-/* App2 Local bus */
-#define CONFIG_SYS_LBAPP2_BASE		0xE0000000
-#define CONFIG_SYS_LBAPP2_BASE_PHYS	0xFE0000000ull
-
-#define CONFIG_SYS_LBAPP2_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBAPP2_BASE_PHYS) \
-				| BR_PS_8	/* Port Size 8 bits */ \
-				| BR_DECC_OFF	/* no error corr */ \
-				| BR_MS_GPCM	/* MSEL = GPCM */ \
-				| BR_V)		/* valid */
-
-#define CONFIG_SYS_LBAPP2_OR_PRELIM (OR_AM_256MB	/* length 256MB */ \
-				| OR_GPCM_ACS_DIV2 /* LCS 1/2 clk after */ \
-				| OR_GPCM_CSNT /* LCS 1/4 clk before */ \
-				| OR_GPCM_SCY_2 /* 2 clk wait cycles */ \
-				| OR_GPCM_TRLX /* relaxed tmgs */ \
-				| OR_GPCM_EAD) /* extra bus clk cycles */
-/* Local bus app2 Base Address */
-#define CONFIG_SYS_BR3_PRELIM  CONFIG_SYS_LBAPP2_BR_PRELIM
-/* Local bus app2 Options */
-#define CONFIG_SYS_OR3_PRELIM  CONFIG_SYS_LBAPP2_OR_PRELIM
-
-#endif	/* __CONFIG_H */
-- 
2.25.1



More information about the U-Boot mailing list