[PATCH V2 09/12] doc: board: Convert i.MX6 Sabreauto README to reST

[Peng Fan]

Convert plain text documentation to reStructuredText format and add
it to Sphinx TOC tree. No essential content change.

Signed-off-by: Peng Fan <peng.fan at nxp.com>
---
 board/freescale/mx6sabreauto/README  |  82 ----------------------
 doc/board/freescale/index.rst        |   1 +
 doc/board/freescale/mx6sabreauto.rst | 100 +++++++++++++++++++++++++++
 3 files changed, 101 insertions(+), 82 deletions(-)
 delete mode 100644 board/freescale/mx6sabreauto/README
 create mode 100644 doc/board/freescale/mx6sabreauto.rst

diff --git a/board/freescale/mx6sabreauto/README b/board/freescale/mx6sabreauto/README
deleted file mode 100644
index 710026a05e..0000000000
--- a/board/freescale/mx6sabreauto/README
+++ /dev/null
@@ -1,82 +0,0 @@
-How to use and build U-Boot on mx6sabreauto
--------------------------------------------
-
-mx6sabreauto_defconfig target supports mx6q/mx6dl/mx6qp sabreauto variants.
-
-In order to build it:
-
-$ make mx6sabreauto_defconfig
-
-$ make
-
-This will generate the SPL and u-boot-dtb.img binaries.
-
-- Flash the SPL binary into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
-
-- Flash the u-boot-dtb.img binary into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
-
-Booting via Falcon mode
------------------------
-
-Write in mx6sabreauto_defconfig the following define below:
-
-CONFIG_SPL_OS_BOOT=y
-
-In order to build it:
-
-$ make mx6sabreauto_defconfig
-
-$ make
-
-This will generate the SPL image called SPL and the u-boot-dtb.img.
-
-- Flash the SPL image into the SD card:
-
-$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 conv=notrunc && sync
-
-- Flash the u-boot-dtb.img image into the SD card:
-
-$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 conv=notrunc && sync
-
-Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
-
-$ sudo cp uImage /media/boot
-
-$ sudo cp imx6dl-sabreauto.dtb /media/boot
-
-Create a partition for root file system and extract it there:
-
-$ sudo tar xvf rootfs.tar.gz -C /media/root
-
-The SD card must have enough space for raw "args" and "kernel".
-To configure Falcon mode for the first time, on U-Boot do the following commands:
-
-- Load dtb file from boot partition:
-
-# load mmc 0:1 ${fdt_addr} imx6dl-sabreauto.dtb
-
-- Load kernel image from boot partition:
-
-# load mmc 0:1 ${loadaddr} uImage
-
-- Write kernel at 2MB offset:
-
-# mmc write ${loadaddr} 0x1000 0x4000
-
-- Setup kernel bootargs:
-
-# setenv bootargs "console=ttymxc3,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait quiet rw"
-
-- Prepare args:
-
-# spl export fdt ${loadaddr} - ${fdt_addr}
-
-- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
-
-# mmc write 18000000 0x800 0x800
-
-- Restart the board and then SPL binary will launch the kernel directly.
diff --git a/doc/board/freescale/index.rst b/doc/board/freescale/index.rst
index c9d7411875..cc079cadce 100644
--- a/doc/board/freescale/index.rst
+++ b/doc/board/freescale/index.rst
@@ -14,3 +14,4 @@ Freescale
    imx8qxp_mek
    imxrt1020-evk
    imxrt1050-evk
+   mx6sabreauto
diff --git a/doc/board/freescale/mx6sabreauto.rst b/doc/board/freescale/mx6sabreauto.rst
new file mode 100644
index 0000000000..fe4cd9d214
--- /dev/null
+++ b/doc/board/freescale/mx6sabreauto.rst
@@ -0,0 +1,100 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+mx6sabreauto
+============
+
+How to use and build U-Boot on mx6sabreauto
+-------------------------------------------
+
+mx6sabreauto_defconfig target supports mx6q/mx6dl/mx6qp sabreauto variants.
+
+In order to build it:
+
+.. code-block:: bash
+
+   $ make mx6sabreauto_defconfig
+   $ make
+
+This will generate the SPL and u-boot-dtb.img binaries.
+
+- Flash the SPL binary into the SD card:
+
+.. code-block:: bash
+
+   $ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
+
+- Flash the u-boot-dtb.img binary into the SD card:
+
+.. code-block:: bash
+
+   $ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
+
+Booting via Falcon mode
+-----------------------
+
+Write in mx6sabreauto_defconfig the following define below:
+
+CONFIG_SPL_OS_BOOT=y
+
+In order to build it:
+
+.. code-block:: bash
+
+   $ make mx6sabreauto_defconfig
+   $ make
+
+This will generate the SPL image called SPL and the u-boot-dtb.img.
+
+- Flash the SPL image into the SD card:
+
+.. code-block:: bash
+
+   $ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 conv=notrunc && sync
+
+- Flash the u-boot-dtb.img image into the SD card:
+
+.. code-block:: bash
+
+   $ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 conv=notrunc && sync
+
+Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
+
+.. code-block:: bash
+
+   $ sudo cp uImage /media/boot
+   $ sudo cp imx6dl-sabreauto.dtb /media/boot
+
+Create a partition for root file system and extract it there:
+
+.. code-block:: bash
+
+   $ sudo tar xvf rootfs.tar.gz -C /media/root
+
+The SD card must have enough space for raw "args" and "kernel".
+To configure Falcon mode for the first time, on U-Boot do the following commands:
+
+- Load dtb file from boot partition::
+
+   # load mmc 0:1 ${fdt_addr} imx6dl-sabreauto.dtb
+
+- Load kernel image from boot partition::
+
+   # load mmc 0:1 ${loadaddr} uImage
+
+- Write kernel at 2MB offset::
+
+   # mmc write ${loadaddr} 0x1000 0x4000
+
+- Setup kernel bootargs::
+
+   # setenv bootargs "console=ttymxc3,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait quiet rw"
+
+- Prepare args::
+
+   # spl export fdt ${loadaddr} - ${fdt_addr}
+
+- Write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)::
+
+   # mmc write 18000000 0x800 0x800
+
+- Restart the board and then SPL binary will launch the kernel directly.
-- 
2.28.0